Question about Cars & Trucks

1 Answer

How to replace the side marker/position light bulb on the driver side? I can't even get to it because i can't get the light housing off!

2006 Volvo s60 side marker/position light bulb

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 2,044 Answers

The Headlight Assembly is not difficult to remove but you do need to be careful NOT to pull on the Headlight Assembly and break the clips

1. Open the S60's hood and locate the pin that is behind the headlight assembly of the bulb that needs replacement. The pin has a handle on the top. Pull the pin straight out of the headlight assembly.


  • 2. Push on the back of the headlight assembly until it comes out the front of the S60. There is an electrical connection on the back of the assembly; unplug the connection.

  • 3. Press on both clamp on the assembly. The clamps are on either side. Push them in together so that the cover releases.

  • 4 Uncover the bulb by pulling on the small plastic cover that covers each bulb. Push the visible wire aside. Pull the bulb straight out.

  • 5 Push a new bulb in and push the metal wire back over it to secure the bulb in the assembly. Push the covers back on.

  • 6. Reconnect the electrical harness to the assembly and push the assembly back into place. Push the retaining pin all the way back down into place.
  • Posted on Feb 13, 2014

    Ad

    4 Suggested Answers

    6ya6ya
    • 2 Answers

    SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

    Hi,
    a 6ya expert can help you resolve that issue over the phone in a minute or two.
    Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
    New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
    click here to download the app (for users in the US for now) and get all the help you need.
    Goodluck!

    Posted on Jan 02, 2017

    Ad
    • 1 Answer

    SOURCE: Position Light on Volvo S60

    Not sure but maybe you should verify rear position lights located in the trunk.
    There are two bulbs on each side, even if you replaced one of them the other one could be burned.

    Jean

    Posted on Mar 18, 2009

    morse008
    • 1111 Answers

    SOURCE: how to take off or replace driver side marker

    you can access it from under the hood or from under the vehicle and with a simple twist remove and replace the bulb

    Posted on Sep 10, 2009

    • 14036 Answers

    SOURCE: front side marker bulb replacement

    CHECK FRONT SIDE MARKER LIGHT COVER SHOULD HAVE SCREWS TO REMOVE LIGHT COVER SCREWS THEN YOU CAN REPLACE BULB.

    Posted on Aug 07, 2011

    Add Your Answer

    Uploading: 0%

    my-video-file.mp4

    Complete. Click "Add" to insert your video. Add

    ×

    Loading...
    Loading...

    Related Questions:

    1 Answer

    Replace marker light


    Removal Procedure
    1. Open the hood.
    2. Remove the headlamp. Refer to Headlamp Bulb Replacement .
    3. Rotate the bulb and socket counterclockwise in order to remove the bulb and socket from the housing. Remove the side marker bulb (3) or turn signal/park bulb (4) from the socket.

    Oct 01, 2015 | 2005 GMC Envoy

    1 Answer

    Marker lights wont go on


    on 1998 and earlier models, the side marker light housing is located next to the headlight housing. Remove the screws and pull out the housing to access the bulbholder on the back of the housing. On 1999 and later models, the park and turn signal bulbs are located in the bottom of headlight housing. Twist the bulbholders out to replace the park or turn signal bulbs. Installation is the reverse of the removal directions.

    Apr 04, 2013 | 1995 Jeep Grand Cherokee

    1 Answer

    Front side marker bulb replacement on 2006 liberty


    CHECK FRONT SIDE MARKER LIGHT COVER SHOULD HAVE SCREWS TO REMOVE LIGHT COVER SCREWS THEN YOU CAN REPLACE BULB.

    Aug 07, 2011 | 2006 Jeep Liberty

    1 Answer

    How do I change the front side marker light bulbs?


