Question about Chrysler 300M
Either the oil pressure switch has failed, or you really do have zero oil pressure. The lack of oil pressure can kill the fuel pump to prevent a fire in a wreck.
You may be able to jumper the fuel pump relay to see it it will start, then figure out the oil pressure issue.
Posted on Feb 13, 2014
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: 1996 Saturn SL, 4 cylinder,
I also had the same problem with my 1996 Saturn SL1, and it also was the starter. I thought it was an electrical problem until, just on a whim I pulled the starter. One of the brushes was almost gone and the commutator looked like hell. I cleaned up the commutator and brushes, and it spun like a top for about a month, until the worn out brush finally died. I also ordered a new starter the same day of the cleaning. Just a word of advice if you will be buying a new starter, go on Ebay Motors and find the store dbelectrical. They sell brand new starters for $49.95 with no core charge plus $12 UPS shipping. So $61.95 vs $150+ at your local parts store....Myself and my friend from work have both bought and daily use starters from them with no problems or complaints to report.
Posted on Jul 31, 2008
SOURCE: 2002 sequioa sudden stall
Often when the battery is disconnected or replaced the computer will lose it's learned idle settings. You could try letting the engine idle in park until the engine temperature comes up to normal and leave it like that for a few minutes, then put the Air con on and let it idle again for a few minutes, then switch the air con off and put it into drive. If it does not stall, let it idle in drive for 2 minutes or so, and then do the same with the Air con on. This should relearn the base idle settings and stop it from stalling on you. Before you carry out this procedure you should make sure that when you replaced the battery you didn't remove any other plugs or knocked anything that may be causing the fault. If you try this procedure and it still stall when you select drive, you will need to get a Mechanic to check the vehicle over.
Hope this helps,
Posted on Nov 02, 2008
If oil pressure is LOW this vehicle has a safety feature that will prevent vehicle from starting.(check oil level before you start) Now what I wan't you to do is to have the oil pressure switch checked or changed. This may be the reason why this vehicle is not starting or it can also be that the actual oil pressure is low. To check the oil pressure of the vehicle you will need an oil pressure guage. Remove the oil pressure switch and connect guage to oil pressure hole and check oil pressure while cranking vehicle.Some pressure testers can be connected to oil filter housing either is fine. If this vehicle has low oil pressure the reasons for that are bad oil pump, clogged oil pump pick up(from lack of oil change/poor mantainence) or bad connecting rod and main bearings but this usually have a warning from before (the engine will sound loud by knocking /clicking-tapping noise) It this was happening you may need to rebuild this engine or replace it. Good luck and Thanks for using FIX YA
Posted on Jan 24, 2009
When you got stuck in the snow did it impact hard (quick stop or small drop like a deeper ditch)? If this is the case it could be the sending unit might have been dammaged in some way. I would have the shop take a look at.
Posted on Feb 19, 2009
Tips for a great answer:
Aug 06, 2016 | 2004 Hyundai Santa Fe
Feb 13, 2014 | 2000 Chrysler 300M
Mar 04, 2017 | Cars & Trucks
Jul 16, 2017 | Cars & Trucks
Nov 01, 2013 | Subaru Impreza Cars & Trucks
Oct 19, 2012 | 2005 Chrysler PT Cruiser
May 16, 2012 | 2000 Mitsubishi Galant
Jan 22, 2009 | 2003 Mini Cooper
75 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: