Question about 1998 Chevrolet Metro

1 Answer

Adjust both belts on 1998 chevy metro 1.0 3 cyl

Remove and replace air conditioner belt and fan belt

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 121 Answers

Posted on Feb 13, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

dgjtex
  • 405 Answers

SOURCE: chevy silverado 2000 serpentine belt replacement?

Mike, the belt routing should be on a sticker under your hood, these use a spring belt tensioner and it is easiest to us a 3/8 or 1/2 breakover to pull the tensioner back then the belt is easily removed and replaced, please do not rate me at all if it is not a fixya, thats the only reason do this is for my score. Thanks, and merry Christmas.

Posted on Dec 22, 2008

chrisxxxx
  • 1 Answer

SOURCE: chevy van g20 replace fan belt

how do i replace the fan belt on my 71 chevy pick up

Posted on Jan 09, 2009

DAD5bbbbg
  • 111 Answers

SOURCE: setting timing belt on 99 chevy metro

The best thing that you could do is to buy a Chilton's Manual for your car. You can buy them at any parts store and they don't coast much. This way you can have it for any other problems you might have later on. Putting a timing belt on is a step by step project, getting a book will tell you every thing you need to know.

Posted on Mar 29, 2009

  • 1 Answer

SOURCE: 1998 chevy cavalier Alternator Drive Belt diagram

Check out this link... better than a diagram, a photo.

http://www.automotiveforums.com/vbulletin/showthread.php?t=309192

note: on my screen this guy's "purple" circle looks more like a light blue, maybe lavender.

Posted on Jun 27, 2009

  • 20 Answers

SOURCE: Diagram of Serpentine Belt 1998 Chevy Cavalier

diagram should be on the radiator shroud / top of radiator

Posted on Jan 10, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fan belt diagram


1989 Belts

Print


INSPECTION

All Models
Belt tension is very important, as a belt that is too tight will put too much stress on the bearings of the components it drives, causing them to wear out prematurely. A belt that is too loose will slip, causing (1) the belt to wear out quickly due to friction heat, and (2) inefficient alternator, air pump, cooling fan or air conditioner operation because much of the turning power supplied by the main drive pulley is lost.
The belts should be inspected and/or adjusted at 2,000 miles (3,221 km) and then every 4,000 miles (6,441 km). First, make sure that the belt is properly positioned in the pulley. Check the pulleys for damage. Inspect the belts for cracks and signs of fraying. These usually develop on the inner surface and extend into the backing or outer surface of the belt. Check also for glazing, a completely smooth appearance which indicates slippage. A belt that is in good shape will have a slightly grainy appearance like cloth. Replace belts that show cracks or glazing.
Check belt tension. Apply pressure with your thumb at the mid-point between two pulleys, and the belt should stretch or deflect about 1 / 4 - 1 / 2 in. (6-13mm). If the belt is too tight or too loose, adjust/replace as necessary.


ADJUSTING

Except RX-7
See Figures 1, 2 and 3
To adjust belts, first locate the mounting bolt on the air pump or alternator (each has its own belt and adjusts to permit that belt to be tensioned correctly). This bolt attaches the unit to the engine and has a nut on the end. Put a wrench on either end and loosen the bolt until there is practically no tension on it. Then, loosen the adjusting bolt, which is located on the opposite side of the unit and which passes through a slot. Pull the alternator or air pump away from the engine and tighten the adjusting bolt just enough to hold the unit while you check tension. Repeat the adjustment procedure until the belt deflects the proper amount, then fully tighten the adjusting and mounting bolts. Avoid too much belt tension or overtightening of bolts. A new belt should be tensioned just slightly more (about 0.4 in. or 10mm deflection) and checked after several hundred miles of operation to make sure that tension is still adequate. (Tension is lost very rapidly until a new belt is broken in.)


0900c1528004e5dd.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 1: Some engines utilize an idler pulley with a locknut at its center


0900c1528004e5de.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 2: After loosening the idler adjuster locknut, turn the adjusting bolt clockwise to increase belt tension or counterclockwise to decrease it


