Question about Mercedes-Benz E320

Open Question

HEAD TORQUE 1997 MERCEDES 320

COULD YOU GIVE ME THE TORQUE SPECS FOR THE HEAD

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
chuck943
  • 783 Answers

SOURCE: Head bolt torque specs needed for 96 tbird 3.8

Head bolts are torque to yeild so you MUST use new bolts.
Tighten cylinder head retaining bolts in numerical sequence in three steps as follows:

  1. 20 Nm (15 lb-ft).
  1. 40 Nm (30 lb-ft).
  1. 50 Nm (37 lb-ft)
Loosen retaining bolts one at a time two to three revolutions and retighten as follows:

Long bolts:
  • Tighten to 40-50 Nm (30-37 lb-ft).
  • Rotate an additional 175-185 degrees.
  • Go to next bolt in sequence.
Short Bolts:
  • Tighten to 20-30 Nm (15-22 lb-ft).
  • Rotate an additional 175-185 degrees.
  • Go to next bolt in sequence.
Here is a pic of the sequence
http://i253.photobucket.com/albums/hh43/chuck943/Headboltsequence38L.gif

Posted on Mar 19, 2009

Ad
inspectmycar
  • 233 Answers

SOURCE: 94 mazda B3000 3.0L cylinder head torque specs

Step 1 torque to 59 ft pounds
2. Loosen one full turn
3. 37 ft pounds
4. 68 ft pounds

Use torque sequence below
aca9f77.gif

Posted on Sep 17, 2009

BCAS1298
  • 3092 Answers

SOURCE: Head bolt torque specs on 1997 ford escort 2.0

STEP # 1 30 - 44 FT.LBS
STEP # 2 ADDITIONAL 90deg
STEP # 3 ADDITIONAL 90deg

AFTER STEP # 1 LOOSEN BOLTS 1/2 TURN, THEN DO ALL 3 STEPS.

MAKE SURE YOU TIGHTEN IN SEQUENCE.

Posted on Nov 06, 2009

GMJunkie
  • 74 Answers

SOURCE: Need Cylinder head bolt torque specs and sequence

  1. Install the cylinder head gasket. Ensure the arrows point towards the front of the engine. The left cylinder head gasket has the letter L stamped next to the arrow.
  2. Notice
  3. This bolt is designed to permanently stretch when tightened. The correct part number fastener must be used to replace this type of fastener. Do not use a bolt that is stronger in this application. If the correct bolt is not used, the parts will not be tightened correctly. The system or the components may be damaged.

  4. Install the cylinder head.
  5. Install new cylinder head bolts. Tighten
    Tighten the cylinder head bolts to 50 N·m (37 lb ft) in sequence.
  6. Use the J 36660-A to rotate each cylinder head bolt 120 degrees in sequence. Use the J 36660-A to rotate the four center cylinder head bolts an additional 30 degrees in sequence. Refer to Notice Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

d429947.gif

Posted on Mar 10, 2010

wilsodfarm
  • 986 Answers

SOURCE: Torque Specs for Head Bolts on 1997 GMC Sierra V8 5.0 Vortec?

.0L Torque Specs Belhousing to engine bolts 28-38 ft/lbs Camshaft sprocket bolt 40-45 ft/lbs Camshaft thrust plate to engine block bolts 108-144 in/lbs Crankshaft pulley to vibration damper bolts 35-50 ft/lbs Cylinder head bolts -1979-1992 --Step 1 55-65 ft/lbs --Step 2 65-72 ft/lbs -1993-up --Step 1 25-35 ft/lbs --Step 2 45-55 ft/lbs --Step 3 75-85 ft/lbs Differential shaft lock bolt 15-30 ft/lbs Driveshaft U-joint to pinion flange bolts 70-95 ft/lbs Exhaust manifold bolts 26-32 ft/lbs Flywheel mounting bolts 75-85 ft/lbs Front engine mount nuts 72-98 ft/lbs Intake manifold to head bolts --Step 1 96 in/lbs --Step 2 16ft/lbs --Step 3 23-25 ft/lbs Intake manifold (upper intake to lower) 12-18 ft/lbs Oil filter insert to engine block adapter bolt 20-30 ft/lbs Oil pan mounting bolts -1979 --Step 1 (Large bolts) 11-13 ft/lbs --Step 1 (Short bolts) 7-9 ft/lbs --Step 2 (Large Bolts) 15-17 ft/lbs --Step 2 (Short Bolts) 10-12 ft/lbs -1980 to 1987 9-11 ft/lbs -1988 to 1993 6-9 ft/lbs -1994-up 110-144 in/lbs Oil pickup tube to main bearing cap nut 22-32 ft/lbs Oil pickup tube to oil pump bolts -1979 to 1987 10-15 ft/lbs -1988-up 12-18 ft/lbs Oil pump mounting bolts 22-32 ft/lbs Pinion bearing preload 8-14 in/lbs Pressure plate to flywheel bolts 12-24 ft/lbs Rocker arm fulcrm bolts 18-25 ft/lbs Spark plugs 7-14 ft/lbs Timing chain cover bolts 12-18 ft/lbs Vibration damper to crackshaft bolt 110-130 ft/lbs Wheel lug nuts 85-105 ft/lbs

Posted on Mar 16, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Engine head gasket


I suggest you purchase a repair manual for your Benz, if available. It's a major task to remove the head(s) and replace the gasket. You'll need torque sequencing specs, probably new head bolts, etc. You should have the head checked at a machine shop for warping. I think it's beyond the scope of this web site to give very detailed and explicit instructions for such a major engine job. Good luck....

Apr 27, 2014 | 1980 Mercedes-Benz 280 SLC

2 Answers

1997 cavalier head gasket replacement with a 2.2. Also need the torque specs and sequence for the head bolts


Go onto Autozone.com and sign up for their online repair. It is free to use but you have to register.

Nov 16, 2010 | 1997 Chevrolet Cavalier

2 Answers

Torque specs for lifters 1997 2.2 chevy cavalier


You should buy a manual. If someone gave you an incorrect number you could have serious problems.

Apr 26, 2010 | 1997 Chevrolet Cavalier

1 Answer

Need head bolt torques, replacing head gasket in a Merc ML350


call a parts store they have them and will give them to you or call manufacturer itself .youll get your torque specs

Jun 17, 2009 | 2007 Mercedes-Benz ML350

1 Answer

I have a 1997 hyundai elantra 1.8 i need torque specs. for head


go to http://www.hmaservice.com/ and register. After that, you'll have access to manuals, service bulletins, wiring diagrams, etc.

May 17, 2009 | 1997 Hyundai Elantra

1 Answer

I need torque specs for head bolts on 1992 merc benz 230 e


hello,230e with engine 102.982,cylinder head bolt,double hexagonal socket m12, stage 1, 55 newton meter,stage 2 90 degrees stage 3 90 degrees,4 pcs. bolt with m8 tighten to 25 nm.ref. technical data year 1993,ty

Apr 17, 2009 | 1992 Mercedes-Benz E-Class

1 Answer

Head bolt torque specs for 1992 Pontiac 3.1 ltr


the last time i did the same job the gasket kit had the specs inside the box. the parts store should have a book/reference manual

Dec 09, 2008 | 1992 Pontiac Grand Prix

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76164 Answers

Michael Contreras
Michael Contreras

Level 2 Expert

166 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...