Question about Cars & Trucks

Open Question

How to replace an O2 sensor on a 2008 KIA Sorento

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

fastboyz
  • 674 Answers

SOURCE: locating and replacing the o2 sensor on a 2005 kia spectra

a wrench and just unplug the sensor wire and screw out and install new one. they make a special socket but i just use a wrench.

Posted on Sep 11, 2008

  • 4 Answers

SOURCE: crankshaft sensor for 2004 kia sorento

The above information about the sensor being located at the top of the motor to the passenger side of center is bogus. That is only the pig tail plug in. The actual sensor pig tail continues down below, underneath the plastic lower timing belt cover, on the front of the motor, just above the crankshaft timing gear.

It is a very involved process of removing and replacing. You will have to remove all of the belts, the front timing belt covers, (upper and lower). You will also have to remove the front bracket that is mounted to the front of the block, which serves as the mount for the power steering pump, the alternator and the A/C compressor.You will also have to remove the crankshaft pulley. You cannot remove the plastic lower timing belt cover unless you remove all of these things first. The sensor is located underneath the lower cover. It has two bolts that hold it in place. You will have to remove these two bolts.

The crankshaft pulling bolt is a right handed thread and loosens by turning counter clockwise. The pulley will slip off but is a very tight fit. Do not try to turn it while removing it as there is a small pin that keeps it aligned to one position. Use a small ball pine hammer to tap it loose.

It is also a good idea to remove the electric cooling fan shroud that is mounted to the inside side of the radiator and the radiator hoses to give yourself more room to work. It has only two bolts at the top holding it in place. And then slips into two retaining clips at the bottom. Lifting it will pull it out of these retaining clips.

When you remove the small bypass hose located at the top of the radiator , to the passenger side, be careful not to break off the small nipple protruding out of the radiator tank. It is plastic and will break easily if you try to pull the rubber bypass hose from it. This will have to be taken to a radiator shop to have repaired if you accidentally break this off. Be sure to carefully loosen the hose from this nipple before trying to pull it off.

And one more thing, if you go to that much trouble to replace this sensor, it is a good idea to go ahead and replace the timing belt as well. It is a maintenance item and you will have to go through the same process to replace it as well. Do it once and do it all.

I hope this helps.

Posted on Nov 15, 2008

  • 1 Answer

SOURCE: Kia Sorento

http://www.kia-forums.com/kia-sorent...removal-2.html

Posted on Nov 18, 2008

  • 112 Answers

SOURCE: kia sorento electric aerial packed up.

Look under the wheel arch and remove the plastic cowl which protects the under side of the wing.
You will see the aerial under there.
good luck

Posted on Jan 31, 2009

emissionwiz
  • 75066 Answers

SOURCE: need to replace knock sensor/ O2 sensor 04 kia rio

IT IS IN THE SIDE OF THE ENGINE BLOCK, SCREWED INTO THE WATER JACKET OF THE BLOCK

Posted on Sep 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 kia sorento i neef to know o2 sensor location


The O2 sensor is in the exhaust system just of the engine and before the catalytic converter. Since some refer to the after cat converter sensor as an O2 sensor as well I would need to know the fault code you have. Also if this is a V6 it has two O2 sensors, one for each bank of cylinders

Feb 26, 2017 | Kia Cars & Trucks

1 Answer

How to fix 2012 kia sorento camshaft sensor


replaced crank and cam sensor [Archive] - Sorento Nation - KIA ...

www.sorentonation.com/forum/archive/index.php/t-913.html

20 posts - ‎6 authors
replaced crank and cam sensors put back together cranked up very rough idle some tapping any ... 12-17-2012, 12:24 AM ... It's a 2006 3.5 Kia Sorrento. ... I found theproblem the SUV has a aftermarket alarm and remote start system I tripped ...

Kia Rio Crankshaft Position Sensor Replacement - YouTube

? 4:44
https://www.youtube.com/watch?v=hihQxMWuSFY
Mar 21, 2014 - Uploaded by Jason Roush
While looking for how to replace a Kia Rio crankshaft positionsensor, ... is on and i have a P0340 code, think this is theproblem? kia rio 2002.

Kia Sorrento/Sedona: 3.5 Litre Engine/Timing Belt/Crank ...

? 20:23
https://www.youtube.com/watch?v=CjaD_zYPrUA
Mar 29, 2014 - Uploaded by JamieJones TheCarMan
Repair and/or Replacement tips for timing belt, crank sensor,cam sensor, water pump and drivebelt ...

Crankshaft position sensor - 2003 Kia Sorento - RepairPal

repairpal.com > Questions > Kia > Sorento > 2003 Kia Sorento


Jan 20, 2016 | 2012 Kia Sorento Base 4dr SUV 2.4L 4-cyl....

1 Answer

2008 Kia Sorento check engine light, codes P0700, P0641


Hi zero2blue,P0641 means Sensor Reference Voltage "A" Circuit/Open ,P0700 means Transmission Control System (MIL Request).Maybe you can use Autel MaxiDAS DS708 Update by Internet to sovle this problem,good luck!

Mar 06, 2014 | 2008 Kia Sorento 3.3

1 Answer

2003 kia sorento check engine light no symptoms


Scannign the PCM in order to know exactly what is the fault code that cause turn on "check engine light"; just with this fault code could send other details; ask your dealer about this.

Hope helps.

Feb 20, 2013 | 2003 Kia Sorento

1 Answer

2006 kia sorento o2 sensor


Has it had the gearbox out? just thinking if it is v6 (two o2 sensors) the plugs may have been put back on the wrong sensors. you wouldn't think that would make a diffrence but I remember reading something about that on some type of vehicle & it was causeing it to fault somehow. Can't realy remember but worth swapping the wires over for a test.

Jun 22, 2012 | 2003 Kia Sorento

1 Answer

2003 kia sorento keeps slowing down to a stop but doesnt cut off.I have to wait before I press on gas again.


I can't see the T/Belt giveing that problem however if the T/Belt is due it should be done ASAP because if the belt breaks it can cause pistons to hit valves (Very expensive to fix) but could be the catalytic converter or a number of other things. My thought would be to undo the o2 sensor in the exhaust & run car this will allow exhaust to escape without going through the catalyst. If car stops slowing to a stop you know that the catalyst is blocked. Or remove the catalitic converter & look through it it should look like honey comb you can see through. P.S your car posibly won't go without the o2 sensor in.

Jun 17, 2012 | 2003 Kia Sorento

2 Answers

What makes my 2004 kia sorento consumes fuel?


low tire presure
bad o2 sensor
need oil change
the way you drive
it could be alot of stuff
needs tune up

Dec 29, 2010 | 2004 Kia Sorento

1 Answer

Can't get the O2 sensor out of Kia Sorento, 2007 LX. Can't get it to turn. Any suggestions?


use a small hammer to "tap"the edge of the nut after spaying it with wd40.then if youve one, use a socket or ring wrench,(no slip)

Sep 06, 2010 | 2007 Kia Sorento LX 4x4

2 Answers

Check engine light came on for my 07 Kia Sorento & advance says it's an o2 sensor & misfire


have a 2004 sorento saids 02 senser out bank 1 top half what side is bank 1 passangerside or driver side

Nov 03, 2009 | 2007 Kia Sorento LX 4x4

1 Answer

04 kia sorento runs poorly


Might be going super simple here but from what you have said have you checked the wiring on your sensors? If you know that one works and you swap it and its not working its very possible the wires farther up are shorted or burned somewhere.

Nov 28, 2008 | 2004 Kia Sorento

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

114 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...