0900c1528004e5df.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 3: On some GLC engines equipped with power steering, the pump pulley uses a slotted adjusting bar, adjusting bolt and locknut to adjust belt tension
Late model GLCs, 323s, 626s, MX-6s and 929s may use an adjusting bolt on either the idler pulley (a pulley which is not directly associated with any of the accessories) or on the power steering pump itself. This bolt makes adjustment much easier because you don't have to hold the accessory under a great deal of tension while tightening the mounting bolts.
On models where the idler pulley has a locknut at its center, simply loosen the locknut, then turn the adjusting bolt clockwise to increase belt tension or counterclockwise to decrease it or remove the belt. Do not forget to retighten the locknut when tension is correct, or vibration may cause it to fall off. Recheck the tension with the locknut tightened and readjust if necessary.
To adjust the power steering pump pulley on the GLC, loosen the slotted adjusting bar bolt, the mounting bolt across from it, and the locknut at the bottom of the adjusting bolt. Turn the adjusting bolt counterclockwise to remove the belt or reduce tension, and clockwise to increase it. When tension is correct, tighten the adjusting bolt locknut, adjusting bar bolt, and pump mounting bolt.
On 626, MX-6 and 929 models with a 4-ridge or 5-ridge ribbed type V-belt driving both the air conditioner and power steering pump, belt tension is much greater. With a used belt, deflection should only be about 1 / 4 in. (6.35mm).
RX-7
See Figures 4, 5 and 6
The RX-7 may be equipped with as many as three or four separate drive belts. The belts are arranged at the front of the engine and drive the cooling fan/water pump, alternator, power steering pump, emission control air pump and air conditioner compressor (if so equipped).


0900c1528004e5e0.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 4: Checking belt tension on 1979-85 RX-7
Check the tension of each belt at the arrows numbered 1, 2, 3 and 4 (depending on year) shown in the illustration. Press on the belt with your thumb using moderate pressure (about 22 lbs.). The belts should give or deflect the amounts shown in the chart.


0900c1528004e5e1.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 5: Checking belt tension on 1986-89 RX-7


0900c1528004e5e2.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 6: RX-7 belt deflection limits
Use the following appropriate procedure and illustration to make drive belt adjustment(s).
ALTERNATOR AND AIR PUMP
See Figure 7

  1. Slightly loosen the stationary pivot bolt on the alternator or air pump.
  2. Loosen the adjusting bolt.
  3. Using a piece of wood (tool handle, etc.) as a prybar, move the alternator or air pump outward or inward until the proper deflection is obtained.



0900c1528004e5e3.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 7: Adjusting alternator drive belt tension on 1986-89 RX-7
When prying on the alternator or air pump, make sure the prybar is anchored against the engine case and not against a component (distributor cap, etc.) which could break.

  1. Tighten the adjusting bolt. Remove the prybar and tighten the pivot bolt.

AIR CONDITIONING COMPRESSOR AND POWER STEERING PUMP
See Figures 8 and 9
  1. Loosen the locknut on the idler pulley, if so equipped.
  2. Turn the adjusting bolt until the proper tension is reached.



0900c1528004e5e4.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 8: Adjusting air conditioning compressor drive belt tension on 1986-89 RX-7

  1. Tighten the locknut and recheck the belt tension.



0900c1528004e5e5.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 9: Adjusting power steering pump drive belt tension on 1986-89 RX-7


REMOVAL & INSTALLATION

All Models

  1. Loosen the accessory being driven and move it on its pivot point to free the belt.
  2. Remove the belt. If an idler pulley is used, it is often only necessary to loosen the idler pulley to provide enough slack to remove the belt.

To install:
  1. After the new belt is in place and properly tensioned, start the engine and allow it to run for about five minutes to seat the new belt.
  2. Stop the engine and recheck the belt tension. Adjust as necessary.

On engines with many driven accessories, other belts may have to be removed to access the one being replaced.

May 27, 2012 | 1989 Mazda 323

1 Answer

2000 1.3l chevy metro cam and crank shaft position sensor resistance


00 chevy metro 1.3l just replace head gasket and had head work new timing belt timing/compressing good reassembled adjusted valve attemp to crank and #1 #3 s/plug foul #2 #4 good need help

Mar 03, 2011 | Chevrolet Metro Cars & Trucks

1 Answer

How to replace timing belt on 3 cyl geo metro


remove accesory belts remove carank pulley remove t belt covers
set cyl 1 TDC change belt

Apr 24, 2010 | 1995 Geo Metro

1 Answer

How do i take off the old water pump on 1996 geo metro 4 cyl?


Removal & Installation
  1. Disconnect the negative battery cable.
  2. Drain the cooling system.
  3. Remove the air cleaner.
  4. Remove the suction pipe bracket for the A/C compressor, if equipped.
  5. Loosen but do not remove the 4 water pump pulley bolts.
  6. Raise and safely support the vehicle.
  7. Remove the lower splash shield.
  8. Remove the A/C compressor drive belt, if equipped.
  9. Remove the alternator drive belt.
  10. Remove the crankshaft and water pump pulleys.
  11. Remove the timing belt.
  12. Remove the oil level dipstick and tube.
  13. Remove the alternator adjusting bracket from the water pump.
  14. Remove the water pump rubber seals.
  15. Remove the water pump mounting bolts and nuts and remove the water pump from the engine.


ae1b66e.gif
Water pump mounting location

  1. Clean the gasket mating surfaces thoroughly.
  2. Check the water pump by hand for smooth operation. If the pump does not operate smoothly or is noisy, replace it.
  3. Install the pump using a new gasket. Tighten the bolts to 115 inch lbs. (13 Nm).
  4. Install new rubber seals.
  5. Install the upper alternator adjusting bracket and tighten the bolt to 17 ft. lbs. (23 Nm).
  6. Install the oil level dipstick and tube.
  7. Install the timing belt.
  8. Install the water pump and crankshaft pulleys. Leave the water pump pulley bolts hand-tight.
  9. Install the alternator drive belt.
  10. Install the lower alternator cover plate and tighten the bolts to 89 inch lbs. (10 Nm).
  11. Install the A/C compressor drive belt, if equipped.
  12. Install the lower splash shield and lower the vehicle.
  13. Tighten the water pump pulley mounting bolts to 18 ft. lbs. (24 Nm).
  14. Adjust the water pump drive belt tension and tighten the alternator adjustment bolt to 17 ft. lbs. (23 Nm).
  15. Install the suction pipe bracket for the A/C compressor, if equipped.
  16. Install the air cleaner.
  17. Refill the cooling system.
  18. Connect the negative battery cable.
  19. Start the engine and check for leaks.


83667f6.gif Water pump assembly showing rubber seal location


  1. Disconnect the negative battery cable.
  2. Drain the cooling system.

    CAUTION When draining the coolant, keep in mind that cats and dogs are attracted by the ethylene glycol antifreeze, and are quite likely to drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantity. Always drain the coolant into a sealable container. Coolant should be reused unless it is contaminated or several years old.

  3. Remove the air cleaner assembly.
  4. Loosen but do not remove the four coolant pump pulley bolts.
  5. Raise and support the vehicle safely.
  6. Remove the lower splash shield.
  7. Remove the air conditioner compressor drive belt.
  8. Remove the lower alternator cover plate bolts, loosen the alternator adjusting bolt, and remove the drive belt.
  9. Remove the crankshaft pulley.
  10. Remove the coolant pump pulley.
  11. Remove the timing belt.
  12. Remove the oil level dipstick and guide tube.
  13. Remove the alternator adjusting bracket from the water pump.
  14. Remove the water pump rubber seals.
  15. Remove the water pump mounting bolts and nuts. Remove the water pump from the vehicle.
To install:
  1. Clean the gasket mating surfaces thoroughly.
  2. Check the water pump by hand for smooth operation. If the pump does not operate smoothly or is noisy, replace it.
  3. Install the pump using a new gasket. Tighten bolts to 115 inch lbs. (13 Nm).
  4. Install new rubber seals.
  5. Install the upper alternator adjusting bracket and tighten bolt to 17 ft. lbs. (23 Nm).
  6. Install the oil level dipstick and guide tube.
  7. Install the timing belt.
  8. Install the water pump pulley and leave the bolts hand tight.
  9. Install the crankshaft pulley.
  10. Install the water pump/alternator drive belt.
  11. Install the lower alternator cover plate and tighten bolts to 89 inch lbs. (10 Nm).
  12. Install the air conditioner compressor drive belt by releasing the tensioner pulley and installing belt.
  13. Install the lower splash shield and lower vehicle.
  14. Tighten water pump pulley mounting bolts to 18 ft. lbs. (24 Nm).
  15. Adjust the water pump drive belt tension and tighten alternator adjustment bolt to 17 ft. lbs. (23 Nm).
  16. Install the air cleaner assembly.
  17. Refill the cooling system.
  18. Connect the negative battery cable.
  19. Start the engine and allow it to reach operating temperature. Check for leaks and refill cooling system as necessary.

Mar 06, 2010 | 1996 Geo Metro

1 Answer

I need a diagram on how to replace a 2001 chevy metro alternator.


