Question about Isuzu Rodeo

Open Question

Replaced intake manifold gasket and now vehical wont start i checked all fuse and relays thier ok checked crank sensor its ok no injector pulse replaced icm and the problem stii there have voltage to but none out on new icm its a 19996 rodeo 3.2l engine

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 43 Answers

SOURCE: service engine soon light on 2002 chevrolet tahoe stays on

That normally means that you have a issue with your gas cap try replacing your gas cap first then diconnect the negative terminal of the battery for about three minutes to clear the memory and start the truck again

Posted on Apr 11, 2009

Ad
  • 740 Answers

SOURCE: 1993 honda accord 2.2,no injector pulse

This sounds like a main relay problem here is a diagram its located under the dash under steering column its the brownish -orange box in the picture. http://www.tegger.com/hondafaq/mainrelaylocation/7-main_relay_closeup.jpg Good luck and thanks for using FIX YA

Posted on May 15, 2009

  • 22 Answers

SOURCE: 1998 Lincoln engine cranks but does not start.

check the fuel shut off switch in the trunk

Posted on Nov 03, 2009

ftw1952
  • 10319 Answers

SOURCE: 2001 honda civic ex,wont start, no injector pulse,

Injector pulses are sent from the engines computer. Have that checked out

Posted on Apr 07, 2010

  • 972 Answers

SOURCE: 2002 Kia Sportage will not start.

p0560 is system voltage problem. open or short between the battery positive and the ecm.CHECK ALL FUSES. dosnt matter what they are labeled under dash and under hood replace any that are bad and retry to start. no start then check voltage to ecm grounds to. i dont have a wireing diagram to give you but for a small fee or free the dealer can make you a copy.make sure all the wires that go to battery terminals are not corroded and are making good contact [verified with volt meter]. if after all checks ok then replace ecm. as a side note i havent had to change one ever.

Posted on Apr 11, 2010

Testimonial: "Thank you for the help. We will continue to check all fuses and wires."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

87 chevy s10 blazer 2.8 has power to all related components but no spray from injectors cranks but wont start


-Use noise light to check each injector wire connector to see
If there is power there or not when you crank.
-If there is not power at all then 90% the cam & crank sensor are effect.
Good luck

Mai

Jan 25, 2017 | Cars & Trucks

1 Answer

1996 Toyota Corolla cranks will not start. Has spark, fuel pressure at rail, no injector pulse with noid light when cranking. MIL light very dim. Unable to retrieve fault codes


Check distributor rotation to ensure good timing belt. If good, check crank and cam position sensors. The computer fires the plugs and injectors based on many factors but most importantly the crankshaft and camshaft position.

Jan 24, 2017 | Toyota Corolla Cars & Trucks

3 Answers

Ok replaced the intake manifold , car wont start, checked crank sensor, checked plugs and wires. fuses, fuel injectors ,engnition sensor bad , replaced it coil packs good and still wont start .getting...


or you getting the right fuel pressure? check fluid filter, check pressure regulator, check spark plugs to see if they are soaking wet if they or wet take them all out and pull fuel pump relay out turn engine over and blow all gas out the plug holes. install plugs and relay and try start again , check engine compression, check coolant senor ,check cam sensor

Jul 06, 2011 | 1999 Pontiac Grand Prix

1 Answer

My Altima SE R will not run. I replaced the fuel pump, but we are learning that there is no pulsation to the fuel injectors. We checked out the immobilizer and its fine, all the cam sensors are fine, the...


First guess is anti theft.
Leave key on for half an hour and/or lock unlock doors with remote.
Does the tack on the dash show rpm when cranking the engine?If it does you should have a injector pulse using a noid light.
If you have rpm showing and no injector pulse try borrowing a computer from a vehicle like yours.
No RPM showing when cranking?
Check/change crank and cam sensors and possibly computer.
Cam timing can cause no start but you should have an injector pulse even with a jumped tooth or two on the timing chain.

Apr 02, 2017 | 2005 Nissan Altima

1 Answer

Crank no start with spark and fuel after replacing intake manifold gasket


Make sure the injectors are getting pulse,if they are not,check the harness to the injectors.

Apr 25, 2010 | 1991 Chevrolet Lumina

2 Answers

02 caviler.. cranks but will not start.. have replaced crank sensor,fuel relay sensor.ignition module as well as spark plug module... and replaced battery


Squirt starting fluid in intake and try to start if it starts and then dies you have a fuel delivery problem. Make sure you check the fuses for a blown fuse namely fuel pump or fuelpump relay. If it doesnt start after squirting starting fluid in the intake check for spark at the plug wires and coil.

Dec 02, 2009 | 2002 Chevrolet Cavalier Coupe

1 Answer

I have a 2001 camaro with a 3800 v6 it cranks but wont start. no feul and the injectors are not firing. i can jump the feul pump relay and get feul pressure but the injectors will not fire.


The crank sensor is what pulses the ijectors,and makes the spark,so I would start at the crank sensor.Let me know how you come out.Check for any blown fuses also.Ecm fuse would cause this,but it may be called anything ,so check all fuses.

Sep 10, 2009 | 2001 Chevrolet Camaro

2 Answers

Grand cherokee 2000 starting probs


you need to see if you have spark and check all fuses and see if you have fuel pressure and injector pulse if no spark and no injector pulse suspect crank sensor or ignition control module if no fuel pressure check fuses then relays and then suspect pump

Aug 18, 2009 | 2000 Jeep Grand Cherokee

2 Answers

Will not start after it stalls untill about 5-10 minutes


spray carb cleaner on the intake manifold near cylinder 1... common problem is the intake manifold gasket leaks vacuum causing a misfire...the not starting could be due to a faulty crank sensor

Feb 27, 2009 | 2002 Saturn Sl

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14380 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...