Question about 2006 Chevrolet Colorado

Open Question

How to change the oxygen sensor on 06 chevy colorado

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 91 Answers

SOURCE: I am having problems with the oxygen sensor on my

your o2 sensor is located on your exaust. You have either two or four, I think their is only two on a 99 chevy if I remember correctly, pre catalyst and post catalyst. This means one before your catalytic converter and one after. The pre is usualy the culprit but they will not stop your truck from cranking over. This sounds more like a battery,battery cable, or starter problem. Hope this helps, Clay

Posted on Mar 26, 2009

Ad
c17hydro
  • 2984 Answers

SOURCE: how do i change out the knock sensor on a 2006 chevy colorado

You didn't list your engine size so please pick the applicable to your motor size:

Removal & Installation 2.8L & 2.9L Engines To Remove:

  1. Lift the vehicle high enough to gain access to the knock sensor (KS) through the left front wheelhouse.
  2. Remove the left front wheel and wheelhouse liner.
Knock sensor (KS) (A), Engine harness (B), Knock sensor (KS) connector (C)


e44e83f.gif
  1. Disconnect the knock sensor (KS) connector.
  2. Detach the knock sensor (KS) from the engine block.
To Install:
  1. Attach the knock sensor (KS) to the engine block.
    • Tighten the bolt to 18 ft lbs (25 Nm).
  2. Connect the knock sensor (KS) connector.
  3. Install the left front wheelhouse liner and wheel.
  4. Fully lower the vehicle.

Posted on Sep 03, 2009

  • 75 Answers

SOURCE: need to find and replace oxygen sensor for 2003 chevy ventue

Need a 7/8 open end wrench or a o2 sensor socket. Located in exhaust pipe. The one closest to the engine is Bank 1 Sensor 1. The ones located downstream and known as "Sensor 2"

Posted on Jan 06, 2010

  • 72 Answers

SOURCE: how do you change an oxygen sensor on 2006 chevy aveo

There is a special socket for O2 sensors which allow the wires to stick out and not get twisted up. It's not expensive and available at most auto parts stores. Disconnect the sensor from the wiring harness, with the plug and then use the socket to remove and replace the new sensor. Re-connect electrical plug.

Please rate this answer. Thank you.

Posted on Apr 08, 2010

  • 1608 Answers

SOURCE: chevy colorado fault light reset

The only way to clear the check engine light is with a scan tool.Disconnecting battery will not clear codes.Hope this helps.Good luck.

Posted on Apr 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 06 Chevy Colorado and the code it gave me P0171 I don't know what side is bank one and also gave me P0305


More than likely, even if you replace the O2 Sensor, it is the hose that connects the valve covers to the EGR system. Check to see if that wiggled out or is in a position where it might have started to leak.

On the P0305, it indicates that you have a misfire, and this can be caused because of the leaking hose from the previous.

Other causes can be:

Faulty spark plug or wire
Faulty coil (pack)
Faulty oxygen sensor(s)
Faulty fuel injector
Burned exhaust valve
Faulty catalytic converter(s)
Running out of fuel
Poor compression
Defective computer

Sep 06, 2016 | 2006 Chevrolet Colorado

1 Answer

2006 Chevy Colorado 2.8 4 cyl. Engine is surging under normal acceleration. It has about 85K.


Clean the MAF sensor and the throttle body. Plus the Idle air control motor. Use a toothbrush with brake clean. Just spray the MAF with brake clean both ways..

Oct 04, 2014 | 2006 Chevrolet Colorado

1 Answer

How to change upstream o2 sensor on 2008 chevy uplander 3.9l ?


  • 1 Warm up the engine for about four minutes to bring it to operating temperature. Then turn off the engine. This will avoid damage to the exhaust pipe threads if that sensor has seized to the pipe.
  • 2 Find the oxygen sensor or sensors you need to replace. The upstream sensor is located near the exhaust manifold and the downstream sensor on the back exhaust pipe, close to the catalytic converter.
  • 3 Disconnect the oxygen sensor electrical connector. Depending on your particular Chevy model, both sensors may be disconnected from the engine compartment.
  • 4 Lift the front of your Chevy model to reach the sensor you need to change, if necessary. Use a floor jack and two jack stands to support it.
  • 5 Remove the oxygen sensor using a box-end wrench or a ratchet and oxygen-sensor socket.


  • Read more : http://www.ehow.com/how_5159092_replace-oxygen-sensor-chevy.html

    Jul 23, 2014 | Chevrolet Chevy Cars & Trucks

    1 Answer

    Engine light code p1133 on a 2005 chevy colorado


    P1133 CHEVROLET - HO2S Insufficient Switching Bank 1 Sensor 1xicon.jpghttp://engine-codes.com/p1133_chevrolet.htmlForum CodePossible causes- Heated Oxygen Sensor (HO2S) Bank 1 Sensor 1 shorted to Engine Control Module (ECM) ground
    - Heated Oxygen Sensor (HO2S) Bank 1 Sensor 1
    - Vacuum leak
    - Faulty Heated Oxygen Sensor (HO2S) Bank 1 Sensor 1 connector and wires

    Jun 24, 2012 | Chevrolet Colorado Cars & Trucks

    1 Answer

    HOW DO YOU FIX A 06 COLORADO WITH A TROUBLE CODE OF P1134


    Its an oxygen sensor bank 1 sensor 1 What the code is saying is the tranition rate of the sensor -time raito is off witch likely means the sensor is NG ITS THE CLOEST SENSOR to the front of the vehicle and its in the y pipe on the drivers side

    Nov 19, 2010 | Chevrolet Colorado Cars & Trucks

    1 Answer

    I have a 06 chevy colorado engine light came on


    hi this could be a lot of things, the only way to find out is to have it checked with a code reader, it could be something simple like a miss fire as sometimes happens or could be something more serious best get it checked out, you could have a sensor gone u/s and you might be using allot of fuel.....hope this helps

    May 10, 2010 | 2006 Chevrolet Colorado

    2 Answers

    Rough idle


    I had the same exact problem on my 2004 Colorado (3.5L). Cleaned the MAF sensor (with MAF sensor cleaner) and throttle body/plate - cleared it right up.

    May 10, 2009 | 2006 Chevrolet Colorado

    Not finding what you are looking for?
    2006 Chevrolet Colorado Logo

    Related Topics:

    43 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chevrolet Experts

    yadayada
    yadayada

    Level 3 Expert

    76846 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22246 Answers

    Ronny Bennett Sr.
    Ronny Bennett Sr.

    Level 3 Expert

    6918 Answers

    Are you a Chevrolet Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...