Question about Buick Park Avenue

Open Question

Brake pedal goes all the way to the floor

Pads and calipers have been replaced . blead brake line and cant get them tight .

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1779 Answers

SOURCE: Just replaced the calipers and

Did you bleed the wheel furthest away from the master cylinder? THen next furthest, to closest last. Did u make sure the master cylinder never got low enough to draw in air? To bleed, Pumo brakes 3x, holding pedal down 1/2 way, while bleeder is opened, let air/fluid flow, shut bleeder as flow diminishes so no air gets in the line. Is the car running when u bleed brakes? It should be. If u are doing all of this u should feel your pedal coming back (getting firm). Let me know how you make out. countrycurt0

Posted on Sep 21, 2008

Ad
  • 7 Answers

SOURCE: 2001 Mustang GT rear brake job

yep this is a two man job, onece you get air in the lines is better to do all four, my has abs and i was able to do it, but next time don't take anylines lose just turn the piston clockwise and you should be able to push it in.

Posted on Oct 12, 2008

emissionwiz
  • 76848 Answers

SOURCE: brake pedal dropping to floor

do u have the antilock brake bleeding tool? if not you will need to have the dealer bleed the brakes, the ABS control valve must be electricaly held open to bleed the brakes there of course is a special tool for this.

Posted on Oct 18, 2009

Testimonial: "Thank You"

  • 12 Answers

SOURCE: brake pedal goes to the floor

check vacumn and\or connections to the vacumn boost cannister.

Posted on Apr 21, 2010

alicantecoli
  • 22246 Answers

SOURCE: Replace all brakes pads and shoes also calipers on

put a brick on the brake pedal and leave overnight ,see what happens

Posted on Jul 24, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Pedal going to floor


You have drums in the back? Pretty sure you do. These need adjusted out to fit the drum. Or replace the drums. and adjust to fit. Old drums will have a lip to go over. Usually rust.. some metal.

Sep 03, 2014 | 1979 Chevrolet Camaro

1 Answer

What are the proper steps to bleeding your brakes on a 1990 vw golf deisel


For left hand drive vehicles: (If the car does not have ABS system you do not need any diagnostic equipment!)

IMPORTANT NOTE: You need using diagnostic equipment connected to the data link connector of the car in order to bleed the ABS block. Follow instructions by scantool equipment for bleeding the ABS block.


1. This bleeding procedure requires two people. Remove the brake system reservoir cap, and fill up with new brake fluid until "MAX" level is reached.
2. Lift the car, or use a channel for access under vehicle.
3. Put the gearbox in "N" - Neutral position, or in "P" - Parking position for automatic transmission.
4. Start the engine and push the brake pedal firmly for 4 - 5 times to the floor, and maintain the brake pedal pushed to the floor.
5. Begin with the rear right wheel. Another person remove the dust cap and loose the brake caliper bleeding screw until the brake pedal goes to the floor. At this moment maintain the brake pedal pushed to the floor, engine idling, and tight the brake caliper bleeding screw. Use a plastic hose: one end connected to the brake caliper bleeding screw, and another end inside a recovery bottle for used brake fluid.
6. Repeat steps no.#4 and no.#5 until no air flows through the brake caliper bleeding screw. Tight the brake caliper bleeding screw, and put the dust cap in their place.

IMPORTANT NOTE: All the time check the brake fluid level in the brake system reservoir, and fill up if necessary!

7. Push the brake pedal firmly for 4 - 5 times to the floor, and maintain the brake pedal pushed to the floor, engine idling.
8. Continue with the rear left wheel. Another person remove the dust cap and loose the brake caliper bleeding screw until the brake pedal goes to the floor. At this moment maintain the brake pedal pushed to the floor, engine idling, and tight the brake caliper bleeding screw. Use a plastic hose: one end connected to the brake caliper bleeding screw, and another end inside a recovery bottle for used brake fluid.
9. Repeat steps no.#7 and no.#8 until no air flows through the brake caliper bleeding screw. Tight the brake caliper bleeding screw, and put the dust cap in their place.

IMPORTANT NOTE: All the time check the brake fluid level in the brake system reservoir, and fill up if necessary!

10. Push the brake pedal firmly for 4 - 5 times to the floor, and maintain the brake pedal pushed to the floor, engine idling.
11. Continue with the front right wheel. Another person remove the dust cap and loose the brake caliper bleeding screw until the brake pedal goes to the floor. At this moment maintain the brake pedal pushed to the floor, engine idling, and tight the brake caliper bleeding screw. Use a plastic hose: one end connected to the brake caliper bleeding screw, and another end inside a recovery bottle for used brake fluid.
12. Repeat steps no.#10 and no.#11 until no air flows through the brake caliper bleeding screw. Tight the brake caliper bleeding screw, and put the dust cap in their place.