2001 Chevrolet Metro 1.3L MFI SOHC 4cyl

Alternator - Removal & Installation
  1. Before servicing the vehicle, refer to the precautions section.
  2. Remove or disconnect the following:
    Negative battery cable Air cleaner assembly Alternator electrical connectors Accessory drive belt Upper and lower mounting bolts Alternator
To install:
  1. Install or connect the following:
    Alternator and the bolts, do not tighten the bolts at this time
  2. Install the alternator belt and adjust the tension until a deflection of 0.24-0.31 inch (6-8mm) deflection with 22 lbs. (10 kg) of pressure exerted when installing a used belt. On a new belt the belt deflection should be 0.20-0.27 inch (5-7mm) with 22 lbs. (10 kg) of pressure exerted.
    Alternator electrical connectors, then torque the alternator bolts to 17 ft. lbs. (23 Nm) Air cleaner assembly Negative battery cable
  1. Before servicing the vehicle, refer to the precautions section.
  2. Remove or disconnect the following:
    Negative battery cable Accessory drive belt Alternator electrical connectors Alternator
To install:
  1. Install the alternator and hand-tighten the bolts.
  2. Install the alternator belt and adjust the tension until a deflection of 0.24-0.31 inch (6-8mm) deflection with 22 lbs. (10 kg) of pressure exerted when installing a used belt. On a new belt the belt deflection should be 0.20-0.27 inch (5-7mm) with 22 lbs. (10 kg) of pressure exerted.
  3. Install or connect the following: Upper alternator bolt to 18 ft. lbs. (25 Nm) Lower alternator bolt to 40 ft. lbs. (54 Nm) Alternator electrical connectors Accessory drive belt Negative battery cable

    459fdba.jpg
    Fig. Exploded view of the alternator-Metro and Prizm models
Hope thats help (remember rated this).

Feb 18, 2010 | 2001 Chevrolet Metro

1 Answer

I need a belt diagram for a 91 Geo Metro. I am replacing the alternator belt, but need to get the first belt off.I do not know where the belt tension adjustment bolt is for the first belt.


I believe the air conditioner belt tensioner bolt is underneath the mounting bracket on the compressor, then you can remove the alternator belt by loosening the two bolts from underneath on the alternator then loosen the top bolt and be careful prying the alternator inward to loosen the belt you can short a wire connection. Remove one of the battery cables to be safe!

Sep 24, 2009 | 1991 Geo Metro

1 Answer

I want to disconnect the air conditioner on my 1998 Ford E-250 6 cyl engine. Exactly which fuse do I remove?


you want to remove the AC fan belt and buy a new belt to replace the old one so that you do not lose horse power form the parisitic darin caused by the belt and compressor.

Aug 18, 2009 | 2003 Ford E250

1 Answer

How Do i replace Water Pump on 98 Chevy Metro


  1. Remove the negative battery cable.
  2. Drain the engine cooling system.
  3. Remove the air cleaner assembly.
  4. Remove the A/C compressor suction pipe bracket (if equipped).
  5. Loosen four water pump pulley bolts. Do not remove the bolts.
  6. Raise the vehicle. Support the vehicle. Remove the right lower splash shield.
  7. Remove the right lower splash shield.
  8. Remove the A/C compressor drive belt (if so equipped) by releasing the tensioner pulley and removing the belt from the crankshaft and compressor pulleys.
  9. Loosen the generator adjusting bolt (1), pivot the generator and remove the water pump/generator drive belt.
  10. Remove the crankshaft pulley.
  11. Remove the water pump pulley (four bolts).
  12. Remove the timing belt.
  13. Remove the oil level indicator (dipstick) guide tube.
  14. Remove the upper generator adjusting bracket from the water pump (one bolt).

    1. Remove the rubber seals from the water pump.
    2. Remove the water pump mounting bolts and nuts.
    3. Remove the water pump and gasket from the vehicle.
    4. Clean the water pump and the gasket mating surfaces.
    5. Install the water pump.
    6. Secure the water pump with mounting nuts and bolts. Tighten Tighten the water pump mounting nuts and bolts to 13 Nm (115 ft. lbs.).
    7. Install new rubber seals (1) to the water pump (2).
    8. Install the upper generator adjusting bracket to the water pump (one bolt).
        • Tighten the upper generator mounting bracket bolt to 23 Nm (17 ft. lbs.).
      1. Install the oil level indicator (dipstick) guide tube.
      2. Install the timing belt.
      3. Install the water pump pulley.
      4. Finger-tighten the four bolts.
      5. Install the crankshaft pulley.
      6. Install the water pump/generator drive belt to the crankshaft, water pump and generator pulleys.

