Question about Cars & Trucks

Open Question

The light up button on my remote will not turn on for my entertainment center number 15190411

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i turn on rear entertainment system on 2006 toyota sienna


What do you mean "unlock"? There shouldn't be anything you need to unlock to use the rear entertainment center. If you put a DVD in the display it should come on and if you press the DISK button on the front stereo, you should get the sound of the DVD over the main speakers. Please elaborate more.

Jan 27, 2015 | 2006 Toyota Sienna

1 Answer

Horn do not blow when i lock my 2007 nissan truck with remote


Murano, maybe others.

This is adjustable through the center console, Key turned to the on position but not running, press settings, then you will see your selections, use the center knob to move up / down and enter to select. I believe it's the center choice & once you push the enter button, the display will show several options concerning locking the doors, lights, horn options for the remote. If that setting is correct and the horn isn't working, check your fuse/horn.

good luck

Mar 09, 2010 | 2005 Nissan Murano

1 Answer

Purchased a new clicker.from g/m.i can't program it.i have replaced the transformer under the dash panel that was used.. i have been told 96 models has several transmitters on it.


1. Move all Keyless Remotes out of range of vehicle. (10 to 15 feet)
2. Turn ignition key to the ON position.
3. Push the TRIP/ODO button on the DIC (Driver Info Center) twice.
4. Within 5 seconds, push & hold the FUEL INFO button on the DIC until
the PKE light comes on and stays on.
5. Turn the ignition to the OFF position, but leave the key in the ignition.
The PKE light will begin flashing.
6. Bring one Keyless Remote into range. The PKE light will stop flashing
and stay on to show the code is stored. Move the Keyless Remote out
of range. The PKE light will begin flashing indicating the system is ready
for the next Keyless Remote.
7. If more than one Keyless Remote is being programmed, move the first
Keyless Remote out of range and repeat step 6 for any additional Keyless
Remotes. Up to three Keyless Remotes can be programmed.
8. To turn off the programming mode, simply remove the key from the ignition
or turn the ignition switch on.
9. The programming mode will shut off after two minutes if.
A) You have not programmed any Keyless Remotes.
B) Removed the key from the ignition.
C) After three Keyless Remotes have been programmed.

Good luck and keep me posted.

Jan 23, 2010 | 1996 Chevrolet Corvette

1 Answer

Replaced battery on my remote control and it does not work. does it needs to be re-programmed again?


Use this Procedure for Vehicles with
Driver Information Center Buttons

This information is in your Owners Manual in the
Drivers Information Center Section.


1. Insert Key and turn to ON position so you can access Driver Information Center

2. Press the vehicle information button until
PRESS TO RELEARN REMOTE KEY displays

3. Press the set/reset button until
REMOTE KEY LEARNING ACTIVE displays

4. Press and hold the lock and unlock buttons on the first keyless remote at the same
time for approximatley 15 seconds. A chime will sound indicating that the remote is
programmed.


5. To program additional remotes at this time repeat step 3.
This vehicle can have a maximum of eight remotes programmed.

6. To exit programming mode turn key off and remove key.
Test remote(s).

Use this Procedure for Vehicles without
Drivers Information Center Buttons

To access this display, the vehicle must be in Park (P) with key in the on position (as far
as you can go without cranking engine)

1. Press the trip odometer reset stem until RELEARN REMOTE KEY displays.
2. Press and hold the trip odometer reset stem for three seconds.
The message REMOTE KEY LEARNING ACTIVE will display

3. Press and hold the lock and unlock buttons on the first keyless remote at the same
time for approximately 15 seconds. A chime
will sound indicating that the remote is
programmed.

4. To program additional remotes at this time repeat step 3.
This vehicle can have a maximum of eight remotes programmed.
5. To exit programming mode turn key off and remove key.
Test remote(s).


Good luck and hope this helps, you may have to reprogram. merry Xmas


Dec 24, 2009 | 2007 Chevrolet Tahoe

2 Answers

How do i program a key fob for a 1996 cadillac deville


you need to get a tech 2 to be able to promram the key fob

Aug 02, 2009 | 1996 Cadillac DeVille

1 Answer

I have a volvo xc90, driver side res screen comes up white


I had this problem as well in my 2005 XC90. It turned out that it was switched on audio. Use the remote to switch back to DVD.

Jun 04, 2009 | 2005 Volvo XC90

2 Answers

Keys won,t lock or unlock doors


Use this Procedure for Buick Vehicles "With" Driver Information Center Buttons.

This information is in your "Owners Manual" in the "Drivers Information Center Section."

1. Insert Key and turn to ON position so you can access Driver Information Center.

2. Press the vehicle information button until PRESS TO RELEARN REMOTE KEY displays.

3. Press the set/reset button until REMOTE KEY LEARNING ACTIVE displays.

4. Press and hold the lock and unlock buttons on the key-less remote at the same
time for approximately 15 seconds. A chime will sound indicating that the remote is
programmed.

5. To program additional remotes at this time repeat step 4. This vehicle can have a maximum of eight remotes programmed.

6. To exit programming mode turn key off and remove key. Test remote(s).


Use this Procedure for Buick Vehicles "Without" Drivers Information Center Buttons.

To access this display, the vehicle must be in Park (P) with key in the on position (as far as you can go without cranking engine).

1. Press the trip odometer reset stem until RELEARN REMOTE KEY displays.

2. Press and hold the trip odometer reset stem for three seconds. The message REMOTE KEY LEARNING ACTIVE will display

3. Press and hold the lock and unlock buttons on the first key-less remote at the same
time for approximately 15 seconds. A chime will sound indicating that the remote is
programmed.

4. To program additional remotes at this time repeat step 3. This vehicle can have a maximum of eight remotes programmed.

5. To exit programming mode turn key off and remove key. Test remote(s).

Good Luck !

Mar 25, 2009 | 2005 Buick LaCrosse

1 Answer

2005 cadillac sts remote transmitter


This is the procedure for a reprogram of the remote's from the factory service manual, if it doesn't work then u may have a receiver issue.
Use this Procedure for Vehicles with
Driver Information Center Buttons

This information is in your Owners Manual in the
Drivers Information Center Section.


1. Insert Key and turn to ON position so you can access Driver Information Center

2. Press the vehicle information button until
PRESS TO RELEARN REMOTE KEY displays

3. Press the set/reset button until
REMOTE KEY LEARNING ACTIVE displays

4. Press and hold the lock and unlock buttons on the first keyless remote at the same
time for approximatley 15 seconds. A chime will sound indicating that the remote is
programmed.


5. To program additional remotes at this time repeat step 3.
This vehicle can have a maximum of eight remotes programmed.

6. To exit programming mode turn key off and remove key.
Test remote(s).


Use this Procedure for Vehicles without
Drivers Information Center Buttons


To access this display, the vehicle must be in Park (P) with key in the on position (as far
as you can go without cranking engine)

1. Press the trip odometer reset stem until RELEARN REMOTE KEY displays.
2. Press and hold the trip odometer reset stem for three seconds.
The message REMOTE KEY LEARNING ACTIVE will display

3. Press and hold the lock and unlock buttons on the first keyless remote at the same
time for approximately 15 seconds. A chime
will sound indicating that the remote is
programmed.

4. To program additional remotes at this time repeat step 3.
This vehicle can have a maximum of eight remotes programmed.
5. To exit programming mode turn key off and remove key.
Test remote(s).

Jan 17, 2009 | 2005 Cadillac STS

1 Answer

Wireless Headphones in the Entertainment System


THERE IS A HEADPHONES BUTTON ON THE REMOTE. yOU HAVE TO TURN IT ON THAT WAY. I RETURNED 2 SET OF "FAULTY HEADSETS" BEFORE I FIGURED IT OUT...

Oct 05, 2008 | 2004 Chrysler Pacifica

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

10 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...