    Bi-Xenons - 6000K D1S
    High Beams - Osram Nightbreakers H7
    Fogs - PIAA H11 Yellow Ion
    Cornering Lights - Osram Nightbreakers H3
    Front Park Lights - High-Powered LEDs with built-in resistors
    Front Signal Lights - Sylvania Silverstar 7507A ST (Silver Bluish but lights up Amber)
    Front Sidemarkers - InviSilver W5W (Silver but lights up Amber)
    Rear Signal Lights - P21W Stealth Bulbs (Silver but lights up Amber)
    Reverse Lights - Sylvania Silverstar 7506ST or Error-Free LEDs
    License Plate Lights - C5W Error-Free High-Powered LEDs
  • Turn the engine off and approach the side of the porsch with the burn-out side-marker light. If you are replacing both, start at either side; the replacement procedure is the same.
  • 2 Remove the screws from the plastic fender liner. Peel back the liner to access the area behind the fender.
  • 3 Reach your hand inside to gain access to the side-marker light's backing. Push the backing forward to release the side-marker lens; it's held in place by small clips.
  • 4 Grab the lens on the outer side and turn it over to access the back. Gently turn the bulb to release it from the plastic lens.
  • 5 Pull the bulb straight out to remove it from the electrical socket. Insert a new bulb, but do not touch the glass part of the bulb with your hand.
  • 6 Push the new bulb into the side-marker lens. Turn it clockwise to install it. Push the side-marker lens back into place. Apply gentle pressure to the lens to pop it back into its mount.
  • 7 Replace the screws along the edge of the fender liner.


  • Dec 04, 2010 | 2006 Porsche Cayenne

    1 Answer

    Drivers side front and rear marker (tail light) are not working but the turn signals are and they are the same bulb marker lights


    check bulbs then fuses
    bulbs are dual filiment means there iss 2 different wires inside the bulb and 1 will usually break but the other wont

    Jan 28, 2010 | 2006 Jeep Liberty

    1 Answer

    How to change side marker bulb in 1997 altima


    a53bade.gif

    The marker lights are removed by depressing the tab (arrow) with a thin bladed tool. Take care not to scratch the paint

    1. Disengage the bulb and socket assembly from the lens housing.
    2. Gently grasp the light bulb and pull it straight out of the socket.
    To install:
    1. Before installing the light bulb into the socket, ensure that all electrical contact surfaces are free of corrosion or dirt.
    2. Line up the base of the light bulb with the socket, then insert the light bulb into the socket until it is fully seated.
    3. To ensure that the replacement bulb functions properly, activate the applicable switch to illuminate the bulb which was just replaced. If the replacement light bulb does not illuminate, either it too is faulty or there is a problem in the bulb circuit or switch. Correct as necessary.
    4. Install the socket and bulb assembly into the lens housing.

    Dec 07, 2009 | 1997 Nissan.5 Altima

    3 Answers

    Bulb failure, position light


    Bulb failure, position light means you have a burned out light bulb somewhere. I had the same problem on my 2002 s60. It looked like all the lights were working but I found out that there are several bulbs in the tail lights, so even though the tail lights were working there was in fact a burned out bulb. Look at the bulbs a bit closer and you will probably find one thats bad.

    Oct 06, 2009 | 2006 Volvo S60

    1 Answer

    How do you change the rear side marker lights?


    If you mean replace burned bulbs, find the marker light and locate the wires on the back. Get a good hold on the plug and turn in 45 to 90 degrees and then pull out, replace the bulb and re-install.

    Sep 08, 2009 | 2003 Volvo S40

    1 Answer

    Tiburon GT Limited Fender Side Marker Bulb Replacement?


    You probably have to access the bulb from the back of the bulb housing. The bulb is probably in a socket which plugs into the back. Twist and pull to remove it.

    May 03, 2009 | 1999 Lexus RX 300

    1 Answer

    Need to replace a headlight assembly for a 2006 Subaru Outback.


    No, you just remove the radiator grill and the side marker light and the headlight housing bolts and it comes out. Not a real hard job and is Real straight forward. Good luck and have a good day.

    Mar 27, 2009 | 2006 Subaru Outback

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    269 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Cars & Trucks Experts

    yadayada
    yadayada

    Level 3 Expert

    76630 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22219 Answers

    Randy Ohler

    Level 3 Expert

    14585 Answers

    Are you a Car and Truck Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...