Question about 1998 Toyota Tacoma

Open Question

Remove door panel

Replace exteror door handle

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: broken outside door handles (front

I have the same problem on a Toyota Tercel 1997. I am trying to remove the door panel with the door closed (I can not open the door because the door knob is stuck in the lock position). I think I will have to cut through the panel. Have you found something ? My e-mail is philippe_oreilly@yahoo.ca

Posted on Aug 23, 2008

Ad
  • 1861 Answers

SOURCE: Replace side door handle assembly

Remove the snap ring from under the inside door handle and plate (a rag around the base of the handle and a left-right tug on the rag may loosen it, or look under it & pry the snap ring off with a small hook tool

Remove the door lock knob bezel; remove the screw & slide it rearward

Remove the door trim; Remove the two clips; slide a thin, flat wide tool under the panel and pry towards you, there are 8 clips to dislodge

Pull the door trim straight up once all of the clips are loosened.

Easy.

Posted on Sep 25, 2008

  • 840 Answers

SOURCE: Broken handle on sliding door behind driver

First get vin call toyota parts dept/ get the part its really easy to put in look for screws in little pop ups take screws out then go from the bottom of the door and lift out then go side do the same thing then lift from bottom of door and upward then you will take of vapor or plastic sheet then you just replace the handle thats it then out it back together/ Please rate my response thank you very much

Posted on Feb 01, 2009

  • 2 Answers

SOURCE: To remove the interior door panel of a 1996 Toyota camry so that

My 96 Camry LE has 9 attachments that are visible. Some have plastic caps covering the screws; others do not. There are screws at the door handle, at the forward portion(with covers) when the door is open and the back edge (small covers). As I recall, there are several friction type fasteners around the perimiter of the panel that can be removed by prying carefully away from the metal portion of the door to free up the trim panel. Once these are loose, the trim around the inside door release handle (the one you pull to open the door) can be pryed in a backward motion. Then the entire panel can be removed by pulling upward and backward at the same time (it easier to do this with the window down). Then it is a matter of disconnecting the wires attached to the various controls for the electric windows and door locks to free up the panel itself. There is probably a plastic skin covering the metal portion of the door. Carefully pull that away to expose the inner workings of the door latch mechanisim. The rest of the procedure should become easy to figure out. I have not removed the exterior door handle itself; but it is a simple mechanism as I recall. Best of luck to you.
Timmy P.

Posted on Mar 04, 2009

  • 259 Answers

SOURCE: remove door panel on drivers side 1998 sienna

there should be two screws holding it to the door panel could be concealed under a cover hope this helps regards Jim

Posted on Apr 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Remove interior door panel 2002 Chevy tracker


No you don't need any special tool . Find all screws on out side of door trim panel and the window handle , the mirror cover plate , then just pull on edge of the panel .
Gently pry the front side door trim panel (3) from the front side door by disengaging the plastic retainers which secure the panel.
Position the door trim panel (3) away from the door in order to gain access to the front side window switch electrical connector, if equipped.
Disconnect the window switch electrical connector, if equipped.
Remove the door trim panel (3) from the vehicle.
Remove the front side window switch from the door trim panel (3) by releasing the 4 plastic retaining tabs, as needed.

Use a cloth in order to pull off the snap ring which secures the front side door window regulator handle (1), if equipped.
Remove the window regulator handle (1), if equipped.
Remove the front side master window switch, if equipped. Refer to Power Accessory Switch Panel Replacement .

Remove the front side door inside handle (1). Refer to Front Side Door Inside Handle Replacement .
Remove the outside rearview mirror opening cover (2).
Remove the screw which secures the front side door pull handle (4).

Front Side Door Inside Handle Replacement
Removal Procedure
Remove the screw which secures the front side door inside handle (1).
Slide the inside handle (1) forward in order to release the retaining tabs which secure the handle to the door.
Open the front side door inside handle rod retainer and remove the front side door inside handle rod from the inside handle (1).
Remove the inside handle (1) from the vehicle.

