Question about 2004 Isuzu Rodeo

Open Question

Holden rodeo 3.5 L v6 B0007 code - 2004 Isuzu Rodeo

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 3 Answers

SOURCE: 1994 isuzu holden rodeo injection timing adjustment

try u-pull our patrs

Posted on Sep 12, 2008

Ad
stevenhurc
  • 450 Answers

SOURCE: 1990 holden rodeo /isuzu pick-up temp sender

from memory it is in inlet manifold some were in front middle section bottom, (underneath) 4ZE1?
single wire possibly yellow

Posted on Jun 25, 2009

jimboz4
  • 305 Answers

SOURCE: holden rodeo v6 1998 3.2L 4wd

the click is the solenoid hitting the bendix, try geting someone to turn the key,and as they do,tap the starter with a hammer, or heavy wrench, if it starts, then its the solenoid, and it can be stripped and replaced, if it doesnt start,then its the bendix, and you will need to replace the starter, ....which you can do yourself, .....takes about an hour or so

Posted on Jul 22, 2009

stevenhurc
  • 450 Answers

SOURCE: torque settings for a holden rodeo 3.5 ra. Head

stage 1 = 29Nm(21 lb ft/3.0 kg-m)
final = 64Nm(47 lb ft/6.5kg-m)
do not reuse head bolts or apply any lubricant to the bolts. Do up bolts in following order for each head.
6 1 3 7
front
5 2 4 8

Posted on Dec 05, 2009

stevenhurc
  • 450 Answers

SOURCE: NEW CLUTCH SLIPPING ON 2004 V6 HOLDEN RODEO

did you bleed the hydralic clutch system on this vehicle? = air in system or not bleed properly.
most of the flywheels for this model were not to be machined...... however it is ok to machine these only slightly but you must machine the surface the clutch plate contacts with the same amount as the outer raised section the pressure plate bolts to.
new flywheels have painted stamped writing saying do not machine...so if hydralic system is ok find out about flywheel.
also may pay to check clamping force of pressure plate most clutch places can do this or some workshops that is if fingers on pressure plate are all at the same height, not broken or cracked..

Posted on Dec 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Just replaced the ecm in my 3.5l v6 coded it all in and the code b0007 keeps coming up and car wont start


B codes are for the body control module(BCM). Sounds like you may have replaced the wrong module.

May 22, 2015 | Cars & Trucks

1 Answer

I have a 2006 holden rodeo dual cab, 3.6L v6 with tail lights playing up.. On closer inspection I cannot see any chassis earthing/grounding leads present. Is this correct on these?


Check the bulb housing and reflectors . It the housing is plastic with a metal bulb housing moulded in then there should be a black wire attached to the bulb housing. I suspect that it will be all plastic so you will have a return earth wire.

Sep 22, 2013 | 2005 Holden Rodeo

1 Answer

Holden Rodeo RA Workshop Manual


We are a USA site and we do not have this make in the US. Sorry.

Mar 02, 2012 | Cars & Trucks

1 Answer

Holden rodeo 3lt turbo diesel Fault code P0087 fuel rail pressure to low was the best way to correct the problem


2004 holden rodeo 3L ITD. dt P1120. Saying tps fault. Used scan tool to inspect data list an ECU is recieving signal perfect. Goes from 16% to 100%. Double checked TPS output from TPS plug and goes from 0.6v to 4v nice an smoothly. Im suspect on ECU because when i erased code and started engine it revved up to red line by itself but only did once. Any help would be great....

Jan 23, 2012 | 2005 Holden Rodeo

1 Answer

Need a diagram for a holden rodeo v6 fan belt


i need a diagram on how fan belt goes on a holden rodeo 2004 v6

Oct 20, 2010 | Isuzu Rodeo Cars & Trucks

1 Answer

NEW CLUTCH SLIPPING ON 2004 V6 HOLDEN RODEO


did you bleed the hydralic clutch system on this vehicle? = air in system or not bleed properly.
most of the flywheels for this model were not to be machined...... however it is ok to machine these only slightly but you must machine the surface the clutch plate contacts with the same amount as the outer raised section the pressure plate bolts to.
new flywheels have painted stamped writing saying do not machine...so if hydralic system is ok find out about flywheel.
also may pay to check clamping force of pressure plate most clutch places can do this or some workshops that is if fingers on pressure plate are all at the same height, not broken or cracked..

Dec 01, 2009 | 2004 Isuzu Rodeo

1 Answer

Holden rodeo v6 1998 3.2L 4wd


the click is the solenoid hitting the bendix, try geting someone to turn the key,and as they do,tap the starter with a hammer, or heavy wrench, if it starts, then its the solenoid, and it can be stripped and replaced, if it doesnt start,then its the bendix, and you will need to replace the starter, ....which you can do yourself, .....takes about an hour or so

Jul 22, 2009 | 1998 Isuzu Rodeo

Not finding what you are looking for?
2004 Isuzu Rodeo Logo

Related Topics:

344 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14384 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...