Question about 1997 Ford Expedition

1 Answer

How is the window glued in on the doors

I tried to roll the window and it was froze and need to know how to and what to use to glue it back in the track

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 131 Answers

Ford sales this special glue at the dealerships. You can also go to your local hardware store and purchase a 2 part epoxy that will work.

Posted on Feb 14, 2014


4 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 783 Answers

SOURCE: My power window came off track

There are 2 screws just above the door handle you need to remove. Remove the plastic trim around door handle. Then starting at bottom of door panel pull out to disengage the push pin clips and work your way up both sides of panel. Then lift up on door panel to disengage the weatherstip on top of panel.

Posted on Feb 10, 2009

  • 1986 Answers

SOURCE: how to put a window back on its track in a 02 mustang

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Pull off the weather seal and you can readjust the window from there

Posted on Oct 13, 2009

  • 85 Answers

SOURCE: the passenger window on my f 150 came unglued

3M Panel bonding adhesive is the proper adhesive. It is about $40. I would recommend thorough cleaning of the window using a razor blade and denatured alcohol. Also, remove the black seat clips and clean this area really well. Leave the window up for 24 hours in a heated garage to let the adhesive cure properly.

best of luck!

Posted on Jan 11, 2011

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Window off the track

The glass is held to the window track using glue which is available from your local dealer or you can purchase 2 part epoxy from Lowe's, that will work fine.

Feb 13, 2014 | 1999 Ford Expedition

1 Answer

Glue windows

the glass in the door window is not normally glued in the regulator track but is pressed in the rubber with the use of soap which dries out and that means that the pressure of the metal is what holds the glass in place. There will be difficulties if the window guides are incorrectly adjusted and the glass is allowed to go up an angle instead of straight up.. Normally the track at the back of the door is fixed and the front track is adjustable to hold the glass correctly

Oct 11, 2013 | BMW Cars & Trucks

1 Answer

My 2002 nissan altima door handle snapped off in the cold. What is the best option to replace it. Can it be glued back on or does it need to be fully replaces?

Glue will not be able to hold on a door handle. Too much pressure is required to open the door and the handle will only break off again if you try to glue it back on. Replace the entire handle assembly.

Jan 09, 2011 | 2002 Nissan Altima

1 Answer

Need to reglue rearview mirrow to front window. Got glue made for that purpose. Need to try and remove "silver button" from the back of the mirror so I can glue the button to the window then attach the...

The "silver button " is held in place with an anchor screw which you will need to look for and chose the right screwdriver to loosen it,then it should just slide out with your thumb.Gluing the mirror on is a one chance try so make sure it is in the right place the first time and hold the silver thing there with tape over night.The next day you can just slide the mirror on and tighten the set screw,then you are good to go!

Jul 15, 2010 | 1998 GMC Jimmy

1 Answer

2002 Jeep liberty back glass. The interior rubber

You might consider thoroughly cleaning the area on both the glass and the piece you are trying to adhere to it, then getting "Rearview Mirror Adhesive", available in your local auto parts store for >$10.

Follow the directions on the product precisely, and the handle should stay on there for you.

Dec 26, 2009 | 2002 Jeep Liberty

1 Answer

1996 BMW 318i passenger electric window wont roll up

problem with the window actuator assembly , will need to strip out to see the exact problem

Jun 07, 2017 | 1996 BMW 318

2 Answers

Window module and going up too high

I had the same problem. The window goes up to high because a L shaped bracket has come off the window.This bracket basically restricts the height of the window. Take the door panel off retrive the bracket that is roaming free inside your door and glue back on.There are 2 brackets both glued to the sits on the outside of the window the other ontop of that but inside.Use a strong glue otherwise it will keep happening. To anwer the first point the window is not supposed to go down.

Nov 29, 2008 | 1999 Mercedes-Benz SLK

1 Answer

Reapplying an undamaged weather strip/base of pass. window

At your parts store you can purchase a product called adhesive glue. In the business we call in yellow death. It is made by 3 M company.

Make sure both surfaces are dry, then apply the glue carefully to both surfaces to be glued.
Now, this is important. Bring both surfaces together for a minute, then carefully pull them apart a little distance. You will notice the glue becoming very stringy. Do this several times, as each time the glue will become tackier. The motion allows air to get to the glue, setting it up.
About the 3 or 4 time you will notice it becomes very sticky. That’s when you press the two surfaces together and press firmly against the door. It will be glued. That’s why we call it yellow death.

Be sure that it is the 3M product because there are imitations.

If you would like to contact me again about this or other problems, feel free to do so.
ASE Master Technician

Nov 26, 2008 | 1998 Mercury Mystique

1 Answer

Need to replace drivers lock/unlock switch

prob fixed...typed in add bar "how do you remove door panel on '98 mark 8" came up with exact directions. No charge...thanks anyway.

Nov 16, 2008 | 1998 Lincoln Mark VIII

2 Answers

2000 Hyundai Elantra driver's power window will not raise

don't know why but the glue gets weak where the plastic pieces attach to the bottom of the window.i've had to fix mine more than once.remove the door panel,then take the nuts lose from the back of the plastic retainers,then-going by the residue left from the old glue mark where the retainers go back-re glue,realine and reinstall.panel removal-philips screw holding the door handle,1 philips screw holding armrest/window controls,two philips screws at front of panel above speaker,then gently pry clips behind the edges of the panel.if the plastic window retainers are beyond repair,i think they have them in the help section of advance/autozone.

Sep 20, 2008 | 2000 Hyundai Elantra

Not finding what you are looking for?
1997 Ford Expedition Logo

76 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers


Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides