Question about Hyundai Tucson

Open Question

Replace front axle 2011 hyundai tuson

Want to replace old axle boot on tucson and need to remove cv joint how to

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

2tone2
  • 7 Answers

SOURCE: what is the procedure to

You don't need the special tools that they use in this procedure, you can use a hammer and a block of wood to get the axle out of the hub and you can use a pry bar to get the axle out of the transmisson.



Notice: Care must be exercised to prevent the constant-velocity joints from being over-extended. When either end of the drive axle is disconnected, over-extension of the joint could result in separation of internal components and possible joint failure. Drive axle joints and seals should be protected any time service is performed on or near the drive axles. Failure to observe this can result in interior joint or seal damage and possible joint failure.
Notice: Prior to removal of drive axle assembly, cover all sharp edges in the area of the drive axle with shop towels so that the seal is not damaged during removal.
Removal Procedure

  1. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
  2. Remove the tire and the wheel assembly. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.
  3. Place shop towels underneath the outer joint to protect from any sharp edges.

  4. 141983.gif
    tif.gif
  5. Insert a drift (1) into the caliper and the rotor to prevent the rotor from turning.
  6. Remove the drive axle nut (2) and the washer.
  7. Remove the lower ball join from the steering knuckle. Refer to Lower Control Arm Ball Joint Replacement in Front Suspension. If you remove the right axle, turn the wheel to the left. If you remove the left axle, turn the wheel to the right.
  8. Disconnect the wheel speed speed sensor harness. Refer to Wheel Speed Sensor Replacement in Antilock Brake System.
  9. Disconnect the stabilizer link from the lower control arm. Refer to Stabilizer Shaft Link Replacement in Front Suspension.

  10. 442393.gif
    tif.gif
  11. Use the J 28733-B in order to disengage the axle from the hub and the bearing.
  12. Separate the hub and the bearing assembly from the drive axle. Move the strut and the knuckle assembly rearward.

  13. 500285.gif
    tif.gif
  14. Remove the inner joint from the transaxle using J 33008 attached to J 29794 and J 2619-01 for the intermediate shaft, if equipped.
Installation Procedure Notice: Prior to installation of drive axle assembly, cover all sharp edges in the area of the drive axle with shop towels so that the seal is not damaged during installation.
Any time the front halfshaft is removed, the transmission (the halfshaft male and female shank) and the knuckle sealing surfaces should be inspected for debris or corrosion.
If debris or corrosion are present on the sealing surfaces, clean them with a 320 grit cloth or equivalent. Transmission fluid may be used to clean off any of the remaining debris. The surface should be wiped dry, and the halfshaft should be reinstalled free of any debris or corrosion buildup.

    189013.gif
    tif.gif
  1. Install the drive axle (2) into the transaxle (1). Place a non-ferrous drift into the groove on the joint housing and then tap until the drift is seated. Be careful not to damage the axle seal or dislodge the seal garter spring when you install the axle.

  2. 442471.gif
    tif.gif
    Important: Verify that the drive axle is seated by grasping on the inner joint housing and pulling outboard.
  3. Install the drive axle (1) into the hub and bearing assembly (2).
  4. Install the stabilizer link. Refer to Stabilizer Shaft Link Replacement in Front Suspension.
  5. Connect the wheel speed sensor harness. Refer to Wheel Speed Sensor Replacement in Antilock Brake System.
  6. Install the lower ball joint to the steering knuckle. Refer to Lower Control Arm Ball Joint Replacement in Front Suspension.

  7. 141983.gif
    tif.gif
    Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.
  8. Install the washer and the new drive axle nut (2).
  9. Insert a drift (1) into the caliper and the rotor in order to prevent the rotor from turning.
    Tighten
    Tighten the drive axle nut to 200 N·m (144 lb ft).
  10. Install the tire and the wheel assembly. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.
  11. Lower the vehicle

Posted on Nov 02, 2008

  • 14 Answers

SOURCE: 94 Geo Prizm CV or driveaxle?

on this type of vehichle, you have two axles in the front; one going to each side. Chances are that the boot at the axle joint was torn and that is why you are having problem. In teh past people used to replace the boot, this day and age its actually cheaper to replace the axle. So you would need to replace that side of the axle (the half shaft).

Posted on Nov 20, 2008

  • 507 Answers

SOURCE: average repair cost for cv joint or axle replacement

Average time should be around 2-3 hours. Every shop charges different hourly rates. Dealerships will be around at least 80 an hour, smaller shops will run lower.

Posted on Jan 05, 2009

blueextc3221
  • 15935 Answers

SOURCE: how do take out the cv joint on the front axle of

assuming you have the 2wd version....

