Question about 2005 Dodge Ram

Open Question

Tailgate removal 2013 dodge ram 3500 dually

Due to the torsion rod assembly, what steps are needed to remove tailgate

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: remove front axle from differential on 2003 dodge ram

That works fine on a relatively new vehicle but one that has run in salt etc you'll save a lot of time if you remove the steering knuckle completey by separating lower ball joint and outer tie rod end ball joint and bring the whole steering knuckle to a bench to separate the hub/bearing. Soak everything with penetrant, loosen the bolts a few turns and try hitting right on the bolt heads. I also made a very sharp wedge from a chisel and rammed it hard on the other side to seoarate the hub. It will finally come apart then you'll see all the **** that was binding it due to an alumininum knuckle re-acting with a steel hub. Clean the hole and grease everything and fit new bearings

Posted on Feb 15, 2009

Ad
ftw1952
  • 10319 Answers

SOURCE: To replace the rear fender on my 2005 Dually, how

they bolt on through the bed which is a hard one to change for most

Posted on Feb 05, 2010

  • 593 Answers

SOURCE: Remove headlight assembly from a 2001 Dodge Ram

On the upper grill side of the headlight assy. there
should be 1 or 2 push pins that hold the seal on the
headlight assy to the front of the fender. Also check
for a guide/push pin on the inner top of the assy on
the outer fender side. That should be all there is to
hold the headlight in place. Hope this helps.

Posted on Apr 10, 2010

  • 37 Answers

SOURCE: how to remove the rear brake rotor on a 2006 dodge

Single rear wheel - Remove both caliper bolts.. remove caliper and pads.. remove rotor.. they are usually rusted on pretty good.

Rear Dually- the rear rotors are mounted with the hub assembly.. you must first remove the rear axles.. then remove nut holding load on bearings.. then the rotor and hub assembly will come off as one unit.. removed rotor from hub..

Posted on Apr 13, 2010

  • 63 Answers

SOURCE: Hello, the rear axel seal on my Dodge Ram Dually

is not that bad just take the tires off then take the diff cover off take the drum or disc off on some truck there is four bolts on the end of the axle tube that you have to remove to get the axle out. but, if you look insider the diff and see two clips that look like a c ust take the bar that runs threw the middle of the diff and holds the spider gears inplace and keeps the axle from moving back and forth out and push the axles in and remove the clips then pull the axle out and rip the sear out and install the new one.

Posted on Jul 02, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove rear tail light lens Dodge 3500


See video...
If you open the tailgate, you will see 2 screws inside the frame for the tailgate (underneath the strikers on either side). remove these and you should be able to pull the assembly completely out with a little wiggling and force.

Jul 23, 2015 | 2010 Dodge Ram 3500

1 Answer

Need torque specs for front wheel bearing on 2004 dodge 3500 dually


The hub bearing retaining bolts are 150 ft. lbs the center axle nut primary torque 135 ft.lbs rotate 5-10 times increasing torque by 50 ft.lbs until final torque of 265 ft.lbs is reached

Mar 23, 2014 | 2004 Dodge Ram 3500 Truck

1 Answer

How do you change rear brake drum on 2002 dodge ram 3500 dually


you have to get under truck look for access hole at backing plate you need brake adjusting tool to turn adjusting star wheel until drum brakes away from brake drum so you can remove the brake drum.you need tools to remove rear wheel from drums you need a large breaker bar and large hammer and a large socket remove spindle nut.

May 18, 2013 | 2002 Dodge Ram 3500 Truck

1 Answer

How to remove rotor on rear of 2005 dodge 3500? Do I need special equipment?


If you truck has a standard rear axle just remove the caliper and caliper adapter bracket, then the rotor will pull off. Sometimes if the hub face is rusted it may take a little persuasion to come off. You can hit it with a ball peen hammer between the wheel studs, this is usually enough to free it. If you have a dually you will need to remove the axle shafts first by removing the bolts around the outside of the axle housing then pull the shafts outward. Then remove the caliper and caliper adapter. Slide rotor and hub assembly off of axle, then unbolt the the hub from the rotor.

