Question about 2007 Saturn Aura XR Sedan

Open Question

How 2 fitted fan belt tensioner 1-9 dti scenic

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi, how many marks does a timing belt of a renault scenic dti have


none - the timing marks are on the pulleys and line up with marks in the head or block or each other .

Sep 14, 2015 | Renault Cars & Trucks

1 Answer

Fan belt squeeling


Fan belts (i assume you are using a v belt and not a serpentine --Flat belt) come in several widths. The correct belt should be level with thw outside dia of all the pulleys or just a bit higher. IF it sits down in the groove it is the wrong belt.. If you have a flat belt ensure you have it fitted correctly around all the pulleys and tensioner otherwise the tensioner won't work as designed to

Mar 03, 2013 | 2002 Ford Focus

1 Answer

Installing water pump in 97 cavalier 2.2


Hi. Here's the proceudere on how to replace the water pump of your 97 Chevy Cavalier.


•1
Drain the cooling system. Place a large oil drain container under the drain fitting located on the bottom of the radiator. Turn the drain fitting counterclockwise until fluid is draining from the radiator. Use a pair of pliers to turn the drain fitting if you cannot turn it by hand. Turn the fitting clockwise to tighten it after all of the fluid has drained from the radiator.
•2
Remove the cooling fan. Disconnect the electrical connection from the fan motor. Remove the bolts holding the fan assembly to the radiator support with a ratchet wrench. Pull the fan assembly up from the engine compartment and remove it.
•3
Remove the serpentine belt. Place a wrench over the belt tensioner and rotate the tensioner to release the tension on the belt. Pull the belt off the pulleys and remove it from the vehicle.
•4
Remove the water pump pulley. Place a screwdriver behind the pulley to lock it in place while removing the pulley mounting bolts with a ratchet wrench.
•5
Disconnect the coolant hoses running to the water pump.
•6
Remove the water pump mounting bolts with a ratchet wrench or wrench and remove the water pump from the vehicle.
•7
Clean the mating surfaces of the engine block and new water pump with a towel saturated with lacquer thinner.
•8
Apply a thin layer of RTV sealer to both sides of the new water pump gasket and place the gasket on the new water pump.
•9
Place the water pump against the engine block and finger tighten the water pump mounting bolts to hold the pump in place. Tighten the bolts with a torque wrench to 18 foot-pounds.
•10
Place the pulley on the water pump and install the water pump pulley mounting bolts with a ratchet wrench.
•11
Attach any hoses previously disconnected from the water pump.
•12
Install the serpentine belt. Route the belt over the pulleys according to the routing diagram in the engine compartment. Place a wrench over the belt tensioner and rotate the tensioner to tighten the tension on the belt.
•13
Install the cooling fan. Gently lower the cooling fan in position and install the mounting bolts attaching the fan assembly to the radiator support with a ratchet wrench. Attach the electrical connection to the fan motor.
•14
Refill the cooling system to the appropriate level, start the vehicle and check for leaks around the water pump.

All the best!

Nov 10, 2010 | 1997 Chevrolet Cavalier

1 Answer

Alternator belt broken


Audi A6 (1999 fabrication year):
1. Release the fan belt tensioner.
2. Remove the broken belt.
3. Put the new belt correctly in place.
4. Set-up the fan belt tensioner.

If you specify the engine type of yours car I will send you the fan belt routing diagram!

Apr 07, 2010 | 1999 Audi A6

2 Answers

Hi we have a kia sedona 2000year and 2.9 diesel, exec. auto. it came with half the engine in the boot, we have skimed the head and rebuilt it just the new cam belt just wont tighten enough we have fully...


the cam belt should have a little slack in it,, about 1/2 inch over its longest run, its not like a fan belt witch should be tight, but check the idler bearing are not worn out,,and i do hope this is a new belt for this car,,,if your using the old belt,,,dont! fit a new one on it or it could brake on you, and that would be another engine rebuild on your hands,,,
,

Mar 07, 2010 | 2003 Kia Sedona

1 Answer

Loss of power


Yes, or an air leak, have you been back to the garage who serviced it?

Oct 23, 2009 | 2000 Renault 181

1 Answer

How do i change a serpentine belt for a 2007


Drive Belt: Service and Repair
DRIVE BELT

Components
43931e7.jpg


REMOVAL
1. REMOVE V-BANK COVER SUB-ASSEMBLY
2. REMOVE NO. 1 ENGINE UNDER COVER

4cff58f.jpg



3. REMOVE FAN AND GENERATOR V BELT
(a) While turning the belt tensioner counterclockwise, align the service hole for the belt tensioner and the belt tensioner fixing position, and
then insert a bar of [diameter]5 mm (0.197 in.) into the service hole to fix the belt tensioner in place.
HINT: The pulley bolt for the belt tensioner has a left-hand thread.
(b) Remove the V belt.



1. INSTALL FAN AND GENERATOR V BELT
(a) Set the V belt onto every part.
(b) While turning the belt tensioner counterclockwise, remove the pin.
NOTICE: Make sure that the V belt is properly set to each pulley.
(c) After installing the belt, check that it fits properly in the ribbed grooves.
HINT: Make sure to check by hand that the belt has not slipped out of the grooves on the bottom of the pulley.
2. INSTALL NO. 1 ENGINE UNDER COVER
3. INSTALL V-BANK COVER SUB-ASSEMBLY

c0b77ac.jpg

Sep 28, 2009 | 2007 Toyota Tundra

1 Answer

Fan belt


THE diagram should be on the front of the car undre the hood by the hood latch

Feb 14, 2009 | Renault Sport Cars & Trucks

1 Answer

How to fit a renault scenic fan belt


Basically locate the tensioner which is a round black plastic pulley, it should have a 13mm bolt through the middle of which, and an allen key hole as well? This hole may also be in the form of a torx ?
There are so many difference types of engine it would be difficult to explain all of them.
On some tensioners you must put your 13mm (long) spanner onto the bolt and lever it toward yourself (from front of vehicle), this will allow slack on the belt, dont let go, have your assistant pull the belt off whilst you hold the tensioner off.
Then simply refit the belt / fit a new one. Dont forget the way it is routed, i.e draw picture of how the belt sits around each pulley.

Dec 14, 2008 | 2001 Renault Sportwagon

1 Answer

1998 renault scenic water pump replacement


to replace the pup the timing belt must be removed. water pump removed. new 1 saled and fitted and t belt replaced

Aug 21, 2008 | 2000 Renault 181

Not finding what you are looking for?
2007 Saturn Aura XR Sedan Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saturn Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22258 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8725 Answers

Are you a Saturn Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...