IMPORTANT NOTE: All the time check the brake fluid level in the brake system reservoir, and fill up if necessary!

13. Push the brake pedal firmly for 4 - 5 times to the floor, and maintain the brake pedal pushed to the floor, engine idling.
14. Continue with the front left wheel. Another person remove the dust cap and loose the brake caliper bleeding screw until the brake pedal goes to the floor. At this moment maintain the brake pedal pushed to the floor, engine idling, and tight the brake caliper bleeding screw. Use a plastic hose: one end connected to the brake caliper bleeding screw, and another end inside a recovery bottle for used brake fluid.
15. Repeat steps no.#13 and no.#14 until no air flows through the brake caliper bleeding screw. Tight the brake caliper bleeding screw, and put the dust cap in their place.
16. Now the brakes are bleeded. Check the brake fluid level in the reservoir. Fill up with new brake fluid until "MAX" level is reached. Put back the brake reservoir cap.
17. Test the car brake system. The brake pedal movement no more than 1/3 of total stroke until the floor, when brake pedal is applied. Maximum admissible is 1/2 of total stroke.

Dec 06, 2010 | Volkswagen Golf Cars & Trucks

1 Answer

I have a 96 silverado with abs, a friend owed me some money so i told him to put new front brake pads and get the front rotors and rear drums turned, he finshed the job and called me and said my brakes are...


PRe bleed the master cylinder, using a kit that hooks up to the brake lines connection and the other end goes into the fluid reservoir. Bleed until no bubbles. then reinstall brake lines, one at a time, and then continue bleeding the system. DO NOT let the fluid run low in M/C or start all over again. Kit can be purchased at after market parts stores.

Oct 09, 2010 | Chevrolet 1500 Cars & Trucks

1 Answer

How do you adjust the rear brakes on a 2003 kia spectra? It feels like you have to push the break pedals down to the floor in order for the car to stop. They seem to need tightening, but there doesn't seem...


The rear brakes on the Spectra will always engage less than the front brakes. If you have to push hard on the brake pedal then you probably have air in the brake lines from the last brake pad replacement. The brakes need to be bled with this method: Use 1/8 inch 2 foot long hose from parts store and attach from bleeder valve ball on the brake caliper to a bottle partially filled with brake fluid. End of hose should be submerged in bottle. With second person holding brake pedal to floor, slowly turn bleeder valve counter clockwise (loosen tiny bit) with wrench and watch for dirty brake fluid to create bubbles in the bottle. When bubbles start, quickly tighten bleeder valve back to tight. Second person lifts foot while valve is tight and then pushes pedal to floor again and THEN you again open bleeder valve slowly turning counter clockwise and watch for bubbles. Repeat until no more bubbles can be created in the bottle where the hose is submerged. Move to next caliper and repeat. For a firm brake pedal you will need to repeat this on all four calipers. My 2003 Kia's rear brake pads "fell apart" and never wore out in 190000 miles because they do not get used. The braking power is primarily in the front disk brakes on this model. Removing and replacing the rear drum brake linings did not even require me to bleed the brake lines. They weren't that tight before or after the replacement procedure.

Jul 24, 2010 | 2003 Kia Spectra

1 Answer

Brake petal goes to floor


if you cant find any leaks in lines or cylinders or calipers u probaly have a bad booster
see lots come threw my shop like that but also their is a vacum line that runs to the booster and it hooks to a plastic valve that goes in to the booster those get gloged and you loose pedal as well try replacing that before you bye a new boooster

Mar 26, 2009 | 2000 Jeep Grand Cherokee

2 Answers

Changed front brake pads. brake pedal goes to floor. no brakes


Something doesn't sound right, you shouldn't have to remove the brake line to install pads. Did you have to do this on both sides? Do the new pads and the old pads look the same? Did you get the caliper on crooked? Just recheck your work first before replacing more parts. When you install the caliper, You have to hook the pad on one side first before you slide it over the rotor.

Mar 26, 2009 | 2000 Jeep Grand Cherokee

2 Answers

Just replaced the calipers and blead the brakes. Pedal still travels clear to the floor.


Did you bleed the wheel furthest away from the master cylinder? THen next furthest, to closest last. Did u make sure the master cylinder never got low enough to draw in air? To bleed, Pumo brakes 3x, holding pedal down 1/2 way, while bleeder is opened, let air/fluid flow, shut bleeder as flow diminishes so no air gets in the line. Is the car running when u bleed brakes? It should be. If u are doing all of this u should feel your pedal coming back (getting firm). Let me know how you make out. countrycurt0

Sep 21, 2008 | 1998 Mercury Mystique

2 Answers

97 ford e350 brake pedal goes to the floor...


are your rear drums set up? why did you bleed the brakes. when only when you installed new pads?

Sep 11, 2008 | 2002 Ford E350

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

11 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...