Nov 20, 2008 | 1998 Chevrolet Metro

1 Answer

How to replace alternator on 98 chevy metro 4 cylinder


  1. Disconnect the negative (-) battery cable. CAUTION: Failure to observe Step 1 may result in a serious personal injury. It a tool is shorted at the generator lead, the tool will become hot enough to cause a serious burn .
  2. Remove the air cleaner assembly.
  3. Remove the rubber protector, the nut and the electrical connector from the generator B terminal.
  4. Remove the upper mounting bolt (1).
  5. Remove the drive belt.
  6. Remove the 2 lower generator mounting bolts.
  7. Remove the generator.
    1. Install the generator.
    2. Install the 2 lower mounting bolts finger-tight.
    3. Install the upper mounting bolt (1) finger-tight.
      1. Install the drive belt.
        • Adjust the drive belt to obtain a 68 mm (0.24-0.31 in) deflection with 10 kg (22 lbs) pressure exerted when reinstalling a used belt.
        • Adjust the drive belt to obtain a 5-7 mm (0.20-0.27 in) deflection with 10 kg (22 lbs) pressure exerted when reinstalling a new belt.
      1. Tighten the generator upper mounting bolt. NOTE : Refer to Fastener Notice in Cautions and Notices. Tighten Tighten the generator upper mounting bolt to 23 N.m (17 lb ft) .
      2. Tighten the generator lower mounting bolts.
      Tighten
      Tighten the generator lower mounting bolts to 23 N.m (17 lb ft) .
      1. Connect the electrical connector to the generator B terminal. Secure the connector with one nut and the rubber protector. Tighten Tighten the electrical connector nut to 8 N.m (71 lb in) .
      2. Install the air cleaner assembly.
      3. Connect the negative (-) battery cable. Tighten Tighten the negative (-) battery cable to 15 N.m (11 lb ft) .

Nov 18, 2008 | 1998 Chevrolet Metro

2 Answers

How to change water pump in 1996 geo metro?


I've found the Haynes Repair Manual that you can get at Auto Zone to be the best one there is. They have step by step instructions with pictures on repairing or replacing just about anything on your auto. You can get them for around $20 - 25. Is yours a 3 or 4 cylinder? Auto Zone has a new service where you can actually look up repair instructions for your vehicle with pictures. Here's the instructions for a 3 cylinder for your year, make and model:
  1. Disconnect the negative battery cable.
  2. Drain the cooling system.
CAUTIONWhen draining the coolant, keep in mind that cats and dogs are attracted by the ethylene glycol antifreeze, and are quite likely to drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantity. Always drain the coolant into a sealable container. Coolant should be reused unless it is contaminated or several years old.
  1. Remove the air cleaner assembly.
  2. Loosen but do not remove the four coolant pump pulley bolts.
  3. Raise and support the vehicle safely.
  4. Remove the lower splash shield.
  5. Remove the air conditioner compressor drive belt.
  6. Remove the lower alternator cover plate bolts, loosen the alternator adjusting bolt and remove the drive belt.
  7. Remove the crankshaft pulley.
  8. Remove the coolant pump pulley.
  9. Remove the timing belt.
  10. Remove the oil level dipstick and guide tube.
  11. Remove the alternator adjusting bracket from the water pump.
  12. Remove the water pump rubber seals.
  13. Remove the water pump mounting bolts and nuts. Remove the water pump from the vehicle.
To install:
  1. Clean the gasket mating surfaces thoroughly.
  2. Check the water pump by hand for smooth operation. If the pump does not operate smoothly or is noisy, replace it.
  3. Install the pump using a new gasket. Tighten bolts to 115 inch lbs.. (13 Nm).
  4. Install new rubber seals.
  5. Install the upper alternator adjusting bracket and tighten bolt to 17 ft. lbs.. (23 Nm).
  6. Install the oil level dipstick and guide tube.
  7. Install the timing belt.
  8. Install the water pump pulley and leave the bolts hand tight.
  9. Install the crankshaft pulley.
  10. Install the water pump/alternator drive belt.
  11. Install the lower alternator cover plate and tighten bolts to 89 inch lbs.. (10 Nm).
  12. Install the air conditioner compressor drive belt by releasing the tensioner pulley and installing belt.
  13. Install the lower splash shield and lower vehicle.
  14. Tighten water pump pulley mounting bolts to 18 ft. lbs.. (24 Nm).
  15. Adjust the water pump drive belt tension and tighten alternator adjustment bolt to 17 ft. lbs.. (23 Nm).
  16. Install the air cleaner assembly.
  17. Refill the cooling system.
  18. Connect the negative battery cable.
  19. Start the engine and allow it to reach operating temperature. Check for leaks and refill cooling system as necessary.

Jul 17, 2008 | 1996 Geo Metro

Not finding what you are looking for?
1998 Chevrolet Metro Logo

93 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...