Question about Isuzu Rodeo

Open Question

How do you remove the back cover of 2013 Hino side mirror? Is it held by anything or just use flat screw driver and pry off?

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: replace rear turn signal bulb on 2007 H3 - driver side

1st::Unscrew the 2 screws that hold the light in.
2nd::Slide your hand behind the light and pull the light towards you. Make sure that you pull it straight, as if the h3 was driving away from you, so you dont break the two pins that are holding the light in...PULL ONE PIN AT A TIME!!!

Dont pull it to far away from the hummer as there are wires attached that need to stay attached.

3rd::turn the back of the bulb to unlock it from the lens...
4th:: slide the bulb out and remove thebulb by pulling it straight out.
5th::put the new bulb in, lock it back into the lens, then insert it back where you got it from,...

MAKE SURE you move the wires out of the way when you put the lens back in...they will get in the way and can be damaged.

Posted on Apr 07, 2009

Ad
  • 13 Answers

SOURCE: how do i remove and replace the driver's side mirror?

If the metal pivot arm is not broken you can just replace the glass and plastic housing. To remove the glass you tilt the glass down towards the floor and use a wide plastic or wood bladed object to prise from behind, the glass should pop off from its clips. Remember to catch it if its not damaged. To remove the housing once the glass is out you need to look underneath the mirror unit, there you will find a small plastic bung, gently prise it out and then use a long small flat bladed screwdriver straight up inside the hole and lever towards the front of the car whilst lifting straight up on the plastic housing, this should then lift off. To replace just slot the new housing on and click into place then fit the glass back, remember to connect the wires first if it is a heated glass.
If the metal pivot arm is broken then you will find the remaining screws behind the plastic trim inside the vehicle.

Posted on Apr 10, 2009

raffaiel
  • 209 Answers

SOURCE: drivers side mirror needs replaced - how do i remove the little panel inside without breaking anything I shouldn't

just use a flat screw driver to take it off, it just have a clip inside.

Posted on Apr 21, 2009

  • 1 Answer

SOURCE: replacing side view mirror cover on 200 SAAB 9-5

I need a complete passenger Side Mirror (2nd Hand) N-95 (S Reg) contact 07966 366195

Posted on Jul 21, 2009

  • 1986 Answers

SOURCE: How do I remove the cover over the fog light to

You change it from the front of the car.

To remove the fog light - firmly grasp the black plastic lens protector along the outer edges and twist it to the left (counter-clockwise) to remove it.
Now remove the two bolts just above the fog light - the whole thing comes out as an assembly. Then you can disconnect the socket from the back of the assembly

Posted on Oct 21, 2009

Testimonial: "excellent!"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The eazy way to take off a driver side door pannel from 2004 chevy tahoe


The easy way? Goliath it- just rip it off !
Panels are held by several screws and plastic push pins. The screws may be covered by little rectangular snap covers. Pry off the covers to access the screws. One screw should be behind the inner door handle, holding a piece of trim there. Radio speakers are held on by screws, and so might be the trim piece over the speaker. Remove all screws first, check carefully for any hidden ones. Door pulls or armrests may have larger screws holding them fast. The plastic pins are usually around the lower perimeter and up along the sides. Slip a putty knife or thin screwdriver behind the panel and near each pin to pop them out of the frame. Check for anything else holding the panel, like outside mirror screws that go through the panel. When you have the panel all loose, lift out and up from the bottom to clear the window channel. Unplug electrical connections and panel should be free. The plastic water shield is held to door frame by adhesive. Peel it off and save for reapplying. Without that plastic sheet, moisture can get to electrical connections, and mold can start ruining the inside of the door panel.