Check out youtube video showing how to do it !
How To Remove Install Front Door Panel Suzuki XL 7

Jun 10, 2017 | Cars & Trucks

1 Answer

Need a guide on how to handle of the door


  1. How it's done:
    1. Remove the door panel to gain access.
    2. Remove and replace the broken door handle.
    3. Inspect door latch and replace if not working.
    4. Check door for proper operation.
    5. Reinstall door panel.

Door Handle or Door Latch Replacement Service Cost YourMechanic

Mar 20, 2015 | Cars & Trucks

1 Answer

How do I replace and fit an extrior RH door handle to a 1995 Suzuki Baleno?


Open the door and remove the door panel with a special tool. Take out the screws on the door panel and any knobs or latches. Remove the panel. Cut the dust or noise seal, it is a messy liner that looks like paper or plastic. Remove the window hardware if you cannot get to the door handle screws from the openings in the door. Remove the window if you do this. Then you can replace the handle. Be mindful of the sharp edges that are present on the door.

Sep 12, 2014 | Cars & Trucks

1 Answer

Need to put passenger miror on. i need help to show me how to take the door panel off.


Section 01-05: Trim, Interior 1998 Windstar Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 01/22/1999 Trim Panel, Door Front
Removal
  1. Remove door latch cover by prying from top edge and pulling trim free of retaining clips and sliding trim away from latch.
  1. Remove portion of armrest containing door lock switch and window regulator control switch (14529) by pulling straight up.
  1. Remove rear view outside mirror mounting hole cover assembly by prying at top and pulling upward to release double-sided clip.


    Trim Panel


    ar0885a.gif


    Item Part Number Description 1 23942 Front Door Trim Panel 2 56908-S58 Screw (1 Req'd), Right Door 56906-S58 Screw (1 Req'd), Left Door 3 18B978 Radio Speaker Grille Name Plate 4 56911-S58 Screw (1 Req'd) 5 17D720 Cover Assembly Rear View Outside Mirror Mounting Hole
  1. Remove screw attaching front door trim panel (23942) to front door (20124) under switch plate.
  1. Remove two screws located at bottom of front door trim panel.
  1. Disconnect the door lock switch (14028) and window regulator control switch electrical connectors.
  1. Remove door window regulator handle if equipped by unsnapping and pivoting away the handle cover from base to expose retaining screw. Remove screw from the door window regulator handle.
  1. Pull front door trim panel from the top to release hooks from front door .
  1. Remove front door trim panel.
Installation
  1. Replace any bent or damaged fasteners.
  1. Follow removal procedure in reverse order.
Body Side
Removal
  1. Remove door handle retaining clip by sliding a shop towel between handle and door trim. With tension on the cloth, pull one end of the cloth so it slides between the handle and the door trim. If handle does not come out, reverse direction.
  1. Unfasten 13 christmas tree fasteners using double-acting spring-loaded trim removal tool and pull body side trim panel from body side door.
  1. Remove forward and rearward mating sections from under window trim.
Installation
  1. Replace all christmas tree fasteners.
  1. Follow removal procedure in reverse order.
  1. For installation of handle, install clip to handle, then push handle onto shaft to snap in place.


    r11176a.gif

Back
Removal
  1. Disconnect rear window defroster wires.
  1. Remove the liftgate window garnish moulding as described.
  1. Remove screws attaching liftgate handle to liftgate and liftgate inside trim panel.
  1. Using Rotunda Windshield and Moulding Trim Removal Kit 107-R0401 or equivalent, pry pushpins retaining liftgate trim from the liftgate.
  1. Remove liftgate trim.
Installation
  1. Follow removal procedure in reverse order.


    Liftgate


    r10441a.gif

2010&c18=modelyear&c35=wsm%2ctrim%20panel%2c%20door%2csww%2c01-05%2cremoval%20and%20installation&s=1366x768&c=32&j=1.3&v=y&k=y&bw=995&bh=405&ct=lan&hp=n&[aqe]

Mar 07, 2011 | 1998 Ford Windstar

1 Answer

Replacing driver side door handle


First, ya gotta remove the interior door panel....

