Question about 2007 Toyota Camry

Open Question

Toyota push button start no key detected - 2007 Toyota Camry

Posted by Anonymous on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 11800 Answers

SOURCE: My toyota highlander 2009 keep

I'm assuming that the truck was properly maintained and the battery and the alternator are in good working order: more than 12.3 volts on the battery with the engine off, more than 14.2 with it on.
You have a lot of apparently separated problems:
- the TRAC and VSC OFF lights are on because you have steering and transmission sensor problems - the data coming from them is corrupted and the ECM detects that as a fault and the warning lights are triggered. You will need to have the error coded read to find out what actually happened.
- the oil maintenance is a reminder that the oil must be replaced according to the manual - the miles you have done with it have reached the recommended value. Just replace the oil and the filter.
- the brake warning is triggered when the brake fluid is low in the bowl, the handbrake is on, or the pads are worn out - you will need to check them all.
- the antenna for the key transponder is located under the logo so putting the key near the receiver, which is in the button, has allowed the passage of the signal. Since the transponder is an RFID one - powered by the receiver remotely - it means that the receiver is faulty and you will have to replace it.
I find it highly unlikely that all those faults have occurred all at once on a single car. Have the entire wiring of the car inspected by a specialized repair shop, you have serious problems in there.

Posted on Sep 02, 2011

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I reset the oil indicator light on a 1996 Toyota paseo


1.With the car started (ignition on), set the LCD odometer readout to total mileage (not trip A or B).
2.Turn the car off (ignition key to the OFF position).
3.Push in AND HOLD the button/knob that switches the odometer
4.Turn key to ON position without starting the car. You will notice the maintenance light blink and go out.
5.Release the odometer button/knob.
6.Turn key to OFF position.

Jun 02, 2015 | Toyota Cars & Trucks

1 Answer

Venza remote keyless entry problems


I have the 2010 Toyota Venza push to start. I lost the original key, so i bought a new key with the remote and its was programmed successful but this remote only had the three buttons on it, instead of four buttons ( Including the Hutch button). So i bought another new remote with the four buttons today and I want to know if it will work when i switch the programmed key into the new remote?

Feb 04, 2012 | Toyota Venza Cars & Trucks

1 Answer

My 2008 prius won't start when the button is pushed. It only starts when the key is inserted.


Make sure you are stepping on the brake petal when you push the start button or it won't start up.

Oct 20, 2011 | 2008 Toyota Prius

1 Answer

I just purchased a 2008 Toyota Highlander with the smart key ignition system. How can I prevent being stranded if the smart system won't start the car?


If the smart key battery gets low to where it won't start the car you can hold the smart key with the logo facing the start button close to the button then push it to start the engine.

Aug 24, 2011 | 2008 Toyota Highlander

1 Answer

2008 Toyota 4Runner maintenance light is on eventhough I did changed the oil. How do I reset it?? I tried one of the suggestions which included turning the key to on and resetting the trip miles but...


You were close with re-setting the trip miles. Here are the steps:

(1) Turn key on, but do not start car. Keep pushing the trip miles button until you get to the odometer miles (the total mileage of the car), not the trip miles.

(2) Trun key off.

(3) Push and HOLD the reset button with one hand, then turn the key on (do not start the car) with the other.

(4) While you continue to HOLD in the reset button, you will notice the various warning lights blink and turn off. After about 10 seconds, release the reset button.

(5) Turn key off, then turn key back on and start car. The maintenance light will be off.

May 16, 2011 | 2008 Toyota 4Runner

1 Answer

We have a 1989 toyota camry the key will not turn to start the car. It has a button on top of the stering column to release the key when you turn the car off and normally when you put the key in you have...


Hi
Sounds like the ignition barrel has failed.
If you replace any part you must ensure that the key and the transducer ring are matched. If not, the immobiliser will come on and you will never start the car.
Get a diagnostic test to verify the immobiliser is turning off.
Roger

Apr 24, 2017 | 1989 Toyota Camry

1 Answer

Maintanance light on a 2007 Toyota Camry LE


Push and hold trip button on dash with key off, turn key on but don't start, odometer will clock down, when it is finished, lite will go off

Apr 01, 2009 | 2007 Toyota Camry

2 Answers

Maintenance lite stay on after oil change


If you have the owners manual it should be in there. I know each make has adifferent way to reset. Gm is key on key off and accelerator three times. I am not sure if that is exactly correct but hope it will help you to find your answer

Dec 15, 2008 | 2008 Toyota Highlander

1 Answer

Oil change light


Turn the key on. Observe the odometer. Is "ODO" displayed? If not, push the trip meter button until "ODO" is displayed, with the total mileage travelled shown.
Turn the key off.
Push & HOLD the trip reset button until advised to release it.
Turn the key to "ON" (do not start engine)
Observe the ODO display.
You should see 5 dashes, then 4, then 3, then 2, then one, and finally, five zeros.
The original mileage that you observed should be redisplayed.
Release the trip reset button.
The proceedure is now complete.

Jul 29, 2008 | 2004 Toyota Corolla

Not finding what you are looking for?
2007 Toyota Camry Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22258 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8725 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...