Question about GMC Acadia

Open Question

Replacing a Turn Signal Switch in gmc - Acadia GMC Cars & Trucks

Posted by Anonymous on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 32 Answers

SOURCE: Turn signal switch

You will need to remove the steering column to start.From there there should be a either small bolts on the switch itself. After that just remove the plug from the harness from under the dash and pull the whole assembly out.

Posted on Dec 24, 2008

Ad
  • 11 Answers

SOURCE: 1994 gmc mini van turn signal broken need help on how to replace

If the switch is broken, you need to remove: driver side knee bolster, snack tray/drink holder and dash rim. Remove the lower steering column cover (2 screws).You will need a E5 torx socket to loosen the upper cover. Alldata recommends removing the lock cylinder to access the 2 torx screws holding the switch in place, but I did it without (disabled the air bags and removed the driver side, accessing one screw through the steering wheel, top screw with bit and ratchet wrench). The wiring harness connectors attach to the main block under the steering wheel. Auto Zone has a replacement switch assembly for about $180, dealer price $417. E-mail me if you need further instructions...

Posted on Jun 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

1967 GMC 2500 brake lights flash on and off except when blinkers are turned on. How do I fix it ?


Sounds like you need a new turn signal switch. And a new flasher relay, just in case your old one got overused! Those little flasher relay cylinders were real cheap back in the day, about $2. It's under the dash around the steering column, probably in a little metal clip (yea, real metal). Don't confuse it with the hazards flasher, both look the same. You can hear and feel the turn blinker flasher when it is doing its thing, and same with the hazards flasher, if you want to check. The clicking is the make and break contact of the circuit to cause a blinking bulb.

The reason I say you need a new turn signal switch is because the brake light signal wire is routed through the turn signal switch before it goes to the rear brake light bulbs. It is inside the turn signal switch that the brakes and rear turn signal lights are made to share the same filaments inside the bulbs. The brake lights don't pass through the flasher, but somehow your turn switch is sending power to the flasher. If the wiring under your dash has not been radically altered, really messed up, then your turn signal switch has got infected with a malware virus: it is worn out and needs replacing. Good luck with that old piece of iron, Greg.

Apr 09, 2015 | GMC Cars & Trucks

1 Answer

How do i get to my hazard switch in my 02 gmc envoy ..a vid would be really hepfull


Are you sure that is what you need to replace ? Do the turn signals work ? May be the turn signal hazard flasher module is bad ! How To Install Turn Signal Wiper Cruise Control Switch 2002 09 GMC Envoy...

Mar 23, 2015 | 2002 GMC Envoy

1 Answer

Where is the brake relay on a 2001 gmc sierra.


Try wiggling the hazard light switch while pressing on the brakes.The taillights are connected to the turn signal switch before it goes to the brake switch.The contacts on the hazard switch are probably dirty(I remember this problem years ago,same symptoms-3rd light works but l/R tailights not working).You may just be able to turn the hazards on+off a bunch of times to clean the contacts instead of replacing the switch.

Jun 13, 2012 | 2001 GMC Sierra 1500HD

2 Answers

No turn signals


Try replacing your turn signal flasher relay, very cheap part (around $2) and can be bought from just about anywhere that sells any type of auto parts. Also check your fuses.

If replacing the relay doesn't remedy your problem, take a voltmeter and test the socket the relay plugs into. Make sure to turn your turn signals on before this test or else it will read 0 on the voltage meter. If you are getting no power there, you are going to have to dig further into your dash and trace the wires to your turn signal switch. If you have to go this far, also check for voltage at the turn signal switch/lever (on your steering column).

Hope this helps guide to to your problem.

Feb 26, 2010 | 1996 GMC Jimmy

4 Answers

1997 gmc 3500, no brake lights, already changed the brake light switch. still have same problem. i have running lights and turn signals, and flashers. can anyone help me fix this?


Hello , do you have amber colored turn lenses or red? I ask this because maybe the bulbs are not dual filament type in the brake light socket. There maybe a brake light fuse also. Do you have a third brake light as well? Does it work? Quinn , Arizona

Jul 25, 2009 | 2000 GMC Savana

1 Answer

No brake/hazard lights,have running/turn signal lights


Suggest you change hazard flasher 'can' first, then go to the hazard switch. I'm betting it's the flasher can.

May 11, 2009 | GMC Sierra 2500 Cars & Trucks

1 Answer

1994 gmc mini van turn signal broken need help on how to replace


If the switch is broken, you need to remove: driver side knee bolster, snack tray/drink holder and dash rim. Remove the lower steering column cover (2 screws).You will need a E5 torx socket to loosen the upper cover. Alldata recommends removing the lock cylinder to access the 2 torx screws holding the switch in place, but I did it without (disabled the air bags and removed the driver side, accessing one screw through the steering wheel, top screw with bit and ratchet wrench). The wiring harness connectors attach to the main block under the steering wheel. Auto Zone has a replacement switch assembly for about $180, dealer price $417. E-mail me if you need further instructions...

Apr 18, 2009 | 1994 GMC Safari

1 Answer

2000 GMC Jimmy, Flasher clicks alot even after repalcing flasher


Auto headlights do go off when turn signal is put on. The wiper problem could very well be in the blinker switch in the column, they are know to go out on these trucks. Run some tests before replacing.

Feb 24, 2009 | 2000 GMC Jimmy

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...