Aug 14, 2013 | 2005 Chevrolet Tahoe

2 Answers

How to replace driver side mirror on 1999 GMC Jimmy. Just need steps for removing old one and can take it from there. Thanks!


if there is a plastic cover directly behind the mirror on the inside of the car it should come off by gently prying it with a flat blade or screwdriver around the edge of it as most are held on by plastic clips.
Once it is removed it will expose the nuts or bolts that hold the mirror to the door but dont forget to remove the electric wire plug that leads to the mirror

Jun 09, 2010 | 1999 GMC Jimmy

1 Answer

Install motor/regulator to 2000 camry solara


It easy ! You need a philips2_bing.gif and flat screw driver,8" X 4" block of wood and a needle nose pliar.
Use flat screw driver and pry out the two or three dust covers for the arm rest screws then use philips and remove the screws. Next use the flat screw driver and pry out the black plastic mirror cover from the inside of the door. Pry out the switch panel ( aka master switch panel) with the flat screw driver and disconnect it. On the side of the door panel just above the striker is this plastic push pull typeof a hold in screw. Use flat screw driver to get it to move a little then pull it out with the needle nose. Depending on which door your doing if you have a map folder ( driver or front passenger door) in the door there are two more screw to remove on the bottom of the door.
Now the inside door handle is tricky it comes out in two pieces. Use philips and get the only hold down screw you see out.( you may have to pry out al ittle screw cover first) Now the handle cover is removed by placeing the flat screw driver on the rear of the outside of the cover top and on the outside rear bottom to release the tangs that are holding it onto the panel.Pry it out lightly you may have to place the screw driver over the top of the door release button and pry that way. Don't loose your cool its a pain but it will fall out. Once its removed unhook the panel.

Next lift the plastic cover and remove the six gold2_bing.gif bolts first(For motor and regulator) Then push the window down till you see the two bolts holding the window to the regulator .Remove them, BEFORE YOU PULL OUT THE MOTOR AND REGULATOR YOU WILL SEE TWO TANGS THAT HELP HOLD THE REGULATOR AND MOTOR TO THE DOOR MARK THE RELOCATION , NOW pull out the motor and regulator have an assistant hold up the glass while you place the two blocks of wood to hold up the window. Now order your regulator and installation is in reverse. Good luck kate. Keep me posted.
Comments:

Apr 21, 2010 | 2000 Toyota Camry Solara

1 Answer

How do you change the driver side windows motor


This procedure is for both regulator and motor You take them out as a unit then once there out there are three torque screws that seperate the motor from the regulator.It easy ! You need a philips2_bing.gif and flat screw driver,6" X 2" block of wood and a needle nose pliar.
Use flat screw driver and pry out the two or three dust covers for the arm rest screws then use philips and remove the screws. Next use the flat screw driver and pry out the black plastic mirror cover from the inside of the door. Pry out the switch with the flat screw driver and disconnect it. On the side of the door panel just above the striker is this plastic push pull typeof a hold in screw. Use flat screw driver to get it to move a little then pull it out with the needle nose. Depending on which door your doing if you have a map folder in the door there are two more screw to remove on the bottom of the door.
Now the inside door handle is tricky it comes out in two pieces. Use philips and get the only hold down screw you see out.( you may have to pry out al ittle screw cover first) Now the handle cover is removed by placeing the flat screw driver on the rear of the outside of the cover top and on the outside rear bottom to release the tangs that are holding it onto the panel.Pry it out lightly you may have to place the screw driver over the top of the door release button and pry that way. Don't loose your cool its a pain but it will fall out. Once its removed unhook the panel.

Next lift the plastic cover and remove the six gold2_bing.gif bolts first(For motor and regulator) Then push the window down till you see the two bolts holding the window to the regulator .Remove them, BEFORE YOU PULL OUT THE MOTOR AND REGULATOR YOU WILL SEE TWO TANGS THAT HELP HOLD THE REGULATOR AND MOTOR TO THE DOOR MARK THE RELOCATION , NOW pull out the motor and regulator have an assistant hold up the glass while you place the two blocks of wood to hold up the window. Now order your regulator and installation is in reverse. Good luck kate. Keep me posted.

Comments:

Apr 01, 2010 | 2000 Toyota Camry

1 Answer

Driver side door handle (outside) and gas pedal 2000 Camry


Bring the vehicle into the dealer if you have a sticky gas pedal. This is a TOYOTA PROBLEM.
Door handle:
It easy ! You need a philips2_bing.gif and flat screw driver,and a needle nose pliar.
Use flat screw driver and pry out the two or three dust covers for the arm rest screws then use philips and remove the screws. Next use the flat screw driver and pry out the black plastic mirror cover from the inside of the door. Pry out the switch with the flat screw driver and disconnect it. On the side of the door panel just above the striker/loch mechanism is this plastic push pull type of a hold in screw. Use flat screw driver to get it to move a little then pull it out with the needle nose. Depending on which door your doing if you have a map folder in the door there are two more screw to remove on the bottom of the door.
Now the inside door handle is tricky it comes out in TWO pieces. Use philips and get the only hold down screw you see out.( you may have to pry out a little screw cover first) Now the inside door handle cover is removed by placeing the flat screw driver on the rear of the outside of the cover top and on the outside rear bottom to release the tangs that are holding it onto the panel.Pry it out lightly you may have to place the screw driver over the top of the door release button and pry that way. Don't loose your cool its a pain but it will fall out. Once its removed unhook the panel.

Next lift the plastic cover and remove the door handle hooks and levers . Basically use common sense this is easy stuff. There may be two screws from inside of door panel that keep handle in place . Then work handle loose from outside and inside . reverse for installation.

Jan 27, 2010 | 2000 Toyota Camry

1 Answer

Best way to removed driver side door


I have a 1994 Grand Caravan and have done this several times.
1. Disconnect Negative side of Battery.
2. Remove all screws.
a. There are screw covers to remove first before
gaining access to the screws. I use a pick
driver.
b. One in recess of the door arm rest. Round
Cover.
c. One is behind the door latch release. Pull/Hold
open to gain access. Then remove the cover
d. Two are located on the Map pocket. Round
Covers.
e. One is located up near the side mirror.
f. One is located on the upper portion on the door
handle. It has a square cover.
3. Pry up and out the window/mirror adjustment cover and unplug the connection.
4. Use a wide flat screw driver to carefully pry on the bottom then side edges of the trim panel to "pop" the retainers out of the door.
5. Once all retainers have been freed: Lift up the door trim up off the upper ledge.
6. Peel back (but do not entirely remove) the rubber/plastic watershield cover.
7. Disconnect all wire connections to the door trim.
8. Pry off the plastic retaining clip to the door handle metal bar and remove the "L" bar out of the plastic connector.
9. Set the Trim Panel off to the side.
10. Remove all wire holders from the door.
11. Move the wires inside and towards the front lower access hole.
12. Peel back the rubber wire guard between the door and the A-pillar frame.
13. Pull out as much wire as possible out of the door and let hang..
14. While someone else is supporting the door: (If no one can help: with the door fully open: use a jack and block of wood to support the bottom outer edge of the door
a. I use a Breaker Bar or long Wrench
Extention and Hammer or Mallet.
b. Tap Up the Bottom Hinge Pin first.
c. I also use a flat Screw to tap up the Pin Head.
d. Remove the Bottom Door Hinge Pin.
e. Remove the Upper Hinge Pin the same way.
f. Make sure the Door is being held in place.
15. Remove any left over wires out from the door.
16. Carefully move the door away from the hinges.
Good Luck!!
If you have not replaced the Hinge Pins, and Guides, now would be a good time to do it!!

