Question about Dodge Grand Caravan

Open Question

What is the location for brackets X467B017

I have 2 of these brackets and I am not sure where they go in reassembling my dash board after replacing the heater core.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: 2000 oldsmobile bravada heater core replacement

I have this problem also, what is holding the passenger side part of the top part of the plastic air box to the firewall?

Posted on Oct 20, 2008

Ad
dnewcombe1
  • 1564 Answers

SOURCE: Replacing heater core in 2000 GMC sonoma. Dash is

If the dash is removed you've saved about 9 10ths of the job endurance. Look around, what you believe to be, the perimeter of the heater box. I cannot, and no one else can, tell you exactly where the bolts and nuts that mount the heater box are. Therefore you must viually sixe the box and check outide in the engine compartment and inside under the dash for the mounting bolts.You'll want to start by removing the heater hoses. Then starting at the passenger side engine compartment look for a group of 10mm or 7/16ths nuts retaining the housing and remove them. Do the same inside. The housing is usually held together with screws or clips, it changes year to year. Keep a log or pix of the wires and cables and hoses(vacuum) that are connected to the housing for reassembly. You'll need to "roll" the box out from under the dash depending on how much of the dash has been removed. The core is easy to spot for is has two hoses sticking out, and, is encircled with clips or screws . Also make sure you remove the bracket around the two entry hoses if it has one. Thank you, Dana

Posted on Oct 04, 2009

  • 98 Answers

SOURCE: How to remove the heater core from a VW GolfMK3

there are alot of hidden screws holding the dash in. there are some up across the top of the dash by the windshield and defrost vents. also when you open the doors there are some in there. it is quit a difficult job I really dont recomend doing it yourself but if your not afraid to try and feel confident enough to tackle it good luck. it would be best to have an experienced mechanic do the job but it will cost over three hundred for labor. if you do it yourself go to a parts store that sells haynes repair manuals they cost about twelve dollars and are pretty helpfull.

Posted on Oct 31, 2009

Testimonial: "Thanks for the advice, I will find a manual and if gives some form of help I will do it myself. If not I will pay for it to be done. Thanks."

c17hydro
  • 2984 Answers

SOURCE: heater core

No, you don't have to pull the whole dash board but you have to pull a few panels....here is the steps on how to get to it and remove and replace it:

  1. Disconnect the negative battery cable.
  2. Drain the cooling system and disconnect the heater hoses from the heater core tubes. Plug the hoses and the heater core tubes to prevent coolant leakage.

CAUTION NEVER open, service or drain the radiator or cooling system when hot; serious burns can occur from the steam and hot coolant. Also, when draining engine coolant, keep in mind that cats and dogs are attracted to ethylene glycol antifreeze and could drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantities. Always drain coolant into a sealable container. Coolant should be reused unless it is contaminated or is several years old.


  1. Remove the 3 nuts located below the windshield wiper motor attaching the left end of the plenum to the dash panel. Remove the 1 nut retaining the upper left corner of the evaporator case to the dash panel.

935a10f.gif
Plenum removal—1990-98 vehicles

  1. Disconnect the vacuum supply hose(s) from the vacuum source. Push the grommet and vacuum supply hose(s) into the passenger compartment.
  2. Remove the right and left lower instrument panel insulators.
  1. On 1989 vehicles:
  2. Remove the 3 glove compartment hinge screws, disconnect the check arms and remove the glove compartment.
  3. Loosen the right door sill plate and remove the right side cowl trim panel.
  4. Remove the bolt attaching the lower right end of the instrument panel to the side cowl.
  5. Remove the instrument panel pad as follows:
    • Remove the 2 screws attaching the pad to the instrument panel at each defroster opening. Be careful not to drop the screws into the defroster openings.
    • Remove the one screw attaching each outboard end of the pad to the instrument panel.
    • On Crown Victoria, remove one pad attaching screw near the upper right corner of the glove compartment door.
    • Remove the 5 screws attaching the lower edge of the pad to the instrument panel. Pull the instrument panel pad rearward and remove it from the vehicle.
  6. On 1990-98 vehicles:
  7. Remove all instrument panel mounting screws and pull the instrument panel back as far as it will go without disconnecting any wiring harnesses.
  8. Make sure the nuts attaching the instrument panel braces to the dash panel are removed.
  9. Loosen the right door sill plate and remove the right side cowl trim panel.
  10. If equipped with manual air conditioning, disengage the temperature control cable housing from the bracket on top of the plenum. Disconnect the cable from the temperature blend door crank arm.
  11. If equipped with Automatic Temperature Control (ATC), proceed as follows:
  12. On 1989 vehicles, disconnect the temperature control cable from the ATC sensor.
  13. Detach the vacuum harness line connector from the ATC sensor harness and detach the electrical connector from the ATC servo connector.
  14. On 1990-98 vehicles, remove the cross body brace and disconnect the wiring harness from the temperature blend door actuator. Detach the ATC sensor tube from the evaporator case connector.
  15. Detach the vacuum jumper harness at the multiple vacuum connector near the floor air distribution duct.
  16. Disconnect the white vacuum hose from the outside-recirculating door vacuum motor.

