Question about GMC Sierra
All dash light dome light radieo everything goes out when key is in start position until key is returned to run pos.
Everything is supposed to go off in the start position. You would have power to the engine computer and other components to start.
If the engine is not locked up, it could be the starter or a bad connection with one of the battery cables.
Posted on Feb 13, 2014
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
on my 2004 ram 2500, I had to depress the trip odometer button and turn on the Ignition. all lights on instrument panel will illuminate, continue to hold button in and tach/speedomenter will run full up and back down. once this has completed, the obd codes will be shown in the odometer.
Posted on Jan 09, 2009
SOURCE: My 2000 Ford Expedition has
If it is a single click, the problem lies in the starter solenoid or relay. If it is several clicks in succession, the battery may be low or there may be a loose cable.
also try this :-- Please make sure the battery is fully charged before doing this test! Also make sure all the connections on the starter, battery and cable ends are tight and clean! this is important!! This won't be fun to test but it will tell you if the starter is good or not. Crawl under the car. (Make sure you use the proper jacks and jack stands!) find the end of the starter (not the end that is attached to the bell housing) and find the solenoid switch. it should have 3 bolts on it. Two large ones and a small one. The top large wire should be the positive battery cable, the bottom large wire should go into the starter and the small wire should be from the ignition switch. Take a wire and hold it to the top large wire on the solenoid. (be careful of the other end of that wire when you have it connected to the top large wire of the solenoid! don't ground this wire. it will turn out badly. take the other end of the wire and touch it to the small bolt on the solenoid end. If the starter is working, the solenoid should engage and the starter will turn. If this happens it is most likely the ignition switch. If the starter doesn't turn, the starter could be bad.
Starter Relay Test
Place transmission in Park.
Apply parking brake.
Check for battery voltage between starter relay battery terminal and ground.
Connect jumper wire on starter relay between battery and ignition terminals.
If engine does not crank, connect a second jumper wire to starter relay between ground terminal and good ground and repeat test.
If engine cranks in step 3, transmission linkage is misadjusted or neutral safety switch is defective.
If engine does not crank in step 3, starter relay is defective.
Follow this step by step and you will pinpoint the problem.
This will help. Thanks please keep updated.please do rate the solution positively .thank you for using fixya.
Posted on Oct 24, 2009
Tips for a great answer:
Oct 11, 2015 | Cars & Trucks
May 03, 2015 | 2006 Nissan Xterra
Mar 12, 2017 | Toyota Corolla Cars & Trucks
Jul 05, 2013 | 1993 Chevrolet Corsica
Sep 25, 2010 | 2002 Chrysler Sebring
Jul 21, 2010 | 2004 Chevrolet Cavalier
Mar 07, 2010 | 1996 Chevrolet C1500
Sep 29, 2009 | 2002 Buick Rendezvous
Feb 06, 2009 | 2004 Mitsubishi Endeavor
Jan 15, 2009 | 2004 Ford Expedition
Oct 15, 2017 | GMC Cars & Trucks
134 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: