Question about 1988 Daihatsu Charade

Open Question

How to adjust charade 1987 diesl pump timing cl 3 engine

I m looking for a picture that how to adjust diesel pump timing belt as there are no align mating marks are there>regards

Posted by on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: TIMING MARKS CAMBELT REPLACEMENT FOR CL-T CHARADE, PLEASE

Hi Cas,

1) timing belt - see the small dot on tooted crank (small) pulley and match this with a notch ^ on engine body. Align the 'F' on overhead camshaft front pulley with lower crank shaft (small pullet). You should also alight the top pulley with a ^ on right side of big pulley when facing engine from front

In case of diesel pump:
2) cam belt - alight the dot mark on small camshaft pulley with notch ^ on tappet cover. Move and hold pump pulley and alight it with dot on this pulley to dot mark on plate to which pump is bolted.

Regards,

Gulfraz, Karachi, Pakistan

Posted on Jan 25, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to put in time timing belt


I think that the alignment if the belt was done incorrectly. Every sprocket has an alignment mark on it as to the way the belt needs to be installed this needs to be checked again when the belt is tight. The modern pulleys that tighten the belt will in indicate what tension the belt needs to have. The alignment marks meet up with each other. If is important for proper alignment. It sound like you did not have the car on top dead center or TDC. Therefore it is shaking back and forth and dies in gear. In other words the pistons are not making enough compression to keep the engine running. Look up on the Internet the alignment for your engine and it will show you pictures as to what you need to do. Also next time if you mention what engine type you have e.g. 1.8 l turbo etc. will help as well. I may have had a picture of the alignment for the sprockets. Good luck. Before I forget replace the water pump as well. If the belt is bad the pump will go soon as well. The pump works of the timing belt and can cause alot of damage to the engine.

Apr 26, 2015 | 2003 Volkswagen Passat

1 Answer

Timing marks trooper 1985 mod dlx turbo diesel


Refer to Figures 1,2,3,4 when performing 17-step timing procedure for 1981-1985 Diesel Engines.

Fig 1. Injection pump and camshaft alignment marks - Diesel engine.

archaeology_66.jpg


Fig 2. Removing the timing belt holder - Diesel engine.

archaeology_67.jpg

Fig 3. Injection pump alignment marks - Diesel engine.

archaeology_68.jpg

Fig 4. Tensioiner Pulley Bolt Sequence - Diesel engine.

archaeology_69.jpg

Procedure - Timing Belt replacement.

1. Disconnect the negative battery cable. Drain the cooling system.

CAUTION
When draining the coolant, keep in mind that cats and dogs are attracted by ethylene glycol antifreeze, and are quite likely to drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantity. Always drain the coolant into a sealable container. Coolant should be reused unless it is contaminated or several years old.

2. Remove the timing belt cover. Remove the injection pump sprocket flange.

3. Using a prybar, remove the tension spring from the timing belt tensioner.

When removing the tension spring, avoid using excessive force for the spring may become distorted.

4. Remove the tensioner pulley bolt and the pulley.

5. Remove the timing belt and discard it.

To install:

6. Rotate the crankshaft to bring the No. 1 piston to TDC of the compression stroke.

7. Align the timing marks on the injection pump sprocket with the camshaft sprocket; the marks must be facing each other.

8. Using a new timing belt, install it in the following sequence: crankshaft sprocket, camshaft sprocket and the injection pump sprocket; the slack must be between the injection pump and camshaft sprockets.

9. Install the tension center and the tension pulley so the end of the tension center is fitted against both pins on the timing pulley housing.

10. Hand tighten the nut so the tension pulley can be rotated freely.

11. Install the tension spring and semi-tighten the pulley nut to 22-36 ft. lbs. (30-48 Nm).

12. Rotate the crankshaft 2 full turns clockwise to seat the belt and further turn the crankshaft 90° beyond TDC to settle the injection pump.

13. Loosen the tension pulley nut to take up the timing belt slack. Tighten the tension pulley nut to 79-94 ft. lbs. (108-128 Nm).

14. Install the injection pump sprocket flange; the hole in the outer circumference of the flange should be aligned with the triangular timing mark on the injection pump sprocket.

15. Rotate the crankshaft 2 full turns clockwise to bring the No. 1 piston to TDC of the compression stroke. Make sure the triangular timing mark on the timing sprocket is aligned with the hole in the flange, then, measure the timing belt tension; it should be 33-55 lbs.

