Question about 2004 Chevrolet Impala

Open Question

Brake diagram Ford Explorer 1996 - 2004 Chevrolet Impala

Posted by Anonymous on

2 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 76 Answers

SOURCE: i have a 1996 ford

maybe a wire shorted out or a fuse is blown

Posted on May 22, 2011

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I need a fuse diagram for ford explorer 1996

Go to the following and go to page 300. It is your owners manual and the fuse panels (underhood and instrument panel) are shown with fuse ID's.

Apr 11, 2013 | 1996 Ford Explorer

1 Answer

Need the diagram for a 1996 Ford Explorer , need too change the freeze plug in the back of the engine its leaking water

you can access a manual at you library or you parts store some freeze plugs are hard to get at you should have a hoist the removal and replacement procedure is important you may want to hire this done

Sep 17, 2012 | 1996 Ford Explorer

1 Answer

How do i change the brake switch on my 1996 ford explorer

Remove the panel under the dash above the brake pedal, lock up and you will see the switch on the brake pedal arm, you must remove the retainer cip as shown in the diagram below, it is #2. The switch is #6 in the diagram, it is a 15 minute job. I will caution you that the problem here is often not the brake light switch but the 2 wire connector to it, the copper wire conductor inside the outer plastic insulator breaks, so use a 12 volt test light ($4 at Autozone) to verify that you have power into the switch, if you do check the dead wire out of the switch to make sure the conductor is intact before you replace the switch. You can easily do this by removing the connector from the switch and putting a paper clip in it to see if the brake lights come on, if they do the brake light switch is the problem, if not then go to Ford and buy a repair connector for the brake light switch. Solder the new connector on (if needed) don't use crimp connectors.

Oct 27, 2011 | 1996 Ford Explorer

2 Answers

1996 Ford Explorer, stuck in park. Replaced ignition switch, selinoid, bushings... what?

The shift interlock solenoid works off of the brake lamp circuit. Check your brake lights to see if they are working. If the brake lights are not working, the most likely cause would be the brake lamp switch.

Mar 05, 2011 | 1996 Ford Explorer

2 Answers

Where is master brake cynlinder on 1996 ford explorer

under the bonnet on the end of the servo unit

Aug 12, 2010 | 1996 Ford Explorer

2 Answers

Looking for a diagram for ford explorer brakes

I'm not sure what you are looking for. Are you looking for brake line diagram? Diagram of brake assemblies? Vacumm diagram? Here's a couple, if they don't help, let me know exactly what you need.


Jan 11, 2009 | 1994 Ford Explorer Limited

Not finding what you are looking for?
2004 Chevrolet Impala Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides