Question about Cars & Trucks

Open Question

Oil level on yamaha moto 4 1986 225cc - Cars & Trucks

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1992 Yamaha MOTO 4 won't idle when in gear when you put it into reverse it starts driving straight away


There is a problem with to clutch system. It might be as little as to adjust the clutch settings - up to complete overhaul of the clutch system. Try adjusting it first by increasing the pull of the clutch lever.

Oct 19, 2016 | Yamaha Cars & Trucks

1 Answer

I have an yamaha libero and while riding for sometime the bike stop and again not restarting. why?


Hi Biju:
I would start by checking the basics.
1) confirm batter condition if electric start, oil level
2) Remove spark plug, check condition and spark. Should be hot and blue. If no spark, track down electrical problem. If plug is wet, indicates gas getting into cylinder. If dry, look for fuel delivery problem. Plugged filter? gummed up carb? Water in fuel?
Reply as a comment to this post if you wish to discuss more.
Cheers.

Dec 08, 2015 | Cars & Trucks

1 Answer

How many Quart of oil includ filter oil change


five litres , -- pour 4 litres of oil, let them go till sump, then take the oil dip stick after 5 minutes to check the level then pour the remaining oil. the oil dipstick contains two level indicator, low level and maximum level - low level contains minimum 3 litres but between the low level and the maximum level it is only 3 litres maximum. Hope this may be enough suggestion - Raj / India / scanacar@gmail.com

Jul 05, 2014 | 2003 Toyota Corolla

1 Answer

Just bought a 2006 Crossfire. The area where the (Trip Milage) is, a beep then the Oil Logo with the word HI comes on once a day at least. The Manual says the Oil has too much and the oil pan needs to be...


Yes its mentioned correct in manual.The HI indication comes on when there is about 1 quart too much oil. Get the excess oil drained.----------- CHECKING ENGINE OIL LEVEL:-------- A sensor in the oil pan allows oil level to be checked
without opening the hood. It provides an accurate measurement of oil level, whereas the low engine oil level indicator warns that oil level is definitely too low. With the vehicle parked on a level surface, the engine is warmed up and shut off for approximately five minutes.When the ignition switch is turned to the ON/RUN position, an ISO oil level icon appears in the trip odometer window and a "clock" icon in the cumulative odometer display. Pressing the knob to the left of the speedometer twice within one second displays one of the following messages:
• OK
• -1.0 Q (-1.0L)
• -1.5 Q (-1.5L)
• -2.0 Q (-2.0L)
• HI
The indicated amount of oil must be added to the engine
if the message -2.0 Q (-2.0L) blinks and a signal sounds.
The HI message indicates that the excess oil must be
removed from the pan to avoid possible engine or
catalytic converter damage. If the ISO oil level icon and
"clock" icon remain on when attempting to check oil
level and no message follows, or if the low engine oil
level warning lamp comes on, a malfunction in the
engine oil level system is indicated. A conveniently
located dipstick allows manual checking of the oil level.
If no leaks are noted, continue to drive to the nearest
service station where the engine oil should be topped to
the "full" mark on the dipstick with an approved oil.--------------------

Apr 09, 2011 | Chrysler Crossfire Cars & Trucks

1 Answer

Where is the transmission dipstick in my manual 1.3 liter 1993 suzuki swift located and where do i fill it up?


LEVEL CHECK With Oil Level Gauge Fig. 1: Manual transaxle oil level check - with level gauge 84241046.gif
  1. Drive the vehicle to bring the transmission up to operating temperature.
  2. With the engine stopped, remove the oil level gauge front the side case of the transaxle.
  3. Check the color and smell of the oil. If it is black in color or smells burnt, further transmission service is needed.
  4. Wipe off oil level gauge with clean cloth.
  5. Fit the oil level gauge to the transaxle side case so that the threads rest on top of the case.
  6. Remove the gauge and check oil level. The level should be between FULL and LOW level line.
  7. If the level is below LOW mark, add oil until the proper level is reached.
With Oil Level/Filler Plug
  1. Drive the vehicle to bring the transmission up to operating temperature.
  2. Raise and support the vehicle safely.
  3. Remove the transaxle oil level/filler plug.
  4. Check the color and smell of the oil. If it is black in color or smells burnt, further transmission service is needed.
  5. Transaxle oil level should be even with the bottom of the plug hole. If oil level is low, adjust oil level accordingly.
  6. Install transaxle oil level/filler plug and tighten to 40 ft. lbs. (54 Nm).
  7. Lower the vehicle.

Oct 17, 2010 | 1993 Suzuki Swift

3 Answers

Oil level indicator fluctuates but has oil


it a common defect in the cluster it self another common problem is temp gage also 2 bars up 2 bars ..

May 27, 2009 | 1994 Lincoln Continental

1 Answer

Trying to add correct volume of oil


there is an oil site glass on the trans case, the oil will not cover the gears, the oil level should be at the 1/2 way point of the site glass window.

May 03, 2009 | Honda Accord Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

11 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...