Question about Chevrolet Cars & Trucks

1 Answer

Remove glove box 2002 blazer

Blower motor won't turn off. blower is behind the glove box, i think

Posted by on

  • Johnny Horner Feb 13, 2014

    Thank you all for your suggestions. Looks like I can handle this repair myself.

    Thanks again!

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Chevrolet Expert
  • 97 Answers

Have a look at the blower resistor pack

Posted on Feb 13, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 94 Answers

SOURCE: A/C BLOWER

most likely its the blower motor resister and is located behind the glove box. there are a few philips head screws you will need to remove inside the glove box and under the glove box to get the glove box out after that it should be a walk in the park

Posted on Mar 09, 2009

  • 7 Answers

SOURCE: how to replace blower motor resistor on 2000 grand caravan

there will be two 8mm screws holdin it in.. with two connectors into it

Posted on Jan 05, 2009

emissionwiz
  • 74945 Answers

SOURCE: Blower motor location for 2000 Caravan

The motor is located just under the glove box on the passenger side. I remove the glove box then the panel below the glove box. I also go ahead and pull back the carpet and the padding under the motor. It is held in place by 3-4 bolts that take a 7-8 millimeter socket. I use a swivel extension for the back bolts. The motor with the fan blade attached is a tight fit, just keep wiggling and pulling it should come out. Try to remove the old moter without cracking the fan blade, because sometimes the replacement motor doesn't come with a blade

Posted on Sep 17, 2008

cadman000
  • 607 Answers

SOURCE: 1992 Cadillac Coupe Deville blower fan runs all the time

The BLOWER MODULE is located on the A/C EVAPORATOR housing located UNDER THE HOOD passenger side firewall. Has 2 electrical connectors. Mounted with 4 screw bolts.Hope this helps

Posted on May 21, 2009

theroadis
  • 81 Answers

SOURCE: Changing Blower motor on Chevy '98 4x4

It's simple!...Open glove box door...youll see a plastic shell that is the glove box rear portion. You should find 4, 9/32nds or 7mm (same thing just SAE or Metric) screw heads. Undo four screws and with a flat blade screw driver, gently pry out on shell at either side to clear the door straps. Once clear, just work out of resting place, set aside. You will now see like 5 relays mounted on top of the air handler. Remove bracket that holds four of them + one that is mounted alone. Pull out of the way. Checking both inside and outside, remove all screws, bolts, nuts as it were, until it is obvious there are none left. Now, this is assuming this is where your problem lies! If you are simply having a blower problem, it might be the blower module mounted right beneath and just behind relays on top of air handling box. Just take your time so you dont break anything. Good luck...theroad......

Posted on Jun 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The a/c is not blowing out any air at all. it was working great when we stopped & turned off the ignition. when we started it up it will not do a thing . defrost, or heat won't work either.


That sounds like a bad blower motor to me. Try this: Remove the lower panel from under the right side of the dash. Turn your blower motor on HIGH. Look up under the dash behind the glove box and find your blower motor housing. Take your fist and "thump" on the blower motor housing. If the blower starts blowing, replace your blower motor.

Aug 28, 2011 | 2005 Chevrolet Trailblazer Ext

1 Answer

I have had my blower motor replaced and now my blower on works on number 3? this is on a 2001 Chev Blazer


Heater blower motor resistor. This is attatched to the side of the motor housing. (Behind the glove box) This is repalceable, and when they fail, usually you only get the high speed.

Jan 08, 2011 | 2000 Chevrolet Blazer

1 Answer

The fan on my dashboard is not working. I am thinking of replacing it with a used one from a junk yard except I dont know where is located.


it's behind the glove box. here are procedures from autozone.com:

CAUTION The Supplemental Inflatable Restraint (SIR) system must be disarmed before removing the blower motor assembly. Failure to do so may cause accidental deployment of the air bag, resulting in unnecessary SIR system repairs and/or personal injury.
  • Disconnect and isolate the negative battery cable, then wait 2 minutes before proceeding with the removal. This will effectively disable the air bag system preventing possible personal injury.
Remove the glove box from the instrument panel.


17baf45.gif


Fig. The blower motor is located behind the glovebox, behind the blower motor cover


  • Remove the A/C-heater blower motor cover.
  • Disconnect the blower motor wiring connector.
  • Remove the blower motor wiring grommet and feed the wiring through the blower motor housing.
Remove the blower motor mounting screws.


