Question about 1990 Ford Econoline

1 Answer

Location of relay for fuelpump - 1990 Ford Econoline

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

  • Contributor
  • 1 Answer

Drivers side front fender by battery

Posted on Feb 13, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1992 Audi 500se the fuelpump relay makes a clicking noise then the fuelpump stops and the car shuts down when I'm driving is the relay the problem or the fuelpump?


If pump is drawing excess current, relay can get too hot and fail. So answer is probably bad pump (clogged filter?) and now may need relay also.

Jan 23, 2015 | Audi Cars & Trucks

1 Answer

Where is the fuel pump relay on a 1991 gmc jimmy


Thye fuelpump relay is located to the right of the brake booster. this is for a 1991 gmc jimmy (s-15)

I have enclosed a diagram to help locate the relay.

The most common reason for no fuel pressure on these trucks is not the relay but rather the fuelpump itself. the pump is located inside the fuel tank.

There is also a problem with the wiring to the fuel pump, you will need to locate the top of the tank and then off to side of tank is wiring .
This wiring comes off the top of the tank, you will need to check and there is connector problems..
there is one or two ground wires that come off wiring to top of tank which run to frame, check to make sure the grounds are good. if you end up with a bad pump you will see a notice to rewire a new fuelpump connector. hope this is helpful. good day.3_4_2012_1_29_16_am.gif

Mar 03, 2012 | 1991 GMC S-15 Jimmy

1 Answer

Wiring diagram


Then the fuel pump has failed most likely. It is electric of course and located inside the fuel tank, the fuel tank must be removed in most cases to replace the fuel pump, and don't forget to replace the fuel filter

Feb 07, 2012 | Mitsubishi L200 Cars & Trucks

2 Answers

NEED TO KNOW WHERE THE FUEL PUMP RELAY SWITCH IS FOR A 1998 CHEVY S10 TRUCK...


For the 1998 s10 theres no fuelpump switch, there is a fuelpump relay. the relay is in the engine compartment inside the fuse/relay box. the relay will be labeled on the inside cover of the fuse/relay box cover. besides the relay the only other problem for a fuelpump not working on these trucks is the fuelpump is bad or the wiring connector to the pump is bad.

Aug 27, 2011 | Chevrolet Chevy Cars & Trucks

1 Answer

L.co.zawhere can I find the fuelpump relay of 1999 2lt Sonata


The fuelpump relay for a 1999 sonata is located behind the center console below the radio. good day.

Apr 13, 2011 | 1999 Hyundai Sonata

1 Answer

91 ford explorer 4.0 where is the fuel pump relay? some say under hood and others say passenger side fire wall inside of vehicle near floor board?


The fuelpump relay is located under the hood on the right side fender well, rightside would be the passenger side and is inside the relay box, heres a diagram to help you locate the relay, good luck.johnjohn2_52.gif

Jan 03, 2011 | 1991 Ford Explorer

2 Answers

I have replaced the fuel pump amongst a lot of other things. I can spray gas or starting fluid in the throtal body and it will run rough untill the fumes ware out. Its a 1995 ford explorer 4x4 xlt


If you hear the fuelpump operate the first 1 or 2 seconds when the key is turned to RUN position, the fuelpump is working. If you do not hear the fuelpump run, check the Inertia switch which should be in the side panel of the rear cargo area. If you have an owners manual check for the Inertia switch location.

To reset the Inertia switch, hold the button on it for 2-3 seconds. You should now hear the pump run. You may also have a fuelpump relay under the hood in one of the Powerboxes. The Powerbox may have a fusible link from the Battery. When the fusible link is OK and the Pump Relay is OK, there is a fuse in the Fuse panel. Then finally the Ignition switch will trip the Pump relay. As power flows through the wire to the fuelpump the Inertia switch can break the power connection.

So you have 5 powerpoints before the fuelpump will work. Fusible link, Pump Relay, Fuse Panel, Ignition Switch,and Inertia switch. These must all work before the fuelpump can run.

Aug 14, 2010 | 1995 Ford Explorer

1 Answer

Power to fuelpump


If you find the relay you may not need to run a wire. make sure the relay is working.

Apr 24, 2010 | 1984 Toyota Celica Supra

2 Answers

Where is the fuel cutoff relay located


Check the position 41 for Fuel Pump relay...

3c171fd.gif

Hope this help (remember comment and rated).

Apr 06, 2010 | 1999 Oldsmobile Bravada

1 Answer

New fuelpump & relay, fuelpump want come on.


check all those item again, especially the crank sensor, check the fuel pump by adding 12v to it, make sure its good. tun on key, make sure your getting 12v from fuel pump wire

Jul 30, 2009 | 1996 Chevrolet Cavalier

Not finding what you are looking for?
1990 Ford Econoline Logo

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...