Question about Toyota Dyna

Open Question

How to set valve clearance on the Dyna 15B - Dyna Toyota Cars & Trucks

Posted by Anonymous on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 45659 Answers

SOURCE: How do I set the valve clearances on a kia 2700

hydraulic followers should not need adjustment as it is automatically done by the oil pressure in the followers.

Posted on Dec 20, 2014

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

On a Toyota dyna 14b cylinder head,what sizes are inlet and outlet valves take?


hi this is a 2kd-ftv engine the clearance will be for exhaust 0.35mm, 0.45mm cold, for inlet it is 0.20mm , 0.30mm cold

Dec 18, 2016 | Toyota Cars & Trucks

1 Answer

What is the valve clearance for intake valve and exhaust valve for mitsubishi engine 4D32?


Please follow link to complete instuction's on the Correct way to set valve clearance on the 4D32 engine type.
6 INTAKE AND EXHAUST VALVE CLEARANCE INSPECT AND ADJUST

May 15, 2016 | Mitsubishi Cars & Trucks

1 Answer

Valve setting


Personally, the valve clearance (if nobody's been messing with it) would be last on my list of suspected causes.. Knowing diesel engines like I do, my very first suspect would be a dirty fuel filter.

Dec 03, 2013 | Cars & Trucks

2 Answers

Please assist with Cylinder Head Torque and Valve Clearance Specs for Tata Indica 1.4 LXi


i need the head talk settings & valve clearance for tata indica lxi

Apr 20, 2013 | 2006 Tata Indica LXi

1 Answer

Torque settingsfor head on lister petter mini6 engine


I have just rebuilt one for our Westerly 21. This is from my Petter 'A' range workshop manual:-
The water cooled engines (AC1W etc.) are:cylinder head nuts: 30NM (22 lbft) except 32.5NM (24 lbft) for the one that also holds the rocker.
Valve clearances are 0.1mm (0.004") COLDReset valve clearance after one hours running since torquing the head.
Retorque head and set valve clearance after initial 20 hours running
I believe Mini-6 refers to the water cooled engines but just in case, the air cooled engines are 27N (20 lbft)

Mar 27, 2012 | Cars & Trucks

1 Answer

Valve clearence settings mazda protege 2003


This is for a non turbo2_24_2012_5_45_49_am.gifNew adjustment shim =Removed shim thickness+ measured valve clearance- STANDARD VALVE CLEARANCE (0.26 mm or 0.010 inch)

Feb 24, 2012 | Mazda Protege Cars & Trucks

2 Answers

I have problem with my engine 4K toyota. It heard an engine noise during idling, for my little knowledge in engine repair, can you give me any procedure mannuals in adjusting engine valves for my...


Valve Clearance Valve clearance is there to allow the valves to cool in between combustion events (spark), and to make sure the valve closes properly and contains the combustion explosion. You need to cool the valves a little bit, the exhaust valve moreso than the inlet, as it's what sees the most heat as spent burnt gases go past it into the exhaust port. Run too little clearance and you'll cause the valve to "weld" a little bit to its' seat every time it closes, and then take seat metal off again when it opens. Do this enough times and you burn out the valve seat and need the head reconditioned. However, by running less clearance, the valve stays open for that little but longer, and you get more air in and out of the motor, and make more power. Run too much clearance and your motor just sounds like a diesel and loses power and tappet rattle annoys you while you're driving, so it's better to err on the side of caution.
The stock valve clearance (0.008" inlet / 0.012" exhaust, warm) is pretty good for any of the cams I've listed above, they're well-sized street cams, not really wild top heavy race cams that require super high compression to work, so don't be afraid to close the valves up a bit from the suggestions of the cam grinder, which will usually say between 0.010" and 0.014". There are a few ways to set your valve clearances:
Yellow Book Method This is from the factory 3K/4K/5K engine manual, aka The Yellow Books. It's the quick and lazy method.
Set engine to #1 TDC. Crank pulley timing mark should be on 0, distributor rotor should be pointing towards spark plug 1 or 2. Set tappets (counting from the front) 1, 2, 3 and 5. Rotate engine 360 degrees, crank pulley to 0 again, distributor rotor turned 180 degrees. Set tappets 4, 6, 7 and 8.
Nine Method I've never really gotten into doing this, takes too much time and maths for my liking :P Rotate the engine through its' range of movement, as one valve is "on the rock" of its' max lift, subtract the valve number from 9 and that's the tappet you should be setting. For example, if #8 valve is open, set clearance on valve #1. If valve #7 is open, set clearance on #2. And so on.
Stewart uses this method, and rotates the camshaft through its entire base circle and sets the clearance at the highest point. Which is a pretty good idea, as it compensates for the possibility that the base circle has been ground unevenly, and allows you to run the proper valve clearance that you want to run, instead of something that may be a few thou larger in reality.

Feb 10, 2011 | Toyota Corolla Cars & Trucks

1 Answer

What is the difference between hot and cold vavle clearances


When it is stated that valve clearance should be set when hot, you first adjust the clearance on the cold engine after assembly to the hot setting specs if they are the only ones given, then let the vehicle warm up to operating temperature. Then adjust the clearances again.
If it is just a tune-up(undisturbed engine), let the engine warm up to operating temperature, then adjust.
The reason is that metal expands as it heats up, which affects the valve clearance.

Dec 05, 2010 | Toyota Land Cruiser Cars & Trucks

2 Answers

Valve clearances for a ford econovan 1.8lt, 1990


what are the valve clearance specs for a 1990 ford econovan maxi

Mar 14, 2010 | 1989 Ford Econoline

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

97 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8589 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...