Door Panel
  1. Fully lower the door glass.
  2. Remove the arm rest, door lock knob and inside door handle escutcheon.
  3. Remove the regulator handle.
  4. Gently pry the door panel away from the door.
  5. Installation is the reverse of removal. Install the regulator handle (correct position) with the door glass closed.
Next you'll need a small ratchet and extenstion with socket...or a socket driver (like a screwdriver but holds a socket). Remove the two nuts attaching the handle to the door. Use a long thin flat screwdriver and pop loose the clip attaching the rod to the lock mechanism..
Manuever the handle off the door and then install in reverse order.

May 28, 2010 | 1987 Nissan Pickup

1 Answer

Replace outside door handle


you need to remove the inside door panel first. there will be a screw at the inside door handle and two screws for the armrest in the center of the panel. look around the outside edges of the panel for any other screws or clips to remove. the rest of the clips are behind the panel and snap when you pull on the panel. once off with the window up you can see the door handle screws. two of them. remove the connecting rods first.depending on which door you may have a lock rod also. then remove the screws and the handle will come out. good luck

May 22, 2010 | 1998 Toyota Corolla

1 Answer

I have a susuki forenza and I need to replace the driver's side door handle. I already have the new part (door handle).


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can remove the inner door handle and replace with new one. If it's your outer door handle, pull back the weather seal and disconnect the linkage to the outer door handle and then remove the bolts securing the outer handle to the door

Oct 23, 2009 | 2006 Suzuki Forenza

1 Answer

Inner door panel door removal


Coupe
  1. Disconnect the negative battery cable.
  2. Remove the screw covers, screws and pushpin, then remove the door pull handle applique.
  3. If equipped, unplug the regulator switch plate electrical connector.
  4. Mark the position of the window regulator handle, then remove the handle using a suitable tool to disengage the regulator handle snapring.
  5. Remove the pushpins from the trim panel.
  6. Slide a flat-bladed tool behind each of the retaining clips and twist to disengage the clips from the door shell.
  7. Remove the trim panel by lifting it up and sliding it rearward to clear the sheet metal.
e8dcd1b.gif
Remove the door pull handle applique

b24cb71.gif
If equipped, unplug the regulator switch plate electrical connector

90d8d42.gif
Remove the two-piece pushpins from the trim panel

To install:
  1. Replace all damaged trim panel retainers.
  2. If removed, install the water shield.
  3. Place the trim panel into position on the door and insert the door handle through the opening.
  4. Attach the door panel fasteners.
  5. Install the pushpins on the trim panel.
  6. Install the regulator handle.
  7. If equipped, attach the regulator switch plate electrical connector.
  8. Install the door pull handle applique cover, the screws, screw covers and the pushpin.
  9. Connect the negative battery cable.

Oct 11, 2009 | 1998 Ford Escort

1 Answer

How to replace inside door handle on passenger on 1998 chevy silv


Remove screw from inside door grab handle. Remove door panel by carefully prying out plastic clips. Drill or chisel off pop rivets holding the handle on. Pull handle out far enough to disconnect linkage and remove handle. Install new handle and secure to metal panel with new pop rivets or sheet metal screws. It may be easier to reconnect linkages by removing the metal panel also.

Apr 11, 2009 | 1998 Chevrolet K1500

1 Answer

Remove right rear door panel


  1. Remove the rear door power window/power door lock switch
  2. Remove the door handle bezel. Remove the door trim panel screw located behind the door handle bezel.
  3. Remove the door trim panel screws located by the armrest handle.
  4. Remove the door trim panel using J 38778.
  5. Disconnect the electrical connectors.
  6. Remove the door trim panel from the door.
INSTALLATION PROCEDURE

IMPORTANT: Discard the old door trim panel retainers and replace with new retainers before installing the trim panel

  1. Install new trim panel retainers to the rear door trim panel.
  2. Connect the electrical connectors.
  3. Align the door trim panel retainers to the door.
  4. Press the door trim panel at the retainer locations until the retainers are fully seated.
  5. Install the trim panel screws. Tighten Tighten the door trim panel screws to 2 N.m(18 lb in) .
  6. Install the power window/power door lock switch


Nov 04, 2008 | 1998 Oldsmobile Intrigue

Not finding what you are looking for?
1998 Toyota Tacoma Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22258 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8725 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...