Question about 2002 Ford Mustang

1 Answer

Wont start changed the ignition switch and it will turn over but wont start

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 5,522 Answers

There is a part called an Inertia switch. It has a Reset button on it and will be fine once it is reset. Look at a photo on the Web at autoparts stores.

Most of the time the switch is located by the front floor kick panels. On a few models it is in the trunk on a side and behind the trunk carpet.

When you reset it, power will be restored to the fuelpump.

Posted on Feb 14, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why wont my 91 camaro start i drove it home one day shut it off and it hasn't started since i have changed the emc box the ignition switch the key and tumbler but it still wont start i can get it to turn...


Possible neutral safety switch failed if its an automatic, or inhibitor switch if standard trans. Does it have an alarm ? Did you get the ign switch in properly, if its the style that mounts down low on the column,loosen the screws and slide it back toward steering wheel and recheck for start

Mar 21, 2015 | 1991 Chevrolet Camaro

1 Answer

Car wont start when turn off changed battery/nuetral switch


try another key. the key could be worn where read coil in the ignition switch lock cylinder and immobilizer control module and ecm dont recognize ignition key or ignition switch key lock cylinder failing.

Nov 13, 2011 | 2002 Kia Spectra

1 Answer

1997 pontiac grand prix- car wouldn't start so we changed the alternator and charged the battery. it still wont start and now the key wont come out of the ignition.


Hello! The problem is the ignition lock cylinder itself...I would suggest changing the cylinder and the ignition switch...Purchase and change the Lock Cylinder first...If that solves the problem, stop there (The switch is costly...It may not be needed)...See photos below...Guru....Saailer


saailer_61.gifTurn the key to start ..1/16" Allen into the hole on top of the lock assembly to release the retaining pin...Turn to run...remove

saailer_62.gif

saailer_63.gif

saailer_109.jpgACDELCO Part # D1405D moreinfo2.png {#12369498} PART REQUIRES CODING AT GM DEALERSHIP....Cost $10

saailer_110.jpgColumn Shift...STANDARD MOTOR PRODUCTS Part # US422 ...Cost $100

saailer_111.jpg
STANDARD MOTOR PRODUCTS Part # US264With console shift...Cost $90

Jan 28, 2011 | Pontiac Grand Prix Cars & Trucks

1 Answer

96 ford explorer wont start. all power when turn key. nothing.


if it turns over from below,then its in the ignition switch and this also feeds power to the e.c.m. to make the engine fire so you either have a bad switch contact or the hot 12 volt wire to the ignition switch

Mar 20, 2010 | 1996 Ford Explorer

1 Answer

Flashing alarm light after battery change. Car wont start,


System operation
System arms 5 seconds after switching ignition OFF. Switch ignition ON. Ensure clock LED illuminates for 3-5 seconds. If LED flashes rapidly at regular intervals for approximately 1 minute, then flashes at irregular intervals: Key code not recognised. Remove key and try again.
Programming
When
System malfunction: LED illuminates for 1 minute, then flashes at irregular intervals. Key(s) added or replaced.
NOTE: Replacement keys MUST have blue mark. Keys with red mark are NOT compatible with this system.
How
NOTE: Programming method using vehicle keys can be deactivated using diagnostic equipment.
Obtain 2 programmed keys (A and B). Insert key A into ignition switch. Turn ignition switch to position II. Wait 1 second. Switch ignition OFF. Remove key A. Insert key B into ignition switch within 5 seconds. Turn ignition switch to position II. Wait 1 second. Switch ignition OFF. Remove key B. Within 10 seconds: Insert key to be programmed into ignition switch. Turn ignition switch to position II. Wait 4 seconds. Switch ignition OFF. Wait 5 seconds. Start engine. If engine does not start and clock LED flashes: Switch ignition ON. Wait at least 20 seconds. Switch ignition OFF. Repeat programming procedure. Repeat above procedure to program remaining keys. Keys can also be programmed using diagnostic equipment

Mar 08, 2010 | 2000 Ford Focus

3 Answers

Reset immobiliser


u must put a key to ignition and open a drive door 3 times and press and hold lock button

Jan 18, 2010 | 2007 Ford F

2 Answers

Starter wont stop cranking


bad ignition switch, not the ignition cylinder, ignition switch or starter soloined.

Oct 22, 2008 | 1987 Chevrolet S-10 Pickup

1 Answer

Wont start


make sure transmission is in park.

slide a stick or twig up underneath the steering column which will hold a specialized switch in place. Try the ignition. Should it start, the actual problem in the transmission interlock switch for the transmission [located in the center console] which also protects the ignition from turning on [secondary switch prior to the ignition switch]. What a ***** to have found... took me 8 hours but GM wanted 800$ for the fix.

Oct 11, 2008 | 2003 Pontiac Grand Am

Not finding what you are looking for?
2002 Ford Mustang Logo

66 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...