Question about Cars & Trucks

1 Answer

Wiper motor I have a 94 dodge dakota and I removed the three nuts that are holding it to the the fire wall but I can't pull it out. What else do I have to do to remove it?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 21,873 Answers

You have to remove the grille around the blades and disconnect the linkage going to the arms.

Posted on Feb 13, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
Mike258
  • 1498 Answers

SOURCE: wiper motor for 1998 saturn sl

Those bolts are accessed from inside the vehicle, from under the dash. Here's how:

  • Remove the screw caps from the top of the dashboard.
  • Remove the retaining screws
  • Lift the dash from the rear to pull it clear of the retaining clips
  • Disconnect the defroster duct from the heat/AC module and move it toward the glove box.
  • You should now be able to access the the two bolts holding the wiper module in.
  • Remove them
  • You'll need to reposition the the wiper module slightly to disconnect the plug.
Hope this helps

Mike

Posted on Jul 20, 2008

  • 840 Answers

SOURCE: Replace 07 Tahoe Wiper Arm

just pull on it a little harder and it will come off Believe me I have taken off so many of them you can try Wd 40 let it soak and then try again and jiggle it. Please rate my response Thank you very much!

Posted on Jan 28, 2009

  • 1071 Answers

SOURCE: 1995 dodge dakota. Wipers switch only clicks

there are grounds that join behind batter remove battery check for corossion clean up and rejoin splice should work again

Posted on Jul 21, 2009

  • 2 Answers

SOURCE: Windshield wipers don't work but the motor runs . 93 Dodge Dakota

remove wiper arms and then you can raise the hood to remove screws that hold down the vent panel.
now carefully remove vent panel.

Posted on Jan 09, 2010

  • 3600 Answers

SOURCE: Can't remove rear wiper arm on my 2007 Dodge

Just Raise the arm up and rock it back and forth and it will come off if it does not come off on the first try use a little lubercating oil where the threaded shaft sticks out of the arm, contine wiggling till it comes loose. If you need more help let me know, this is the way to do it on most cars makes and modles.

Posted on Jun 29, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wiper arm removal 2000 dodge dakota


lift up the small cap a base of the wiper arm which will reveal a nuit undo this nut and the wiper arm will pull off

Jul 08, 2014 | 2000 Dodge Dakota Quad Cab

2 Answers

MY WINDSHELD WIPER MOTOR WONT WORK ON 1999 DODGE DAKOTA 8 CYLENDER


Here's how to replace the wiper motor.Here's the wiper motor and price.73.99 plus 25.00 core charge.

Dec 29, 2012 | Dodge Dakota Cars & Trucks

1 Answer

My wipers slipped off track of the motor, how do i fix this


That makes no sense

There is only 1 nut holding the wiper linkage
onto the wiper arm.

If you mean someone put the wiper arms on in the
wrong place,remove them & install where they should
be, when the motor is off & in the home pssition.

If you have to get to the linkage, remove the screws for
the metal & plastic vent to cowl grilles

Jul 17, 2011 | 1996 Dodge Dakota

1 Answer

How to replace windwiper motor bushing?


I'am not sure what you mean by the bushing, but I just repaced the wiper motor in my 95 Dakota.
1-remove wiper arms from the pivots.
2-open the hood
3- remove the crowl. there is a line of screws that need to taken out. set the crowl out of the way.
Don't try to remove the motor without removing the crowl. It just won't work.
4- remove the 3 nuts that hold the motor to the firewall.
5 carefully pull out the motor and wiper linkage.
6- remove the nut that hold the linkage onto the motor and remove the linkage. BE CAREFUL you don't want to drop and loose that nut. There is a flat spot on the shaft between the motor and the linkage where a 6" adjutable wrench etc can be put to hold the shaft when taking off the nut.

Follow the above steps in reverse to reinstall. I did use lock tite to make sure the nut doesn't come off the motor shaft.

Feb 06, 2011 | 1995 Dodge Dakota

1 Answer

Need to check windshield wiper motor and its removal on 1989 dodge dakota pickup


Remove Wiper Arms,Metal Grill, Nut on Motor Arm,3 Bolts holding wiper motor.
Dealer has a reman. About $59.00
Remove mounting plate from yours. 3 bolts,turn in old core at dealer

Nov 23, 2010 | 1987 Dodge Dakota

1 Answer

I need to remove a wiper motor from a 62 cadi? how?


there are three bolts holding it against the firewall. disconnect harness, pull motor out towards engine to access wiper transmission nut. remember orientation of actuator arm and remove nut. reverse to install.

Apr 27, 2010 | Cadillac DeVille Cars & Trucks

1 Answer

Windshield wipers don't work but the motor runs . 93 Dodge Dakota


remove wiper arms and then you can raise the hood to remove screws that hold down the vent panel.
now carefully remove vent panel.

Nov 07, 2009 | 1993 Dodge Dakota

1 Answer

Where is the windshield wiper motor on a 2007 Dodge Caravan and how do I replace it?


Wiper Motor: Service and Repair
Removal
REMOVAL
The front wiper motor comes as a unit with a wiper pivot on each end and mounts to a shaft that holds these two inner pivots.
1. Disconnect and isolate the battery negative cable.
2. Remove the wiper arms.
3. Disconnect the washer hose at the in-line connector located near the air cleaner housing.
4. Lift the cowl grille and disconnect the washer hose grommet from the hole in the wiper module. Pull the washer hose and the grommet
completely through the wiper module tub hole.
5. Remove the cowl grille.
CAUTION: Be careful not to scratch the cowl grille on the corner of the hood.
6. Remove the four brace nuts holding the wiper tub to the lower windshield fence.
7. Remove the four bolts underneath the wiper tub inner brace holding the tub to the bulkhead.
8. Remove all four inner support brace mounting nuts and pull the inner braces just free of the mounting studs.
NOTE: The wiper tub will drop down slightly.
9. Disconnect the driver and passenger side wiper link ends at the inner pivots.
10. Remove the two left wiper motor assembly mounting nuts.
11. Remove the two right wiper motor assembly mounting nuts.
12. Partially lift out the wiper motor assembly out of the wiper tub.
13. Disconnect the wiper motor electrical connector.
14. Remove the wiper motor assembly the rest of the way from the wiper tub and remove from vehicle.
--------------------------------------------------------------------------------------------
Wiper Motor: Service and Repair
Installation
INSTALLATION
1. Install front wiper motor assembly onto wiper tub.
2. Connect the electrical connector to the front wiper motor assembly.
3. Install the four mounting nuts. Tighten nuts to 9 Nm (80 in.lbs.).
4. Push the four inner support braces onto the studs and install the four nuts. Tighten the nuts to 9 Nm (80 in.lbs.).
5. Install the four bolts underneath the wiper tub inner braces that hold the wiper tub to the bulkhead. Tighten the bolts to 17 Nm (150 in.lbs.).
6. Install the four nuts holding the wiper tub to the lower windshield fence line. Tighten nuts to 7 Nm (65 in.lbs.).
7. Apply grease to drive link bushings.
NOTE: Make sure to use Mopar(R) approved grease.
8. Attach the driver and passenger side outer wiper linkage to the inner pivots on the front motor assembly and firmly snap into place.
CAUTION: Do not apply too much force to engage link bushing or damage can occur to the drive link bushing.
9. Position the cowl grille in place.
10. Install the washer hose and grommet into the wiper tub.
NOTE: Be sure to properly seat the washer hose grommet into the bottom of the wiper tub.
11. Connect the washer hose at the in-line connector located by the air cleaner housing.
12. Install the cowl grille.
CAUTION: Be careful not to scratch the cowl grille on the corner of the hood.
13. Connect the battery negative cable.
14. Verify that the wiper motor is in the Park position by cycling the wipers system. When done, remove keys from ignition.
15. Install the wiper arms.
16. Align the wiper arms and tighten nuts to 35 Nm (25 ft.lbs.).
17. Install the wiper arm nut caps.

f7c141f.jpg

Sep 13, 2009 | 2007 Dodge Caravan SXT Minivan New Cars

1 Answer

I need to replace my wiper unit . how do you remove it ,just the motor and the shell, the circuit board is ok


You have to remove the wiper arms then the cowling. Remove the retaining nut that holds the arms to the back of the wiper motor. Disconnect the wire connector then remove the 3 bolts that hold the wiper motor to the fire wall. Reverse order to install new motor.

Jul 31, 2009 | 1994 GMC Sierra

1 Answer

1989 dodge dakota pickup heater problem


passenger side on the fir wall you will see a flat black plate with a plug in and two screws holding it in take them out and pull the plate off of the fire wall and you will see that you have a broken wire same problem a couple of weeks ago

Dec 02, 2008 | 1989 Dodge Dakota 2WD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...