1997-99 Models

  1. Disconnect the negative battery cable.
  2. Unlock the steering column so the linkage is free to move, then raise and support the front of the vehicle safely using jackstands.
  3. Remove the tire and wheel assembly.
  4. Insert a drift through the brake caliper into one of the brake rotor vanes to prevent the drive axle from turning.
  5. Remove the axle nut and washer from the hub end of the shaft. Hold the hub from turning and loosen the axle nut. Once the nut is loosened unthread it and remove the washer.
  6. Remove the brake caliper and support it with a piece of wire to avoid damaging the brake hose. Remove the brake rotor.
  7. Remove the ABS and brake line brackets from the top of the upper control arm.

Be careful when supporting the lower control arm that any components are damaged with the supporting device.
  1. Place a jackstand or jack under the lower control arm.
  2. Separate the axle shaft from the hub by placing a block of wood against the outer edge of the axle (to protect the threads), then strike the block of wood sharply with a hammer. Do not remove the axle at this time.
  3. Remove the cotter pin and retainer, then loosen and remove the upper ball joint stud nut away from the knuckle. Tip the knuckle out and toward the rear of the vehicle. Suspend the knuckle from the upper control arm or frame in order to prevent straining and damaging the brake line.
  4. Remove the lower shock absorber retainers, then compress the shock and secure it out of the way using safety wire.

Once the lower ball joint is separated from the knuckle, simultaneously push the axle shaft in towards the differential to allow room for the knuckle and assembly to be removed.
  1. Remove the cotter pin and retainer, then loosen and remove the lower ball joint stud nut away from the knuckle.
  2. Lower the safety stand or jack at the lower control arm to relieve pressure on the torsion bar, then separate the axle from the knuckle.
  3. Remove the differential carrier shield, being very careful not to damage the axle seal.
  4. To remove the shaft from the differential carrier, place a block of wood or a brass drift against the tripot housing, then strike it outwards using a hammer. You will have to hit it hard enough to overcome the snapring pressure retaining it.
  5. Support the drive axle, then pull the axle straight out from the carrier being careful not to tear the boot.

Posted on Apr 06, 2009

  • 416 Answers

SOURCE: when replacing a outer C.V joint boot , do you

you can replace just the outter but you may want to replace the whole axle alot easier

Posted on Jan 17, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove the cv joint boot on hyundai accent


If you clean away the grease inside the boot and look where the axle goes into the joint there is a snap ring there. Spread the snap ring and pull the joint off the axle.

Oct 02, 2012 | Cars & Trucks

1 Answer

How long to replace CV joint outer boot 2001 Sonata V6 please?


The CV-boot has C-clips inside the boot they must be released befor the boot will come apart. It would be very hard to tell you how to do it on this page. I would not recommend doing this if you do not know what you are doing, as this requires dissassembly of the front brake and suspension system. You really need a repair manual on how to fix CV-joints. raise the front end and support with stands, remove wheel, remove axle nut, remove bolt that attaches bottome of strut to control arm remove lower ball joint bolt smack the knuckle where the ball joint is to remove and flip the knuckle out of the way, use pry bar to pop halfshaft out of ******. while installing new one make sure the splines line up and it pops in place installation reverse of removal

Aug 07, 2012 | 2001 Hyundai Sonata

1 Answer

How to replace the front outer boot


The outer CV-joint boot can be serviced or replaced by removing the inner CV-joint. Click this link below for replacing instructions:--- http://repairhelpcenter.blogspot.com/2011/10/how-to-replace-front-drive-axle-cv.html ----------- This will help.Thanks.Helpmech.

Oct 17, 2011 | 2003 Chevrolet Tracker

2 Answers

Cv joint but the plastic thang that go around it


One would have to remove the half shaft to service the cv joint properly.

CV-Joints Overhaul Check the CV-boot for wear tccs7030.jpg

Removing the outer band from the CV-boot tccs7031.jpg

Removing the inner band from the CV-boot tccs7032.jpg

Removing the CV-boot from the joint housing tccs7033.jpg

Clean the CV-joint housing prior to removing boot tccs7034.jpg

Removing the CV-joint housing assembly tccs7035.jpg

Removing the CV-joint tccs7036.jpg

Inspecting the CV-joint housing tccs7037.jpg

Removing the CV-joint outer snapring tccs7038.jpg

Checking the CV-joint snapring for wear tccs7039.jpg

CV-joint snapring (typical) tccs7040.jpg

Removing the CV-joint assembly tccs7041.jpg

Removing the CV-joint inner snapring tccs7042.jpg

Installing the CV-joint assembly (typical) tccs7043.jpg

prev.gif next.gif

Oct 08, 2010 | 2004 Oldsmobile Alero

1 Answer

1997 Pathfinder How do you replace the left outer cv boot?


How to Replace a CV Boot
( DIY Complexity: Hard / Time: 3.2 hours )

Parts:
1. CV Boot
2. CV Boot Clamp Kit

Tools:
1. Mallet Hammer
2. 3/8 in. Drive Ratchet
3. Combination Wrench Set
4. Floor Jack
5. Flashlight
6. Flat Head Screwdriver
7. Socket Set
8. Tire Iron

Steps:
Step 1 Secure the vehicle on a level surface, making sure the vehicle will not roll or lean too much when jacked up.
o Tip: Safety Tip:Always wear safety glasses when working on your vehicle. Wear other personal protective equipment (PPE) when necessary, for example latex gloves or safety shoes.