41198be.gif


Fig. Once the cover is removed, unplug the electrical connector and push it through the opening in the housing


803e435.gif

Fig. The blower motor is secured to the housing with three small screws


Allow the blower motor assembly to drop downward to clear the instrument panel and remove from vehicle.


To install:

  1. Place the blower motor assembly into position on the A/C-heater unit and tighten the mounting screws.
  2. Route the blower motor wiring through the blower motor housing and seat the wiring grommet in the hole of the blower motor housing.
  3. Reconnect the blower motor electrical connector.
  4. Install the A/C-heater blower motor cover.
  5. Install the glove box into the instrument panel.
  6. Reconnect the negative battery cable. Check blower motor operation.

Oct 15, 2010 | 2003 Dodge Caravan

1 Answer

Remove dash to get to sensore for blower on 2002 dodge ram 1500 the blower only works on high


If the blower motor is only running on high the problem is the blower motor resistor. location for resistor is behind the glove box. Remove all items in glove box. remove glove box from dash and to the left of the blower motor you will see a electrical plug, remove the plug and the resistor mounting bolts. remove the resistor and replace it with new resistor. reinstall all items as you have taken them off. hope this will help you.

May 12, 2010 | 2004 Dodge Ram 1500

2 Answers

How to replace a heat/ac blower motor in a 2001 blazer


it is under dash ,behind glove box,not a hard job at all

Dec 24, 2009 | 2001 Chevrolet Blazer

1 Answer

Replace blower motor 1998 plymouth voyager


it is located behind and below the glove box,you might want to remove the glove box assembly to see it easier,
there are four screws holding a blower motor cover you to take off first,now remove the screws holding the blower motor up,disconnect the motor wires.
if your changing this because you think its bad,you should test the blower motor wires with a test light with the key on and blower switch turned on.if you have power in the wires,then it is bad.
but if you have no power in wires it could be blower motor resister,or switch.

Nov 28, 2009 | 1998 Plymouth Voyager

1 Answer

2006 grand cherokee laredo heater fan only works on high, I had the same problem with my sebring sedan and had to replace heater fan motor. Is this likely the same problem? Where is it located?


It is NOT the motor itself in this case, it is the blower motor's resistor pack, which was and seems still is a common problem with the grand cherokees. It is usually located under or behind the glove box right on the firewall, and some rarer cases under the hood, also on the firewall but on the hood side and not the inside of the vehicule, next to the blower motor assembly. In your case it should be located inside the vehicule and requires removal of the glove box according to a few tech experts on the web. Here is the section of tech info i have found which i think will be the most useful for you:

"Get to the blower motor in a Grand Cherokeemag-glass_10x10.gif by first disabling the airbags. Unscrew the glove box and remove it. Unscrew and remove the blower motor wire harness found directly behind the blower motor. Unscrew three screws holding the blower motor into place and then remove the motor."

So I hope this helps you out.

Jul 13, 2009 | 2006 Jeep Grand Cherokee

1 Answer

2002 Trailblazer blower not working


The blower motor resistor card is located under the glove box. You have to take the bottom panel from underneath the glove box out(be careful not to break the wire clip that holds the wires in place on that panel). Once you take the panel loose look in the back. You will see the blower motor. Behind the blower motor is the card. You will need a 9/32 for the panel and a 7/32 for the card. It is only 4 screws total to remove and 2 wire harness clips. It is about a 15 minute job. Good luck and hope this helps.  Auto Zone has the part for around $15.00 and will have the step by step instrutions for you also if you need it free of charge. I think the dealer charges $109.00 for this repair. 

Jun 17, 2009 | 2002 Chevrolet TrailBlazer

3 Answers

A/C BLOWER


most likely its the blower motor resister and is located behind the glove box. there are a few philips head screws you will need to remove inside the glove box and under the glove box to get the glove box out after that it should be a walk in the park

Mar 09, 2009 | 1998 Lexus Gs 400

3 Answers

Inside fan has just stopped working


It could mean a new fan,but most systemes use a blower motor resistor to control the speeds of the fan which could have died and is lockated in the air box for climait control.

Aug 17, 2008 | 2004 Saab 9-3

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...