572e87e.gif
Floor air distribution duct removal—1990-98 vehicles
  1. Remove the 2 hush panels.
  2. Remove 1 plastic push fastener retaining the floor air distribution duct to the left end of the plenum.
  3. Remove the left screw and loosen the right screw on the rear face of the plenum and remove the floor air distribution duct.
  4. Remove the 2 nuts from the 2 studs along the lower flange of the plenum.

a3c9f99.gif
Heater core removal—1990-98 vehicles

  1. Carefully move the plenum rearward to allow the heater core tubes and the stud at the top of the plenum to clear the holes in the dash panel. Remove the plenum from the vehicle by rotating the top of the plenum forward, down and out from under the instrument panel. Carefully pull the lower edge of the instrument panel rearward, as necessary, while rolling the plenum from behind the instrument panel.
  2. On 1989 vehicles with ATC, remove the ATC servo from the plenum.
  3. Remove the 4 retaining screws from the heater core cover and remove the cover from the plenum assembly.
  4. Pull the heater core and seal assembly from the plenum assembly.
To install:
  1. Carefully install the heater core and seal assembly into the plenum assembly. Visually check to ensure that the core seal is properly positioned. Position the heater core cover and install the 4 retaining screws.
  2. On 1989 vehicles with ATC, install the ATC servo on the plenum.
  3. Route the vacuum supply hose through the dash panel and seat the grommet in the opening.
  4. Position the plenum under the instrument panel with the register duct opening up and the heater core tubes down. Rotate the plenum up behind the instrument panel and position the plenum to the dash panel. Insert the heater core tubes and mounting studs through their respective holes in the dash panel and the evaporator case.
  5. Install the 3 nuts on the studs along the lower flange and one on the upper flange of the plenum. Install the 3 nuts below the windshield wiper motor to attach the left end of the plenum to the dash panel and the one nut to retain the upper left corner of the evaporator case to the dash panel.
  6. Position the floor air distribution duct on the plenum. Install the 2 screws and plastic push fastener. If removed, position the panel door vacuum motor to the mounting bracket and install the 2 attaching screws.
  7. Connect the white vacuum hose to the outside-recirculating door vacuum motor. Attach the vacuum jumper harness to the plenum harness at the multiple vacuum connector near the floor air distribution duct. Install the floor duct.
  8. If equipped with manual air conditioning, connect the temperature control cable housing to the bracket on top of the plenum and connect the temperature control cable to the temperature blend door crank arm. Adjust the temperature cable.
  9. If equipped with ATC, proceed as follows:
    1. On 1989 vehicles, connect the temperature control cable to the ATC sensor and adjust the cable. Route and attach the vacuum harness connector to the ATC sensor and attach the electrical connector to the ATC servo connector. Do not block the sensor aspirator exhaust port with the excess vacuum harness. Install the ATC sensor tube between the sensor and the evaporator connector.
    2. On 1990-98 vehicles, attach the ATC sensor tube to the evaporator case connector. Install the cross body brace and connect the wiring harness to the blend door actuator.
  10. Install the bolt to attach the lower right end of the instrument panel to the side cowl. Install the right side cowl trim panel and tighten the right door sill plate attaching screws.
  11. On 1989 vehicles, install the instrument panel pad and the glove compartment door. On 1990-98 vehicles, push the instrument panel back into position and install all instrument panel mounting screws. Install the right and left lower instrument panel insulators.
  12. Connect the vacuum supply hose(s) to the vacuum source.
  13. Install the right and left lower instrument panel insulators and install the 2 hush panels.
  14. Unplug the heater core tubes and the heater hoses and connect the heater hoses to the heater core tubes. Fill the cooling system.
  15. Connect the negative battery cable and check the system for proper operation.

Posted on Feb 15, 2010

  • 1024 Answers

SOURCE: How do I remove the dash board of a 2003 Impala to replace heater

you don't have to remove the dash to do this job

Posted on Mar 07, 2010

Testimonial: "What a relief, now I must find out how to replace it."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2004 GMC Sierra 6.6 liter diesel looking for body control modular I think it's under the dash driver side not for sure though and do you have to take the dash out to replace it


it is located under the steering column. you'll only need to remove the knee board cover. it sits in a large bracket. see picture

25684152-fslbviuqxtfaynlex1uhg14h-3-0.png

May 07, 2015 | 2004 GMC Sierra

1 Answer

Location of oil pressure switch 2002 ford windstar


On the 2002 windstar 3.8L it's located under the alternator bracket.
location-oil-pressure-switch-2002-ford-bpnlvvzmft1efcmuowf30xnb-5-0.jpg To see it or replace it.
1. Disconnect the negative battery cable.
2. Remove the serpentine belt from the alternator.
3. Disconnect the battery cable lead on the alternator and connector.
4. Remove the 3 bolts holding the alternator and remove it.


location-oil-pressure-switch-2002-ford-bpnlvvzmft1efcmuowf30xnb-5-2.jpg 5. Loosen the 2 bolts shown ( the bottom one only needs to be out a few threads not as far as shown). Totally remove the top bolt.
6. With a pry bar or large screw driver place behind the bracket and pivot the alternator bracket towards you.
7. Pull connector off switch.

location-oil-pressure-switch-2002-ford-bpnlvvzmft1efcmuowf30xnb-5-5.jpg 8. Use an open end 21mm wrench to remove it. Slow pressure while turning it as not to crack or snap off the switch.
9. Reverse directions for reassembly.

