Question about 2006 Toyota Tundra

Open Question

Need to reprogram 2514 astrostart remote

How do I reprogram a 2514 astrostart remote.

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Can I connect a astrostart remote key to my '08 Chevy uplander?


you need to notify astrostart since their are 4 different types of systems and give them the information on all the specs for your vehicle and they will advise how much and what additional components are needed

Jun 29, 2016 | 2008 Chevrolet Uplander

1 Answer

I have an Astrostart hst5224, It will star then immediately shut off. My jeep is A manual transmission


[PDF]MODEL RSS-5225 - DirectedDealers.com

www.directeddealers.com/manuals/OG/Astrostart/RSS-5225_OG-Eng.pdf
Immediately report any malfunction to the AstroStart dealer that performed the ... Always turn off the main switch when not using the remote starter for .... The startmodule will inform you of the status of door locks, the alarm and of the engine. .... If the trunk is opened for more than 5 minutes, the system switches to the.

How do you reprogram an AstroStart remote HST5224

www.answers.com > Wiki Answers > Categories > Cars & Vehicles
In order to reprogram an AstroStart HST5224 remote, you must putthe key in the ignition ... lamp) b, press and hold UNLOCK button, after 1 second key LED will flash once c, .... C. Turn the ignition to ON (Do NOT Start) then back to OFF. ... B.Immediately after letting go of the lock and unlock buttons, press the lock button by ..

Nov 24, 2015 | 2007 Jeep Wrangler Unlimited Rubicon 2...

1 Answer

Astrostart why do I have to push my button on my remote 3 or 4 times before the signal on the remote blinks to start my truck


Sounds as if ur remote button is not contacting the buttons inside your remote properly. Depending on the age of the remote, the contacts could be worn out or "burnt". You can try opening up the remote and use a scotch abrasive pad to clean the contacts. Or if it's a new remote, it could be a low quality device that needs to be replaced with a better quality remote. U may want to look into purchasing a new remote if yours is worn, cleaning the contacts doesn't always work and a new one may be the best choice for your issue. Hope this helps.

Oct 15, 2015 | Cars & Trucks

2 Answers

Reprogram astrostart j5f tx2000


Get under the dash or where the unit is located.
You will see 8 or 9 dip switches on the unit with an LED beside them.
Turn switch 1 and 8 on.
Press and release the brake. (LED will flash)
Press and hold start button on remote. (LED will flash and parklights will flash once.
Turn switch 1 and 8 to off.
Press and release the brake (LED will flash once)
In future would be a good idea to supply vehicle details etc as can sometimes be a known condition , that saves time looking it up , good luck

Nov 18, 2014 | Cars & Trucks

1 Answer

My astrostart system will only start my truck with a key in the ignition. The batteries in the fob had gone dead and when I replaced them, it did not start at all. I went through the reprogram process...


take the key and the vehicle to a service dealer as sometimes it is necessary to have the key reprogrammed to the immobiliser in the CPU program

Nov 14, 2014 | Cars & Trucks

1 Answer

AstroStart remote starter system will start my vehicle but then does not keep running. Runs less than 10-15 seconds.


that is a adjustment that has to be programed into youre remote start system. it can be found in the owners manual. it just needs to be programed

Dec 02, 2013 | 2005 Chrysler 300

2 Answers

Astrostart won't start the car


You may need to reset the system.

SEQUENCE ACTIVATED BY THE PARKING BRAKE .
1. While engine is running (key in ignition switch), apply the brakes and hold the pedal down.
2. Move gearshift lever to neutral.
3. Apply the parking brake Once Twice
Note: The system can be set - at time of installation - to require that the parking brake be applied once or twice.
If set for two actuations, pause one second between the two.
4. Remove key from ignition (the system keeps the engine running).
5. Exit the vehicle.
6. Within 60 seconds, close all doors.
7. The system will stop the engine and blink the parking brakes once to confirm the sequence is valid (vehicle is
ready for a remote start command).
SEQUENCE ACTIVATED BY THE REMOTE CONTROL
1. While engine is running (key in ignition switch), apply the brakes and hold the pedal down.
2. Move gearshift lever to neutral.
3. Apply parking brake.
4. Send the start command (Model 801 & 2101 - Model 903 ).
5. Remove key from ignition (the system keeps the engine running).
6. Exit the vehicle.
7. Using the remote, send the STOP command. The system will stop the engine and parking lights will blink once
to confirm that the sequence is valid (vehicle is ready for a remote start command).
http://www.astrostart.com/Support/Guides.aspx

Nov 27, 2012 | Cars & Trucks

1 Answer

Astrostart 2100 autostart will not work all the time


It would almost appear that your battery is weak. If the engine doesn't freely turn over the remote start will not work because it recognizes the problem. I would also hope that you plug in your block heater when it's really cold.

Feb 06, 2012 | Chrysler Town and Country Cars & Trucks

1 Answer

Vehicle will not shut off after key is removed.


try starting it with the key and then try to shut it off with the key...

Jan 10, 2009 | 2003 Chevrolet Tahoe

Not finding what you are looking for?
2006 Toyota Tundra Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...