Question about 1984 Ford Bronco II

Open Question

Con you remove the computer on a 1984 bronco ii

Posted by Anonymous on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

frednewsome
  • 149 Answers

SOURCE: 1984 bronco II dies when going up hill

If the vehicle dies going up hill it may need a tune-up or check transmission fluid level to make sure the appropriate levels are set. Sometimes when level is low it creates a hard pull on the transmission when going up hills.

Posted on Nov 28, 2010

  • 14036 Answers

SOURCE: 1984 ford bronco II backfires

BACK FIRING THROUGH THE INTAKE COULD BE IGNITION TIMING OFF.AIR LEAK IN THE INTAKE OR STICKING INTAKE VALVES CAUSE BACKFIRING THROUGH THE INTAKE.

Posted on May 12, 2011

radar001
  • 1051 Answers

SOURCE: How do I check the trans fluid in my 1984 ford

I use and I'd recommend you register for free at www.autozone.com Once registered you'll have access to repair and shop manuals for virtually any car or truck. All the data and diagrams you need now or may need in the future will be a couple of mouse clicks away.

Posted on Jul 19, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1984 Bronco ii


starter silanoid feeds power to the coil after start up giving 9 volts could be giving to much voltage check with volt meter while running

Aug 27, 2012 | 1984 Ford Bronco II

1 Answer

Transfer case oil level


The oil specification for the transfer case in a 1984 Ford Bronco II is "Automatic Transmission Fluid, DEXRON II"

DEXRON II is pretty hard to find these days, so DEXRON III or MERCON III can also be used.

Jun 09, 2012 | 1984 Ford Bronco II

1 Answer

Flywheel torque specs for a 1984 ford bronco 2 xlt


if you have an impact wrench set it on 3 and run the bolts down until the impact just starts hammering torque is set

Dec 31, 2011 | 1984 Ford Bronco II

1 Answer

How do I check the trans fluid in my 1984 ford bronco II 4x4 with automatic transmission


I use and I'd recommend you register for free at www.autozone.com Once registered you'll have access to repair and shop manuals for virtually any car or truck. All the data and diagrams you need now or may need in the future will be a couple of mouse clicks away.

Jul 19, 2011 | 1984 Ford Bronco II

1 Answer

What carburator is stock for 1984 ford bronco 2 2.8 liter


http://www.hotrodders.com/forum/carb-2-8-l-v6-1984-ford-bronco-ii-132065.html

according to the site, a <350cfm holley carb should fit right on the motor and give you no problems, this will provide some reliability and tunability as well as aftermarket support for your application compared to factory, they should be very easy carbs to find used on ebay and such

Mar 01, 2011 | 1984 Ford Bronco II

1 Answer

1984 bronco II dies when going up hill


If the vehicle dies going up hill it may need a tune-up or check transmission fluid level to make sure the appropriate levels are set. Sometimes when level is low it creates a hard pull on the transmission when going up hills.

Nov 28, 2010 | 1984 Ford Bronco II

1 Answer

Where is the fuse box for 1984 ford bronco


Should be under the dash, driver's side.

Mar 05, 2010 | 1984 Ford Bronco II

1 Answer

What is the firing order 1984 ford bronco 2 2.8 liter


Cylinder numbers (front-rear)
Left (driver's) side 4-5-6
Right side 1-2-3
Firing order 1-4-2-5-3-6

Jan 25, 2010 | 1984 Ford Bronco II

4 Answers

What is the firing order for a 1984 ford bronco 2


1-4-2-5-3-6
Now you need to know which cylinder is which. If you stand at the front of the truck looking at the engine, the number 1 cylinder is on the left closest to you. The left bank has cylinders 1-3-5 and the right bank has 2-4-6. So number 1 is at the left front and number 6 is at the right rear.

Jan 25, 2010 | 1984 Ford Bronco II

1 Answer

WILL NOT IDLE . 1984 BRONCO 11 2.8 L V6


more than likely you have a bad computer. You need to have the I believe its called a ecIV computer in it checked.

May 08, 2009 | 1984 Ford Bronco II

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5481 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...