Question about 2008 Honda Civic

Open Question

Change alternator on hj60 landcruiser

Step by step removal,of alternator on hj60 landcruiser diesel

Posted by Anonymous on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ajkill
  • 2035 Answers

SOURCE: Alternater replacement

TO remove :

  1. With the ignition OFF, disconnect the negative battery cable.
  2. Remove the power steering pump. Refer to for the complete procedure.
  3. Remove the cruise control actuator but do not disconnect the actuator cable; simply move the unit out of the way with the cable attached.
  4. Unplug the multi-pin electrical connector.
  5. Remove the terminal nut and remove the wire from the terminal.
  6. Loosen the adjusting bolt; remove the alternator nut.
  7. Remove the belt from the alternator pulley.
  8. Remove the adjusting bolt, the lower through-bolt and the small support stay.
  9. Support the alternator. Remove the upper through-bolt and remove the alternator.
  10. If desired, remove the alternator mounting brackets.
  11. If the alternator brackets were removed, reinstall them. Coat the bolts with a thread sealer or liquid thread lock. Install the bracket bolts and tighten them to 36 ft. lbs. (50 Nm).
  12. Fit the alternator into place. Install the upper through-bolt and tighten it to 33 ft. lbs. (45 Nm).
  13. Install the small stay, the lower through-bolt and the adjusting bolt. Make certain the adjusting bolt is properly installed.
  14. Install the belt. Install the alternator nut. Adjust the belt tension. Tighten the alternator nut to 19 ft. lbs. (26 Nm).
  15. Connect the wire to the terminal and tighten the nut.
  16. Engage the multi-pin connector to the alternator.
  17. Install the cruise control actuator.
  18. Install the power steering pump.
  19. Connect the negative battery cable.15463b8.jpg

Posted on Oct 14, 2008

SOURCE: how to change an alternator in 1983 honda accord

If your radio is coded, make sure you have the code and know how to re-enter the code in the radio.

  • Remove both battery cables and secure them away from the battery terminals.
  • Detach the E, F and N plug from the the alternator.
  • Slacken the alternator mounting bolts and move the alternator forward towards the engine.
  • Remove the drive belt.
  • Now undo all the mounting bolts and lift the alternator clear of the vehicle.
Re-fitting is just the reversal of the removal.

Posted on Dec 01, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How many stages and what neuton meters are there for tightening head bolts?


Read this:

http://www.scribd.com/doc/52122956/Toyota-Landcruiser-Engine-Manual-2H-12HT

Aug 02, 2014 | Toyota LandCruiser Cars & Trucks

2 Answers

How to change alternator on peugeot 1.4 16v


For step by step alternator removal on Peugeot vehicle,click the link below:----

How to change Alternator on Peugeot

http://www.howtorepairguide.com/2012/11/how-to-change-alternator-on-peugeot.html

----------

These will help.

Thanks.

Nov 28, 2012 | Cars & Trucks

1 Answer

Remove an alternator 2003 caravan


Hello,

The removal of the alternator of your car is not a tsking job,simply follow the instructions described below;

STEP 1
Disconnect battery negative cable.
STEP 2. Disconnect the push-in field wire connector from back of alternator.

STEP 3 Remove the nut holding the B+ wire terminal to the back of alternator.

STEP 4. Separate B+ terminal from alternator.

STEP 5.
Raise the vehicle and support.

STEP 6.
Remove the right front lower splash shield.

STEP 7. Remove accessory drive belt.

STEP 8.
Remove the lower oil dip stick tube bolt .

STEP 9. Remove wiring harness from the oil dip stick tube
STEP 10.
Remove the 3 mounting bolts and lower the vehicle.

STEP 11.
Remove oil dip stick tube,afterwards,take out the alternator from the vehicle.

Problem solved,Thank you for using fixya.

Jul 10, 2011 | 2003 Dodge Caravan

1 Answer

How do i change/replace the alternator on a 2002 GMC Envoy? A step by step would be great if someone has it.


  • Disconnect battery ground cable.
  • Remove air inlet duct.
  • Remove heater hose brace bolt from rear of alternator.
  • Disconnect alternator electrical connectors.
  • Remove accessory drive belt.
  • Remove alternator mounting bolts.

Dec 13, 2010 | GMC Envoy Cars & Trucks

1 Answer

Suzuki aerio 2002 alternator change step by step


1. Park vehicle on level ground.
2. Remove battery from vehicle.
3. Remove air cleaner outlet hose, engine under cover ( right side ) and exhaust pipe # 2 .
4. Disconnect " B " terminal wire and coupler from the Alternator ( Generator ) .
5. remove Alternator ( Generator ) belt.
6. Remove Alternator ( Generator ) cover.
7. Remove Alternator ( Generator ) bracket mounting bolts.
8. Remove Alternator ( Generator ).
Installation : Reverse dismounting procedure.
Replace Seal Ring between exhaust pipe # 1 and exhaust pipe # 2.
Torque exhaust bolts to : 43 N-m ( 4.3 kg-m,31.5 lb-ft )
Replace cable straps / defective parts as necessary.
Reinstall battery.

Aug 11, 2010 | 2002 Suzuki Aerio

3 Answers

Where is oil filter on the 200 diesel toyota


The engine has the filter on the left hand side halfway up the
block,actually sitting face down.

Oct 30, 2009 | 2009 Toyota Land Cruiser

1 Answer

35,000 miles and had to replace glow plugs


buy a toyota Ihave a 1989 hj60 landcruiser ,295000 klms and i have never had to change the glow plugs yet -----touch wood .get with the strength get a tojo

Sep 22, 2009 | 2005 Mercedes-Benz Mercedes Benz E320 Cdi

1 Answer

How to change an alternator in 1983 honda accord


If your radio is coded, make sure you have the code and know how to re-enter the code in the radio.
  • Remove both battery cables and secure them away from the battery terminals.
  • Detach the E, F and N plug from the the alternator.
  • Slacken the alternator mounting bolts and move the alternator forward towards the engine.
  • Remove the drive belt.
  • Now undo all the mounting bolts and lift the alternator clear of the vehicle.
Re-fitting is just the reversal of the removal.

Nov 23, 2008 | 1983 Honda Accord

1 Answer

I have a landcruiser 1994 gas. i one too change it for diesel


to change a gas to a diesel is a very big project. you will need all new feul system, lines, filters, pumps, etc. then the motor has to fit the trani. which is hard to find, so you might need a new trani. then braking, cooling, heating, and so much more. but if you still want to the best thing to do is get a convertion step- by- step book. if you found someone that could tell you. they would need to know what car exsactly and what motor you would be putting in to it.

Jun 13, 2008 | 1994 Toyota Land Cruiser

Not finding what you are looking for?
2008 Honda Civic Logo

Related Topics:

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...