Question about 1986 Mitsubishi Lancer 1.8

1 Answer

Pls give me correct tappet valve clearance of intake and exhaust for 4G15 mitsubishi lancer

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mitsubishi Master
  • 956 Answers

Valve clearance Intake 0.20 mm (Hot- at operating temp)
Valve clearance Exhaust 0.25 mm (Hot).

Posted on Feb 24, 2014

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 2210 Answers

SOURCE: please give me the correct tappet clearance of intake and exhaust valve of mitsubishi 4g54 with turbocharger

My initial sweep of the web gives Inlet 0.010 thou, Exhaust 0.008 thou.
You would need to check this because industry norm is to have the greater clearance on the exhaust valve because of the increased heat expansion.

Posted on Nov 05, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hey there I need the exhaust and Intake(valve) clearance for a komatsu 300-6 please


note Perform the valve clearance check and adjustment at the engine cold state. 1.Remove all of the ignition coils. 2.Remove the cylinder head cover.
caution Turn the crankshaft always clockwise. 3.Turn the crankshaft clockwise, and align the timing mark on the exhaust camshaft sprocket against the upper face of the cylinder head as shown in Figure. Therefore, No.1 cylinder goes to the compression top dead center. 4.Using a thickness gauge, measure the valve clearance with the arrow shown in Figure. If deviated from the standard value, make note for the valve clearance.
Standard value:

    Intake valve 0.20 ± 0.03 mm (0.008 ± 0.0012 inch)
    Exhaust valve 0.30 ± 0.03 mm (0.012 ± 0.0012 inch)
5.Turn the crankshaft clockwise 360 degrees, and put the timing mark on the exhaust camshaft sprocket in position shown in Figure. Therefore, No. 4 cylinder goes to the compression top dead center. 6.Check the valve clearance with the arrow shown in Figure. In the same procedure as 4.
7.If the valve clearance is deviated from the standard value, remove the camshaft and the valve tappet. For the camshaft removal, refer to Camshaft Removal and Installation . 8.Using a micrometer, measure the thickness of the removed valve tappet. 9.Calculate the thickness of the newly installed valve tappet through the following equation.
A: thickness of newly installed valve tappet
B: thickness of removed valve tappet
C: measured valve clearance
Equation

    Intake valve: A = B + [C - 0.20 mm (0.008 inch)]
    Exhaust valve: A = B + [C - 0.30 mm (0.012 inch)] note The valve tappet ranges 3,000 - 3,690 mm (0.1181 - 0.1453 inch) and has 47 types per 0.015 mm (0.0006 inch). The thickness below a decimal point is stamped on the reverse side of the valve tappet. 10.Install the valve tappet selected through the procedure 9, and put the camshaft in position. For the camshaft installation, refer to Camshaft Removal and Installation .
    11.After installing the timing chain, measure the valve clearance using the procedure 3 to 6. Confirm the clearance is within the standard value.
    caution Completely remove all the old FIPG, which might be remaining among the components. 12.After completely removing the liquid gasket adhering on the timing chain case, cylinder block and cylinder head, degrease them with white gasoline.
    caution The cylinder head cover should be installed within 3 minutes of applying liquid gasket.
13.Apply a 4 mm bead of liquid gasket as illustrated.
Specified sealant:
    THREE BOND 1217G or equivalent
14. Install the cylinder head cover and tighten the tightening bolts using the following procedures.
(1) Temporarily tighten to the following torque in order shown in the illustration.
Tightening torque: 3.0 ± 1.0 N·m (27 ± 8 in-lb)(2) Tighten to the specified torque in order shown in the illustration.
Specified torque: 5.5 ± 0.5 N·m (49 ± 4 in-lb)15.Install the ignition coils.

Jan 23, 2017 | Cars & Trucks

1 Answer

What is the valve clearance for intake valve and exhaust valve for mitsubishi engine 4D32?


Please follow link to complete instuction's on the Correct way to set valve clearance on the 4D32 engine type.
6 INTAKE AND EXHAUST VALVE CLEARANCE INSPECT AND ADJUST

May 15, 2016 | Mitsubishi Cars & Trucks

3 Answers

I need to set my intake and exhaust valves, can u please give me the settings.(tappet clearance)


The Chilton and Haynes manuals are your best bet. Order it at your local Autozone or goto the Library and research them online fro free.

Jan 24, 2015 | 2006 Tata Indica LSi

1 Answer

Please give me the correct tappet clearance of intake and exhaust valve of mitsubishi 4g54 with turbocharger


My initial sweep of the web gives Inlet 0.010 thou, Exhaust 0.008 thou.
You would need to check this because industry norm is to have the greater clearance on the exhaust valve because of the increased heat expansion.

Nov 05, 2013 | 1992 Mitsubishi Pajero

1 Answer

Valve Clearances inlet and exhaust


j24b engine D.O.H.C.
U.S.A?
open hood , look up. see white sticker, see clearances.?
off online F.S.M
Valve clearance specification when cold :
59 to 77deg F or 15 to 25deg C (engine temps)
Intake: 0.0063 to 0.0094 inch (0.16 to 0.24mm)
Exhaust: 0.0123to 0.0153 inch (0.31to 0.39mm)
you must remove the bucket,tappet , to change lash.
MIKE IT (that means a micrometer)
then buy shims or new buckets to fit. (generic answer)
the book says buy correct tappet after measuring, yours.
and it's out of range, and doing the math first.

that is it.

May 05, 2013 | 2010 Suzuki Kizashi

2 Answers

Procedure of tappet adjustment


make sure engine is warmed up. Put cylinder one at top dead center,remove the valve cover,loosen all adjustment lock nuts,adust intake and exhaust valves on cyl #1 and intake valve on #2 and exhaust valve on #3. now rotate crankshaft 360 degrees clockwise, now adjust intake valves on cyl#3 and cyl #4 and exhaust valves on cyl #2 and cyl #4.now tighten lock nuts and install valve cover. specs are intake valves 25mm clearance and exhaust 28mm clearance, use a feeler gauge,heres a picture to show you where to check clearance.7675a52.gif

Mar 14, 2010 | 1986 Suzuki Samurai

1 Answer

WHAT IS THE TAPPET CLEARANCE FOR NISSAN GA 15 CARBURATED,INTAKE AND EXHAUST?


what is the tappet clearance setting for the ga15 nissan sunny
i need help to know the clearance of intake and the exhaust valve.

Nov 02, 2009 | Nissan Sentra Cars & Trucks

1 Answer

Valve Clearance for the 4G94 engine in the 2002


intake valve is 0.0008 -0.0020 exhaust valve is 0.0020- 0.0035

Apr 25, 2009 | 2002 Mitsubishi Lancer

2 Answers

Valve clearances


On the intake 0.0008 or 0.0020 (it's in between these 2)

this is for the stem to guide clearance. (for the intake)

The Exhaust 0.0018 to 0.0030 stem to guide clearance.

Jul 10, 2008 | 1993 Nissan Pickup

Not finding what you are looking for?
1986 Mitsubishi Lancer 1.8 Logo

Related Topics:

394 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8548 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...