16. Install the timing belt cover.

17. Connect the negative battery cable.

Jul 04, 2011 | 1995 Isuzu Trooper

1 Answer

I need the timing settings for a 1987 transit ice cream van with a diesel engine with the cav pump


its done by moving the diesel pump there is a bolt you loose it and adjust the timing

Feb 03, 2011 | Ford Transit Connect Cars & Trucks

1 Answer

Diagram for volkwagon transporter 1997 2 litre 4 cylinder timing belt replacement


I found a 2.0L VW engine for a Cabrio. Not sure if this is the right one, but here goes:

REMOVAL & INSTALLATION

NOTE: Do not turn the engine or camshaft with the timing belt
removed. The pistons will contact the valves and cause internal engine damage.

Gasoline Engines






Fig. 1: Adjusting the belt tension on a 2.0L 8 valve
91223g06.gif







Fig. 2: Remove the timing belt cover
91223p51.jpg







Fig. 3: Align the timing marks
91223p46.jpg







Fig. 4: Locate the tensioner
91223p47.jpg







Fig. 5: Loosen the tensioner bolt
91223p48.jpg







Fig. 6: Mark the belts direction of rotation
91223p52.jpg



  1. Disconnect the negative battery cable and remove the accessory drive belts,
    crankshaft pulley and the timing belt cover(s).
  2. Temporarily reinstall the crankshaft pulley bolt and turn the crankshaft to
    TDC of No. 1 piston. The mark on the camshaft sprocket should be aligned with
    the mark on the inner timing belt cover or the edge of the cylinder head.
  3. With the distributor cap removed, the rotor should be pointing toward the
    No. 1 mark on the rim of the distributor housing. On 8 valve engines, the notch
    on the crankshaft pulley should align with the dot on the intermediate shaft
    sprocket.
  4. Loosen the locknut on the tensioner pulley and turn the tensioner
    counterclockwise to relieve the tension on the timing belt.
  5. Slide the timing belt from the sprockets.
    To install:

  6. Check the alignment of the timing marks. On 16 valve engines, the mark on
    the tooth should align with the mark on the rear belt cover.
  7. Install the new timing belt and tension the belt so it can be twisted 90°at
    the middle of it's longest section, between the camshaft and intermediate
    sprockets.
  8. Recheck the alignment of the timing marks and, if correct, turn the engine 2
    full revolutions to return to TDC of No. 1 piston. Recheck belt tension and
    timing marks. Readjust as required. Torque the tensioner nut to 33 ft. lbs. (45
    Nm).
  9. Install the belt cover and accessory drive belts.
  10. If the belt is too tight, there will be a growling noise that rises and
    falls with engine speed.


Diesel Engines

Some special tools are required. A flat bar, VW tool no. 2065A, is used to
secure the camshaft in position. A pin, VW tool no. 2064, is used to fix the
pump position while the timing belt is removed. The camshaft and pump work
against spring pressure and will move out of position when the timing belt is
removed. It is not difficult to find substitutes but do not remove the timing
belt without these tools.
NOTE: Do not turn the engine or camshaft with the timing belt
removed. The pistons will contact the valves and cause internal engine damage.



  1. Disconnect the negative battery cable and remove the accessory drive belts,
    crankshaft pulley and the timing belt cover(s). Remove the camshaft cover and
    rubber plug at the back end of the camshaft.
  2. Temporarily reinstall the crankshaft pulley bolt and turn the crankshaft to
    TDC of No. 1 piston. The mark on the camshaft sprocket should be aligned with
    the mark on the inner timing belt cover or the edge of the cylinder head.
  3. With the engine at TDC, insert the bar into the slot at the back of the
    camshaft. The bar rests on the cylinder head to will hold the camshaft in
    position.
  4. Insert the pin into the injection pump drive sprocket to hold the pump in
    position.
  5. Loosen the locknut on the tensioner pulley and turn the tensioner
    counterclockwise to relieve the tension on the timing belt. Slide the timing
    belt from the sprockets.
    To install:

  6. Install the new timing belt and adjust the tension so the belt can be
    twisted 45 degrees at a point between the camshaft and pump sprockets. Torque
    the tensioner nut to 33 ft. (45 Nm).
  7. Remove the holding tools.
  8. Turn the engine 2 full revolutions to return to TDC of No. 1 piston. Recheck
    belt tension and timing mark alignment, readjust as required.
  9. Install the belt cover and accessory drive belts.
  10. If the belt is too tight, there will be a growling noise that rises and
    falls with engine speed.


prev.gif next.gif

Oct 29, 2010 | Volkswagen Golf Cars & Trucks

2 Answers

Can not get timing 2 set on my daihatsu hijet there is dots on timing cogs which timing belt runs on on front of motor but no markings 2 set them at car will not fire


Click on the following free direct Link. It has the Timing: Belt and Mark Diagrams for the 1988 Daihatsu Charade 1.0L 3-Cylinder which is the closest to the Hijet. Plus additional Instructional and Directional Diagrams.