Jan 20, 2011 | 2005 Dodge Ram 3500

1 Answer

What is the procedure for replacing ball joints in 2004 doddge ram 3500 4wd quad cab dually?


first put truck on jack stands and remove tires then you will need heavy duty impact to remove axle nuts then remove the four bolts that hold wheel bearing in you access them from the back side of rotor on the spindle then remove the brake caliper and bracket you will need a puller to put on the rotor or studs and push against the axle shaft dont forget to unplug speed sensor if equipped after you remove rotor and bearing assembly the axle will slide out allowing you to get to lower ball joint nut remove both nuts and steering rod use ball joint fork and remove spindle use press and remove and reinstall new joints put back in reverse order be very careful with left side axle make sure its clean and hold it up in the center as not to damage seal when going back in because it is bear to replace i hope this helps you allow yourself a good day for this job

Nov 03, 2010 | 2004 Dodge Ram 3500 Truck

2 Answers

How to remove the rear brake rotor on a 2006 dodge ram 3500 dually


Single rear wheel - Remove both caliper bolts.. remove caliper and pads.. remove rotor.. they are usually rusted on pretty good.

Rear Dually- the rear rotors are mounted with the hub assembly.. you must first remove the rear axles.. then remove nut holding load on bearings.. then the rotor and hub assembly will come off as one unit.. removed rotor from hub..

Mar 23, 2010 | 2006 Dodge Ram 3500 Truck

1 Answer

Need to replace the driver side taillight


if you lower the tailgate those are the screws i think your talking about,yes remove them and swing the lense out pulling from the side the screws were on,it will unhinge its self on the outer side

Dec 10, 2009 | 1998 Dodge Ram 3500 2WD

1 Answer

How to remove a tailgate of a 2005 dodge ram


· Open the tailgate and remove the tailgate liner.
· Remove the ten bolts(5) that secure the tailgate cover(4) to the inside of the tailgate and remove the cover.
· Using a pencil,mark the actuator rod(3) at the control(2) for the latch(1) being serviced.
· Disconnect the actuator rod from the control
· Remove the two bolts(7 and 8) that secure the latch(5) to the tailgate(4) and position the tailgate check cable(6) out of the way.
· Remove the latch and actuator rod from the tailgate as an assembly.
· If required,remove the actuator rod from the latch.
You will have to remove the tailgate cover. The cover will most likely be held on by some of the tailgate metal access cover.

Oct 06, 2009 | 2005 Dodge Ram

1 Answer

I need a diagram on front hub and brake assembly for 1999 dodge 1 ton dually 2 wheel drive. the front brake rotor is warped i need to replace it


8–Stud Rotor
  1. Raise and support the vehicle.
  2. Remove the wheel.
  3. Remove the hub extension.
  4. Remove the brake caliper assembly.
  5. Remove the axle nut cotter pin. Remove the axle nut.
  6. Disconnect the ABS wheel speed sensor wire from under the hood. Remove the sensor wire from the frame and steering knuckle, if equipped.
  7. Back off the hub/bearing mounting bolts 1/4 inch each. Then tap the bolts with a hammer to loosen the hub/bearing mounting bolts.
  8. Remove the bolts and remove the hub/bearing assembly.

Sep 16, 2009 | 2000 Dodge Ram 3500

1 Answer

Serious understeer with 96 Dodge Ram 3500 Dually


Are the tie rod ends tight? Is the trac bar (frame end) tight? The steering boxes on these trucks require more input that a 1/2 ton truck or a car. How is the alignment? The caster on these should be set to about 5 degrees, the original specs allow a lot of wandering.

Apr 05, 2009 | 1996 Dodge Ram 3500 Club Cab

Not finding what you are looking for?
2005 Dodge Ram Logo

Related Topics:

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...