Jul 28, 2013 | Cars & Trucks

1 Answer

Ghostly brake pedal


sounds like you have a bad brake pedal switch or it has come loose from the bracket.

It is located under the drivers side of the dash near the brake pedal lever. It will twist to disconnect it from the bracket. once removed fro the bracket it can be unplugged and replaced.

Feb 15, 2012 | 2003 Dodge Neon

1 Answer

How do I replace the blower motor on a 2002 cadillac deville?


The blower motor is located under the dash on the passenger side.The bottom dash trim panel has to be removed in order to access it.Here are the instructions for removal:

1. Remove the right side sound insulator.
2. Pull back the carpet near the blower motor.
3. Remove the IP compartment.
4. Remove the dash integration module from the bracket.
5. Remove the two rear dash integration module bracket fasteners.
6. Reposition the dash integration module bracket in order to remove the blower motor.
7. Disconnect the electrical connector from the blower motor.
8. Remove the blower motor retaining fasteners.
9. Rotate and remove the blower motor from the vehicle.

Hope this helps; also keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using Fixya, and have a nice day.

Nov 05, 2011 | 2002 Cadillac Deville

1 Answer

Where is the signal flasher located on a 98 chevy cav.


Try below the steering column under the dash area.
1996-00 Vehicles Fig. 3: Turn/hazard flasher location - 1996-00 vehicles 91146g12.gif
The turn and hazard flashers are integrated into one flasher on these models. The flasher is located on a bracket above the brake pedal. Replace the flasher by unplugging the old one, removing it from the bracket, and plugging in the new one.

Oct 08, 2010 | 1998 Chevrolet Cavalier

1 Answer

Where is the body control module located on a 1997 town & country


It is located on the back side of the underdash fuse box (junction block). You remove the lower steering column cover and knee blocker reinforcement. Then remove two plugs from the bottom of the BCM.
Remove the bolts holding the junction block to dash panel mounting bracket. Remove the junction block from the bracket. Remove screws holding the BCM to the junction block. Slide the BCM downward to disengage guide studs on jb from channels on BCM mounting bracket

Mar 23, 2009 | 1999 Chrysler Town & Country

2 Answers

Directional signals screwed up, but my 4 way flashers work.


For this modle and year the turn signal flasher should be mounted in a clip on the right side of the steering column support bracket. The hazard flasher is located under the instrument panel in the module block, on the right side.
Hope this helps,
Regards,

Feb 13, 2009 | 1995 Buick Regal

1 Answer

Replacing the AC Evapoator core 1996 surbuban


more than likely because there are brackets and lots of tubes and ports for the heater under there and it's easier sto remove/install the core with the dash out of the way.

Sep 01, 2008 | 1996 GMC Suburban

1 Answer

How do you remove the dash board on a grand marquis 1996


It is best to remove the front seat then remove the outer trim work on the dash which are fastened with clips. Then remove the screws which hold the heater/AC controls and also the dash panel such as speedometer etc. Remove the lower plastic shield from around the steering column and disconnect the transmission gear position indicator cable. Remove the plastic covering between the steering column and the drivers knees. Their are mounting bolts in the dash and under neath as well and also barbed fasteners. Remove the steering wheel column mounting bolts and it's support brackets. Lower the steering column to the floor. Remove the front door coverings located near the door hinges. Be carefull not to break the fasteners. They pry out of the door weather stripping and then you lift up on them. This will give you access to the lower dash mounting brackets.
With the steering column lowered remove the plastic trim under the windshield. It pops out and givces you access to the front dash mounting screws. disconnest the headlight photo cell control, disconnect the clock, radio and all other pigtail connections that would otherwise interfear with removing the dash. I remove the speedometer electronic cluster as well. Disconnect the AC/heater upper and lower duct work. They are generally fastened with screws and and you have to look for them.
The dash is fastened by the previously mentiond screws located below the windshield and by bolts located near the door which can be seen when the trim is removed also by lower bracket that are braced and is easily identified. These bolts heads are # 10 metric. I have probably forgotten a couple of items but this should get you through the worse of it.
The Mercury Grand Marquis and the Crown Victoria both tend to have blend door problems for the climate control and the dash has to come out to access the blend door control.

Aug 02, 2008 | 1993 Mercury Grand Marquis

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

11 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...