Note: the annotated Align Matings Marks located on the engine casing, or the Belt Alignment Marks.
I owned one of these while living in Japan.

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

http://www.2carpros.com/car_repair_information/year/1988/make/daihatsu/model/charade/1988_daihatsu_charade_timing_belt_diagram_marks.htm

Apr 02, 2010 | 1988 Daihatsu Charade

2 Answers

TIMING MARKS CAMBELT REPLACEMENT FOR CL-T CHARADE, PLEASE


This is the best I could find for you .. I am unfortunately able to verify the info because I have no personal experience with this car or its engine ...

Mar 14, 2009 | 1988 Daihatsu Charade

1 Answer

Daihatsu hijet 4wd van 1985 model 3 cyl 4 stroke 993cc valv tmg


If the belt has slipped you might be in trouble, becuase it's an interference engine.

e9f5605.jpg

Jan 30, 2009 | 1992 Daihatsu Charade

2 Answers

Driving home my truck quit running


well you didn't specify the year, make, and model of the truck you are asking about so this is the best answer I can come up with. Below is a list I found that says what vehicles are interference motors...

INTERFERENCE ENGINES WITH TIMING BELTS
ACURA
engine_interference.jpg
1986-89 1.6L Integra
1991-95 1.7L Integra
1990-95 1.8L Integra
1986-89 2.5L Legend
1992-94 2.5L Vigor
1986-89 2.7L Legend
1990 2.7L Legend
1991-95 3.0L NSX
1991-95 3.2L Legend
AUDI
1970-93 All Except 1970-77
1.9L & 1970-73 1.8L
BMW
1987-95 2.5L 325I 525I
1994-95 4.0L 740I
CHRYSLER
1993-95 1.5L Colt
1987-88 1.5L Colt
1992-95 1.5L Eagle Summit
1987-88 1.6L Colt
1989-92 1.6L Eagle Summit
1994-98 2.0L Neon Stratus
1990-95 2.0L Eagle Talon
DAIHATSU
1988-92 1.0L Charade
1988-92 1.3L Charade
1990-92 1.6L Rocky
FIAT
1974-79 1.3L 128 Series
1979-82 1.5L Stranda
1974-78 1.6L 124 Series
1974-78 1.8L 124 Series
1974-78 1.8L 131 Series, Brava
1979-82 2.0L Brava, Spider
FORD
1981-85 1.6L Escort, EXP
1981-83 1.6L LN7, Lynx
1984-85 2.0L Escort, Tempo
1993-95 2.0L Probe
1986-88 2.0L Ranger
1984-87 2.0L Lynx, Topaz Diesel
1985 2.2L Ranger
1989-92 2.2L Probe
1986-88 2.3L Ranger
1986-87 2.3L Diesel Ranger
1991-98 4.6L Crown Victoria
GM
1986-95 1.0L Geo Metro
1989-91 1.0L Firefly (CANADA)
1985-88 1.5L Sunburst (CANADA)
1985-89 1.5L Spectrum
1990-93 1.6L Prizm, Storm
1981-84 1.8L Diesel (CANADA)
1982-86 1.8L Buick Skyhawk
1990-98 1.9L Saturn
1987-88 2.0L Buick Skyhawk
1988-95 2.3L Quad Four
1985-87 3.0L Buick
1979-95 3.8L Buick
HONDA
1986-87 1.0L Prelude
1973-78 1.2L All
1973-78 1.3L All
1980-84 1.3L All
1973-78 1.5L All
1985-89 1.5L Civic
1988-95 1.5L Civic, CRX
1993-95 1.5L Civic Del Sol
1979-84 1.5L All
1985-87 1.5L CRX
1993-95 1.6L Civic Del Sol
1973-78 1.6L All
1980-82 1.6L All
1988-95 1.6L Civic, CRX
1984-87 1.8L Prelude, Accord
1979-83 1.8L All
1986-91 2.0L Prelude
1990-91 2.1L Prelude
1990-95 2.2L Prelude, Accord
1992-95 2.2L Prelude
1995 2.7L Accord
HYUNDAI
1984-95 1.5L Excel Scoupe
1995-98 1.5L Accent
1992-95 1.6L Elantra
1993-95 1.8L Elantra
1992-95 2.0L Sonata
1989-91 2.4L Sonata
1990-95 3.0L Sonata
INFINITI
1990-92 3.0L M30
ISUZU
1987-89 1.5L I-Mark
1990-93 1.6L Stylus Impulse
1987-89 2.0L Impulse
1981-87 2.2L Diesel Truck
1986-95 2.3L Truck Trooper
1988-95 2.6L Truck Rodeo Amigo
1991-96 3.2L Trooper Rodeo Amigo
KIA
1995 2.0L Sportage
MAZDA
1984-85 2.0L 626
1988-92 2.2L 626 MX6
1989-93 2.2L Pickup
1988-95 3.0L 929 MPV
MITSUBISHI
1985-95 1.5L Mirage Precise
1990-92 1.6L Mirage
1989-95 2.0L Galant Eclipse
1983-86 2.3L Diesel Pickup
1994-95 2.4L Galant
NISSAN
1982 1.5L Centra
1983-88 1.6L Sentra Pulsar
1987-89 1.8L Pulsar
1982-89 2.0L Stanza 300ZX
1984-95 3.0L Maxima 300ZX Pathfinder
PORSCHE
1976-83 2.0L 924
1976-89 2.5L 944 Series
1989 2.7L 944 Series
1989-91 3.0L 944 Series
1976-83 4.5L 928
1984 4.7L 928
1985-91 5.0L 928
1992-95 5.4L 928
SUZUKI
1985-94 1.3L Samurai Sidekick
1989-94 1.3L Swift
TOYOTA
1986-95 1.5L Tercel
1981-83 2.2L Pickup
1984-87 2.4L Pickup
1982-88 2.8L Celica Cressida
1987-94 3.0L 4-Runner
VOLKSWAGEN
1976-91 All Except 1.9 2.1L Engine
1990-92 1.6L Golf (CANADA) Jetta
1990-95 2.0L GTI Jetta GLI Passat
VOLVO
1991 2.3L Coupe 940
1986-94 2.3L 240 740 940