Step 2 Lift up the front of the vehicle using a jack.
o Tip: Using an aftermarket floor jack, instead of the original equipment (OE) jack, can make the job easier and safer. Verify the condition of the floor jack before use.

Step 3 Secure the vehicle with jack stands on both sides for safety before starting any work. The pinch welds and the frame are the two best locations. Do not rely on the jack to hold the vehicle up while working.
o Tip: Try to find a flat, level, and strong surface to put the jack stands.

Step 4 Find the correct size socket and large ratchet or tire iron and turn the wheel lug nuts counter clockwise. Remove the front wheels.
o Tip: It is a good idea to try and break the lug nuts free before you jack the wheels off the ground. This way they you will not spin the front wheels or put stress on the transaxle.
o Tip: Lug nuts fasten the wheel to the hub and may be on very tight. To gain more leverage, use a breaker bar to loosen the nuts.

Step 5 Inspect the CV boot for damage.
o Tip: The CV joint may be worn if the boot is damaged. Thoroughly inspect the CV joint assembly before installing the new boot. If the CV joint is damaged, replace the entire CV joint axle assembly.

Step 6 Mark the axle for installation reference. Remove the CV joint axle assembly.

Step 7 Using a bench vise, hold the shaft of the CV joint secure so that you can separate the CV joint from the shaft. Remove the CV boot clamps.

Step 8 Slide the CV boot off the outer CV joint.

Step 9 Using a rubber mallet, knock the CV joint off of the axle shaft.

Step 10 Remove the old boot from the CV axle shaft and wipe off any old grease. Clean the sealing surface on the CV joint.

Step 11 Fill the CV joint with grease and get it ready to slide back onto the shaft.

Step 12 Slide the new boot onto the shaft but do not tighten the inner clamp yet. Install a new retaining clip before putting the joint and axle together.

Step 13 Slide the CV joint back onto the axle shaft completely.

Step 14 Pack the boot with grease and slide the boot over the CV joint housing. Secure the boot with new clamps.

Step 15 Install the CV joint and axle back into the vehicle in the reverse order that it was removed.

Step 16 Mount the wheel back onto the hub assembly.

Step 17 Tighten lug nuts in a star pattern and torque to suggested manufacturer specifications in the vehicle owner’s manual.

Step 18 Remove jack stands.

Step 19 Lower vehicle with jack until it is securely on the ground.

Step 20 Drive the vehicle to make sure that any noises are no longer present and that there are no indications of wearing parts. Before road testing, visually inspect the area you have worked on to make sure everything is tightened and assembled properly.

Hope help with this (remember rated and comment this help).

Mar 12, 2010 | 1997 Nissan Pathfinder

3 Answers

Clicking noise in the front wheels when I turn corners


you have an axle constant volicity joint going out. Well need to be replaces.

Nov 24, 2009 | 2001 Hyundai Accent

1 Answer

When turning, a knocking sound is heard in engine


Check the boots on your CV axles. If the boot is torn the axle will need to be replaced.

Sep 04, 2009 | 2006 Hyundai Tucson

1 Answer

Hyundai 2005 Elantra cv boot replacement instructions.


There are no instructions available except with the purchase of SOME boot kits. Depending on the CV joint design, you may not be able to remove the joint from the axle. However, most Hyundai CV joints can be removed from the axle by using a drift and a 2 pound hammer to knock the joint off the axle. Once you've done this, it's a simple matter of removing the old boot and installing the new one w/fresh grease and tension bands. Otherwise, you have to remove the DOJ from the other end of the axle and replace the boot that way.

Aug 24, 2009 | 2005 Hyundai Elantra

1 Answer

Cv joint removal


Get the replacement cv axle and remove inner boot and clip and bearings. Do the same on the old axle. Replace bearing clip, cv shaft and reassemble. Do not try to remove the part from inside the front axle unless you want to spend about six hours of time and money.

May 12, 2009 | 1999 Isuzu Rodeo

1 Answer

Hyundai Tucson 2.0L Year 2006


Get the mechanic to check the front CV boots for tears and get them to check the front CV joints. Explain the problem to the service manager. They should know how to properly check them. The shafts usually come as a rebuilt assembly with new joints on both ends, and are relatively easy to replace.

Aug 26, 2008 | 2006 Hyundai Tucson

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...