Question about Cars & Trucks

Open Question

How do u remove hard skin from the bottom of your feet with listerine

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i remove rear bumper 2010 liberty wagon


RTM?
pulls skins
unbolt it?
05 liberty, called KJ

fsm quote
skins are facia
1.BODY/EXTERIOR/REAR WHEEL OPENING
FLARE MOLDINGS - REMOVAL)
(2) Remove the rear lamp units. (Refer to 8 -
ELECTRICAL/LAMPS/LIGHTING - EXTERIOR/
REAR LAMP UNIT - REMOVAL)
(3) Remove the four side bolts. (Fig. 2)
(4) Remove the two bottom rivets.
(5) Remove the 3 screws along the upper edge.
(6) Separate the side plastic retainers and remove
the fascia from the vehicle.

once this is off, all else is obvious. steel parts. damaged
you never state why or if damage was present so....


Mar 10, 2015 | 2010 Jeep Liberty

1 Answer

Remove door lock hiace van


the factory Service manual covers this (buy one if DIY or get service)
you never said what door?
if front passenger/driver door, all cars are much the same.
1: remove door card (the inside skins) and handles first.
arm reset on some.
2: remove the card skins, some unscrew, some just pop off from bottom to top.
3: remove plastic sheet (thin) if still there (moisture barrier)
4: see lock , sure, remove link clips (they turn and unlock)
5: unbolt lock.

Dec 05, 2014 | Toyota HiAce Cars & Trucks

1 Answer

Remove drivers door


unbolt the outer door skin by removing the door handle fist there is a small pin in the bottom of the handle next to the lock when you have that out you will need to remove the t25 bolts that holds the skin to the fram

Sep 03, 2013 | 1992 Saturn SC

1 Answer

HOW TO CLEAN The carb throat


I usually gargle with listerine or salt water....Only kidding..Get a can of Berrymans B-12 Chemtool, The spray type... Flush the throat well with the B-12. I do it with the engine at a medium to high idel.

Jul 06, 2012 | 2001 Chevrolet Silverado 1500

1 Answer

Is there a place I can go that would give me instruction on how to change out the inside and outside passenger door handles on my 1999 Toyota corolla?


The best place to look would be a hanes repair manuel you can get them at about any parts store. The other place online Google search 99 toyota corolla door skin removal. alout of times you can unscrew all the screws in the panel if power acceceries are on the arm rest should be able to pull up the back side and pull up and out then there should be corigated clips that hold the door skin on pull loose the bottom and push up and the door skin should come up be carefull when pulling don't pull to hard where the panel breaks they actully sell flat prying tools to remove the corigated pins when ready to put back together put the pins in the door skin start at the top slid top in push lower in install bolts. Removing the outerpanel best off to change door when the door skin is off it is much lighter. there is bolt clusters in the door hinges you will have to remove plus any wires. when putting new door on get another person to hold the door while instaling it will make it much easier. Keep bolt snug and push new door until alined open and tighten bolts

Feb 28, 2011 | Toyota Corolla Cars & Trucks

1 Answer

Rear hatch wont close. what is door skin? says to remove to find lock gears?


hi door skin or door panel as it should be, is the panel that covers the inside of the door normally held in by a few screws and some poppers, lock gears, are the mechanical parts to the door latch, once you gain access to the inside of the door by removing the door panel, you will see the latch/latches either side or at the bottom...hope this helps

Oct 10, 2010 | 1997 Jeep Grand Cherokee

2 Answers

The drivers side door won't open from the outside. How do you take the door apart from the inside? Thanks!


There are a couple of screws holding the armrest in place, remove them. Using a small pick type of tool, pop out the power window master switch, there is another screw under it. The door panel itself is held in place with push clips, so grab the panel from the bottom and pull it out until all the clips are out of the door, then slide it straight up to get it off the top of the door edge.

Nov 22, 2009 | 1993 Buick LeSabre

1 Answer

Cannot remove outside door handle


If you look under the handle you will see two round flat rivet heads. You will need to remove the door skin. Roll the window all the way down. Pull the plastic trim up off the window regulator arm/handle and unscrew it, there is a screw inside the arm rest in the place where your fingers go, and another screw behind the inside door handle that holds the plastic molding in place. After those are unscrewed it is just a matter of popping off the skin with a suitable pry bar or trim plug pry bar tool (the door skin is attached by plastic barbed plugs that go around the outside of the door) Pry from the bottom 1st, then the sides. Lift skin away from door from bottom and then pull up to remove skin from door...this will release it from the top where the skin attaches inside the door next to the glass.
Temporarily attach the window handle and roll up the window. Cut the doors inside plastic liner to gain access to the inside (Duct Tape this all back up air tight when re-assembly). Keep that window handle close...you may have to adjust the window height to move the glass/arm out of your way.
Once the outside handle is drilled out (use a big drill bit and go just deep enough to break the head off then use a punch to drive out the rivet) you just have to unhook the metal arm that goes to the latch. Bolt on a new handle and re-assembly is reverse of disassembly. Take advantage of having the inside of the door open to lube up the window regulator or even spray a good dose of Rust Check etc inside to protect it from rust. Rangers are pretty bad for having the bottoms of the doors rust out.

Nov 22, 2009 | 1996 Ford Ranger SuperCab

3 Answers

Replace door skin on 1996 camaro


I see this was asked years ago but never answered. So for the future questions about this,
The doors and roof panels on 4th Gen F-bodies are SMC (Sheet Molded Compound), a form of fiberglass. The skin is glued on. To remove a glued on panel use either a heat gun or a plumbers torch (Map Gas). Heating around the skin where the panel is bonded to the inner structure will break down the adhesive. Be careful not to burn the SMC away in a fire (heat guns are safer than the torch). Where you start, insert a putty knife to lightly pry the skin off as you heat the area.

Mar 27, 2009 | 1996 Chevrolet Camaro

1 Answer

Replace driver's side door hdle & locking mechanism on 02 Protege


Removing the door skins are not hard, the problem is that they normally use a special tool. Without the tool you may break a few of the plastic clips. If so no worries go to your local automotive department and look for the clips. 
You will also have at least one screw that attaches the skin to the door frame. Usually remove the bottom of door panel and work around both sides until you get to the window. Then remove the screw and unplug any of the power options..
Haynes or  Chiltion manual for your car should show you details.. It is easy for the average DIY person.
The handle is just as easy. Do you have metric and torx because you will need them.

Dec 03, 2008 | 2002 Mazda Protege

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...