Jan 30, 2009 | 1994 Nissan Maxima

2 Answers

Need to change a WATER PUMP on my DAIHATSU CHARADE GLXI 1994


The location of the pump is on the left hand side of the engine when standing at the front of the car.
You will see (if you have aircon) two belts.
If you stand to the side of the car to look at the belts.
From memory the inner one (closest to the engine) drives the aircon compressor.
The outer one drives the water pump, you will see the pump belt wheel towards the back of the engine.

Getting into the pump is a bit tricky.
I basically unbolted the engine mount from the body which then allowed me to jack up the engine as I needed it to give me space to unbolt everything until the 3 water pump bolts can be seen.
Just make sure you know which bolts go back where.
From memory there were about 20 bolts to undo before I got to the water pump.

Aircon compressor bracket bolt I only loosened them from the engine not fully removed, the same with the alternator I only removed the adjusting bolt to remove the belt.

Oh I just thought of something to do before you remove the tension on the belts... loosen slightly the 4 small bolts that are on the wheel that bolts onto the water pump.

I think the only size sockets and spanners I used were 10, 12, 14 & 17.

It took me around 2 hours to get it all undone, and close to the same to put it all back together with the new pump.

It was kinda straight forward as you can see what you need to unbolt because you know what bit you need to get into.

I hope this helps a little, I am not sure if it is clear in the way I have written it. But feel free to ask any questions.



Jan 28, 2009 | 1992 Daihatsu Charade

2 Answers

Firing order of a daihatsu charade 3cyl 1995 model


If you find this Info Helpful Please Rate Me as It Helps me to reach the Expertise STATUS that I have Worked 30yrs to get to LoL Thank You Very Much and Have a Great Week!!



Firing Order: 1 - 2 - 3
Base Ignition Timing
Note: With the T terminal Shorted.5 +/- 2 deg BTDC
Ignition timing should be checked and adjusted, if necessary whenever spark plugs are replaced or any distributor maintenance is done. Ignition timing should be 3-7°BTDC at 750-850 RPM with the engine check connector terminal 11 (brown) shorted, Fig. 1. The engine check connector is located near the top of the transaxle.

Jan 21, 2009 | 1992 Daihatsu Charade

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daihatsu Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

74945 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Are you a Daihatsu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...