Nov 14, 2009 | 1994 Dodge Caravan

1 Answer

The electric window has come off the runner, how do I get the door lining off to fix it? Kate


It easy ! You need a philips and flat screw driver,6" X 2" block of wood and a needle nose pliar.
Use flat screw driver and pry out the two or three dust covers for the arm rest screws then use philips and remove the screws. Next use the flat screw driver and pry out the black plastic mirror cover from the inside of the door. Pry out the switch with the flat screw driver and disconnect it. On the side of the door panel just above the striker is this plastic push pull typeof a hold in screw. Use flat screw driver to get it to move a little then pull it out with the needle nose. Depending on which door your doing if you have a map folder in the door there are two more screw to remove on the bottom of the door.
Now the inside door handle is tricky it comes out in two pieces. Use philips and get the only hold down screw you see out.( you may have to pry out al ittle screw cover first) Now the handle cover is removed by placeing the flat screw driver on the rear of the outside of the cover top and on the outside rear bottom to release the tangs that are holding it onto the panel.Pry it out lightly you may have to place the screw driver over the top of the door release button and pry that way. Don't loose your cool its a pain but it will fall out. Once its removed unhook the panel.

Next lift the plastic cover and remove the six gold bolts first(For motor and regulator) Then push the window down till you see the two bolts holding the window to the regulator .Remove them, BEFORE YOU PULL OUT THE MOTOR AND REGULATOR YOU WILL SEE TWO TANGS THAT HELP HOLD THE REGULATOR AND MOTOR TO THE DOOR MARK THE RELOCATION , NOW pull out the motor and regulator have an assistant hold up the glass while you place the two blocks of wood to hold up the window. Now order your regulator and installation is in reverse. Good luck kate. Keep me posted.

Oct 10, 2009 | 2000 Toyota Camry

1 Answer

Had a little booboo


ok, there is a triangle shaped cover on the inside of the door opposite of the mirror. use a butter knife or similar tool ( flat screw driver) and pry the cover off, it is held in by 2 clips. with that removed you will see the 2 nuts that hold the mirror on (there may be foam insulation covering the nuts). if yours is power then disconnect the connector first then remove the 2 retaining nuts. make sure to hold the old mirror or it could fall after you take the nuts out. install new one in reverse order. viola! good as new!

Feb 21, 2009 | 2002 GMC Yukon Denali

1 Answer

Replacing driver's side mirror on Kia Sorento


These instructions are for a 2013 Kia Sorento (Passenger Side Mirror)



1) remove speaker cover on inside door panel:



3_18_2013_2_40_43_pm.jpg
2) Use a small screwdriver to pry it away from the door. Be careful of the paint:
3_18_2013_2_41_45_pm.jpg

3) The panel will expose the 3 main bolts that need to be removed:
3_18_2013_2_43_24_pm.jpg

4) The cable harness needs to be removed this is located behind the door panel. Remove the one screw behind the screw cover:
3_18_2013_2_44_56_pm.jpg3_18_2013_2_45_02_pm.jpg3_18_2013_2_45_08_pm.jpg

Once the one screw is removed it will allow you to move the door panel enough to get to the harness and the 2 bottom bolts.

Here is how the harness looks:



3_18_2013_2_46_36_pm.jpg
Once the harness is removed and the 3 bolts removed the mirror will come out.

Repeat the steps to re install your new mirror.

Dec 25, 2008 | 2004 Kia Sorento

2 Answers

Door panel removal


I replaced the passenger side mirror on my 1998 Bonneville.
(Thanks to VWmechanic for his helpful post re a 1997 Bonneville; my '98 was a little different.)
First, remove the door panel, as follows:
1. Remove hex-head screw under inside door handle.
2. Remove 10mm screw located under armrest hand grip (to get at it, pop off the piece that covers the tiny courtesy light)
3. Using a screwdriver, pry off the panel. It's held on by several plastic, pop-off fasteners.
4. Remove the plastic red lock slider under the door handle. It can be pried off the wire slider.
5. Lift up on the door panel to release the top edge. You now have access to the inside of the door.
6. To get at the two bolts holding the mirror to the sheet metal of the fender, remove the plastic shield just under the bolt location.
7. Remove/fasten the mirror bolts with a 10mm. I could reach the front bolt with an 8" socket extension, but had to use a 10mm open wrench on the back bolt.


May 28, 2008 | 1997 Pontiac Bonneville

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

140 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14381 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...