Question about Mitsubishi Cars & Trucks

Open Question

Do not know location of high beam headlight relay on pajero nt 2009

I want to replace high beam relay

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1861 Answers

SOURCE: Low beam headlights don't work

I have e-mailed you 2 .pdf files, one is the complete headlamp diagram, and the other is the relay locations. Please advise if you need further assistance.

Toyota Ed

Posted on Jan 02, 2009

  • 2 Answers

SOURCE: 1994 Mercedes c280 high beams not working...

At first 1994 C280 high beams began to not connect regularly when stick pushed forward, then not at all. Drove high beams by pulling and holding stick back towards steering wheel until that stopped working, too. Shop said the turn signal switch was at fault-- had seen it many times before with W202; about $160 to replace. Haven't done it yet, but should be an easy fix?

Posted on Jun 24, 2009

  • 87 Answers

SOURCE: Drl and high beams dont work

Check the bulbs -- the daytime running lamps use the highbeams on the resistor -- There are two filliments per bulb one high; one low. If both high beam filliments are out nothing will work....replace bulbs if this is the case.

Posted on Aug 02, 2009

  • 23 Answers

SOURCE: camry headlights not working

Have you checked out the switch itself? Seems like the problem might be there.
If the lamp bulbs are sill intact, that's probably the most likely solution. There's a possibility you have a short somewhere in the switch relay that will allow the highlights to turn on but not the low beams.

Posted on Mar 25, 2010

ftw1952
  • 10319 Answers

SOURCE: The high beam indicator is on. The low beams don't work.

You need a new headlight dimmer switch located on the steering column between the dash and the firewall

Posted on Jun 03, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Why don't my headlights work on my 2009 Mercury Grand Marquis?


Low Beam, and High Beam both are not working? There is a fuse you can check, review your owners manual for location, also could be headlight switch itself? Please check bulbs before expensive diagnosis...some times both bulbs blow out at the same time:( Hope this helps.

Aug 28, 2014 | Cars & Trucks

1 Answer

Where are the headlight relays 1998 chrysler sebring?


Check in that fuse box again. There is one for each, the high beam and the low beam.

Jan 16, 2013 | Cars & Trucks

1 Answer

Location of headlight relay for 1991 ford explorer


The first thing is to make sure the bulbs are good, if the low beam bulbs are bad the high beams will still work, the first thing is to try new bulbs.Replace the bulbs and then let me know the results.Good day.

May 06, 2012 | Ford Explorer Cars & Trucks

1 Answer

Low beam headlights do not work, high beam headlights work


Hello and Welcome to FixYa!
Check for the fuses and relays, located in the Engine/ Driving Compartment.. The fuse/relay for the Headlights will be marked on the casing of the fuse holder. You have to locate that fuse and have to replace it in case of bad/ faulty. Also do make sure, that the Switch that performs the High/Low beam operation is properly working. Worst case scenario would be the bad filament/ projection tube usually called bulb/ beam.

Concerned.

Mar 07, 2011 | 2002 Pontiac Bonneville

1 Answer

Headlights went out. Replaced bulbs and switch and still lights don't work. Fog lights and high beams work? What else can work?


If high beams work and low beams do not, then it is probably the high/low relay. It is part number 15016745 and has four prongs. To test if your relay has gone bad locate the relay in your fuse box. There will be two of these relays located next to each other. One controls the low beam headlights and the other the cooling fan. Swap the relays and check your low beam headlights. If the low beams work you have a bad relay.

Sep 20, 2010 | 2006 GMC Envoy

1 Answer

I have a 2005 dodge caravan. the headlights have


On the van you have a high beam fuse and relay. On the low beam you also have a fuse and relay. Check the fuse/relay panel for a blown fuse controlling the low beam lights. If you do not find a blown fuse have some one to turn the key on and turn on the high beam lights> During this time locate the low beam headlight relay and place your finger on top of relay, have the other person to switch from high beam to low beam lights. You should feel a click in the relay when they make the switch from high to low beam. If not replace the relay and the problem should go away. Hope this will help you.

May 28, 2010 | 2005 Dodge Caravan

1 Answer

No low beam only high beam


check the ground connection of the bulbs. check the light switch. the headlight relay is located under the dash or under the hood.

Nov 25, 2009 | 1994 Mazda 323

1 Answer

Headlights wont work


Fuse 22 and fuse 23 are left and right low beam headlamp fuses located in the PDC. 23 and 24 are high beam fuses. There is also a low beam and a high beam relay in PDC as well. If no headlights work I would check for main switch or multifuction switch (wiper/high beam) since each light has its own fuse and relay.

Jun 05, 2009 | 1997 Dodge Caravan

4 Answers

Headlight main beam not working


Strange headlamp problems on Saabs can often be attributed to a failing Headlamp relay. Here are a few common situations:
Issue1 - Headlamp switch will work backwards: Turn on the switch and theheadlights go off and turn off the switch and the headlights will goon.
Issue 2 - High beams will disappear. You will have nohighbeams. Be sure to check the headlight bulbs PRIOR to ordering therelay. Remember however that it is possible for both high beams burn out at the same time
Issue3 - High beams will not work only the low beams will.
Issue 4 - A single bulb setting (low or high) on either side will not work and bulb replacement will fix it.
You can sometimesfix these issues by removing the relay, taking off the cover andresoldering the connections on the relay bottom. To perform this repair, go to my illustrated tutorial at customsaab.com.
In some cases youwill have to replace the relay to effect a long term cure. The aftermarket replacement can be had at Eeuroparts.com for about $60.00:
Name: Bulb Check Relay
Part Code: 4109070A
Brand: sm_311e0dbd-c670-4bed-a50a-1ba3424ef87d.jpg
Description: Bulb check relay for any 9000 92-98, 900 94-98, 9-3 99-03, 9-5 all.

KAE (Kaehler) made in Germany.
Price: $59.90


Nov 19, 2008 | 1999 Saab 9-5

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...