Question about Mazda Cars & Trucks

Open Question

Mazda e2200 rear light exchange - Mazda Cars & Trucks

Posted by Anonymous on


2 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 7353 Answers

SOURCE: hi my gear box is stuck in 4th gear, is it front mazda e2200 van


Posted on Nov 10, 2009


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

My mazda 3 1.6 diesel on a 2006 will not start up the alarm light on my dash board keeps flashing at a fast pace. what could be the problem?

Mazda 3 diesel

Might seem far fetchted, but try to exchange the light bulb in the glove compartment, it will solve your problem

Feb 16, 2011 | Mazda MAZDA3 Cars & Trucks

1 Answer

How do you tighten the fanbelt on a mazda E2200 panel van

see the generator in the engine the fan belt goes around it there is a iron strip attached to the generator which holds the generator loosen this screw a bit and pull the generator with an iron bar or some thing that can when the belt is tight tighten the screw

Jan 29, 2011 | Mazda B2200 Cars & Trucks

1 Answer

I have a mazda e2200 1988 diesel van. the 10 amp engine fuse keeps blowing, what can cause this?

There could be a short to ground in one of the wires. Perhaps take it to an auto electric shop to investigate further.

Aug 14, 2010 | Mazda B2200 Cars & Trucks

3 Answers

Gear box is stuck in 4th gear on my mazda e2200

check the linkages (rods connecting stick and gearbox) my e2000 is also stuck in third mechanic friday then ill post my discoveries

Nov 10, 2009 | 1986 Mazda 626 Coupe

1 Answer

E2200 oil light comes on when cold then goes off after warmed up. The oil level is good

try replacing oil preasure switch, if light still comes on then have oil preasure checked , (when cold) may need oil pump if presure is low, if you caught problem early you wont do any engine damage, again start with the switch .hope this helps.

Oct 15, 2009 | 1988 Mazda B2200

1 Answer

Ho do I change Mazda E2200 headlight bulb please ?

they will push in and twist out be careful not to touch the new bulb with your fingers while handling it just the metal part to reinstall or it many have a coupler to remove in the same fashion

Sep 12, 2009 | Mazda B2200 Cars & Trucks

2 Answers

Mazda 1997 E2000 VAN, WIPERS WORKING only dead slow, replaced motor, switch & control

hi fixya pls i need a mazda e2200 van to buy and my name is fitzgerald from west africa ghana . and email address is

Dec 14, 2008 | 1999 Mazda B-Series

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts


Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8826 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides