Question about 2007 Hyundai Santa Fe Limited

1 Answer

How to remove head light?

I need to remove the head light assembly can you please tell me how to remove the whole head like assembly?

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 1 Answer

I have removed the entire assembly before and it wasn't very difficult. From memory there are a few screws to undo and then the whole assembly slides out. I found the directions in the manual in the section on replacing headlight globes.

Posted on Mar 29, 2014


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do I take the head light assembly out?

pls,i want my email open now for me to check my emails ok pls???

Feb 12, 2014 | 2007 Hyundai Santa Fe Limited

1 Answer

Replace head light How do you get the head light assembly out?  Is there a bolt at the bottom some place?

Get the replacement bulb first. The bulb should turn out half a turn to relaese from the backside. You should not have to remove the whole assembly.

Jan 06, 2010 | 2008 GMC Acadia

1 Answer

2004 chve trailblazer tell me how can i chinge the headlight light

you need to remove the grill, a small flat head screw driver will do the trick, you will need to push down on the clips under the hood and pull lightly from the head light assembly and grill just comes off. Then you will need to pull up the two clips on the top corners of the head light assembly. this will free up the assembly this way you can easily remove the bulb and replace it.

Nov 10, 2009 | 2004 Chevrolet TrailBlazer

1 Answer

Removing the whole pop head lights assembly from my 1997 corvette

Raise the headlights, either with the switch or manually by turning the knob on the headlight motor counter-clockwise.
Unplug the lights NOW to avoid an accidental closing on your fingers,
Remove the 3 philips screws holding the black plastic surrounding the headlights, and slide it forward, there is a small clip on the top that helps hold it to a corresponding clip at the top of the headlight,
Look inside the cavity and you can see the 5 nuts/bolts ( 6 on later years ) that need to be removed,
If you are on the driver's side you can now remove the whole assembly, on the passenger's side you must first unplug the headlight door control module.

Aug 25, 2009 | 1998 Chevrolet Corvette

1 Answer

How to replace low beam head light

you have to either pull out two retaing pins and remove the lamp assembly on one style grill others need the whole grill removed

Jul 24, 2009 | 1994 GMC Sierra

1 Answer

1993 honda perlude Receiver Drier removal

ok well theres scews on the out side to remove the head light it self and be hind that you will find the scews to remove the assembly

Mar 20, 2009 | 1986 Honda Prelude

1 Answer

I can't find the access to the the head lamps to my 2001 impala t

Unless you can fit your hand in between the body an the back side of the headlight assembly, you probably are going to have t remove the whole assembly, alot of vehicles now are that way, the whole assembly has to be removed to access the headlight bulb. Hope this helps.

Mar 17, 2009 | 2005 Chevrolet Venture

3 Answers

How to change the headlight

pg 5-43 in your drivers manual tells you how. You just need to remove the 2 hex bolts on top, then grab the whole assembly and pull it at an angle up, and towards the radiator. after you release the assembly you'll see the wire for the headlamp, Disconnect the bulb base from the wireing harness by lifting the plastic tab, remove the black retainer by turning it counterclockwise. Turn the bulb socket for the headlamp counterclockwise to remove. Do everything in reverse to put it back together.

Feb 14, 2009 | 2006 Pontiac G5

1 Answer

Remove head light to replace bulbs

You have to be careful-the whole assembly snaps in and out

Sep 22, 2008 | 1999 Jeep Grand Cherokee

Not finding what you are looking for?
2007 Hyundai Santa Fe Limited Logo

84 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts


Level 3 Expert

79077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides