Question about 2006 Pontiac Montana SV6

Open Question

How can i program new keyless remote for pontiac montana sv6 2007

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 373 Answers

SOURCE: Programming a 2006 Pontiac Gran Prix Keyless remote

The rke on 06 pontiac only can be programed using a diagnostic scan tool or Tech 2.
Conect the scan tool to the vehicle. turn key to on position.
Select 1 body, 2 them select special funtions
3 slect program key fob,
4 select the number of key fob you want to program.
5 Press and hold the lock and unlock key simultaneous. about 15 seconds
The power lock cycle confirm the remote is programed.

Posted on Jul 03, 2008

Ad
emissionwiz
  • 76846 Answers

SOURCE: keyless remote

THIS IS THE PROCEDURE, FOLLOW IT EXACTLY OR IT WILL NOT WORK.



Transmitter Programming
No Tools Required
In the event that a transmitter is lost, program the old and the new transmitters into the memory of the remote control door lock receiver. Up to 4 transmitters may be programmed.


Important
Once the keyless entry receiver enters the programming/diagnostic mode, the programming of the first transmitter erases all previous transmitter programming information. You must then program all of the transmitters.

Program only 1 vehicle remote control door lock receiver at a time. If you program multiple receivers simultaneously, the same transmitter could possibly be programmed to more than 1 remote control door lock receiver.


Perform the following steps:

Sit in the vehicle driver's seat. (actually it’s much ezr from the front pass seat)
Remove the ignition key from the ignition lock cylinder.
Close all of the vehicle's doors.
Remove the MALL PGM fuse from the fuse panel. Refer to Electronic Diagnosis in Body and Chassis.
Turn the ignition lock cylinder to the ACC position.
Turn the ignition lock cylinder OFF, then back to ACC within 1 second.
Open and then close any vehicle door. You will hear a chime when the remote control door lock receiver enters the programming/diagnostic mode. If you do not hear a chime, start again at step 1.

Important
After 7 seconds, you may hear a chime confirming successful synchronization. After approximately 14 seconds, you will hear a chime confirming successful programming.


Press and hold the transmitter LOCK and UNLOCK buttons simultaneously for 14 seconds.
Repeat step 8 in order to program each additional transmitter.
Remove the ignition key from the ignition lock cylinder.
Install the MALL PGM fuse back into the fuse panel. Refer to Electrical Diagnosis in Body and Chassis.
Validate that all the transmitters that were programmed operate properly. Refer to Keyless Entry System Operation

Posted on Sep 25, 2008

inf12
  • 13 Answers

SOURCE: keyless remote programming insyructions

95 bonny--1-turn ign switch off 2a75c3b.jpg 2-using a fused jumper wire jumper data link connector #8 blk/wht wire to #4 blk wire (look under dash for dlc)
3-press unlock button on 1 transmitter doors should lock and unlock
4-repeat step 3 if doing more than 1 remote
5-remove fused jumper

36a8224.jpgfor the 1993 car same way except jumper term a blk/wht
term g ppl/wht
have fun

Posted on Feb 08, 2009

Molson02536
  • 3854 Answers

SOURCE: How to program a keyless remote for a Pontiac

NOTE: You must have the correct part number on the remote for it to work. The part number you need is 15732803.
Transmitter programming per the GM manual:
Before entering the programming mode, verify the possession of all the transmitters you will be using on the vehicle. Once you program the transmitter, the memory erases the other transmitters. You may program up to 4 transmitters.

  1. Turn OFF the ignition switch
  2. Usa a fused jumper (3 amp is sufficient) and connect terminal 8 (back/white wire) to terminal 4 (black wire)
  3. Close all the doors
  4. Turn ON the ignition switch / the doors will lock
  5. Press and hold the following buttons on one of the transmitters for 30 seconds: lock and unlock
  6. After a 30 second delay, the doors will lock and unlock Important: 
    DO NOT turn OFF the ignition . If the switch is turned OFF the first transmitter becomes inoperative.
  7. In order to program extra transmitters repeat Step 5
  8. Disconnect the fused jumper wire from the data link connector
  9.  Turn off ignition
  10. Verify functions of all programmed transmitters.

This should work for the 1997 and 1999 Bonneville's. Good Luck. Keep me posted, be glad to answerer any other questions you may have. 

Posted on Aug 11, 2009

  • 1 Answer

SOURCE: keyless entry not working pontiac

replace radio fuse even if it looks good then try again

Posted on Sep 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1999 pontiac montana need new key only have pass key


Sorry but you will have to go the the dealer and have them cut and program a new key, good luck.

Mar 19, 2014 | 1999 Pontiac Montana

1 Answer

How to program key fob on 06 Montana SV6 without tech 2


There is no onboard programming procedure for this vehicle. This vehicle requires special equipment be connected to the vehicle to program the keyless remote.

Nov 05, 2012 | 2006 Pontiac Montana SV6

1 Answer

Bought a used 2005 pontiac montana today. Keyless remotes have a mind of their own even after replacing batteries. will lock the car but not unlock and won't open sliding side door. Please help


does your vehicle have an owners manual in it?? sometimes you hafta re-program the remote, to function correctly with the vehicle, and the owners manual will tell you what you need to do.

Dec 05, 2010 | 2005 Pontiac Montana SV6

1 Answer

How do i program a keyless entry remote on an 05 pontiac montana


Hello, this can only be done with a GM tech 2 scan tool.


  1. Install a scan tool.
  2. Use the scan tool in order to access programming: Vehicle Control System/Computer Integrating System/Module Setup/BCM/Program Key Fobs.
  3. Press the START soft key on the scan tool.
  4. Press and hold the LOCK button and the UNLOCK button simultaneously on one transmitter. After a delay of 5-10 seconds, the scan tool will indicate that the transmitter is programmed.
  5. Repeat the previous step in order to program up to 4 transmitters.
  6. Remove the scan tool.
  7. Operate the transmitter functions in order to verify correct system operation.

Nov 07, 2010 | 2005 Pontiac Montana SV6

1 Answer

How to program keyless remote


call you're local dealer -they will give you this info free

Dec 26, 2009 | 2000 Pontiac Montana

1 Answer

I tried the program instructions for my keyless


Here's what I found. Go to this page and select 2006 Grand Prix - http://www.programyourremote.com/classified/Browse.asp?cid=273
You can't program I guess, sorry

Dec 18, 2009 | 2006 Pontiac Grand Prix

1 Answer

New batteries but remote won't click the door(s) or trunk. Ron


try programming the remote again, here is how u do that. if this doesn't fix the problem the remote may be defective, if you need a new one try ebay, they are very cheap to buy there.

.

Note: Existing keyless remotes will be erased with this procedure.
Existing working remotes will have to reprogrammed also.
1. Locate the programming connector wire located in the RH trunk area.
You may have to pull back right side trunk trim on trunk wall to locate
the single black/white wire.

2. The programming connector wire should have one termial in the plastic
connector on end of black/white wire. Ground the terminal in the connector
to a nearby bolt or trunk latch.
Leave connector wire connected to ground through out procedure.
3. System will now lock and unlock doors automatically to indicate
programming mode has been activated.
4. Press any button on keyless remote. System will respond by locking
and unlocking doors one time to indicate successful programming.
5. Repeat step 4 for to program any additonal keyless remotes including
and existing keyless remotes. Do not remove ground wire between
programming of keyless remotes.
6. Disconnect programming connector wire from ground to exit programming
mode.
7. Test keyless remote(s).

Nov 30, 2009 | 1994 Pontiac Grand Prix

6 Answers

Where is the bcm program fuse on a 2005 pontiac montana sv6


The BCM program fuse on a 2005 Montanna SV6 is called something different in the manual. It's called a “Keyless Entry Module” fuse and it is fuse #7. The fuse panel is located on the passenger side on the side of the dash. There is a cover with an indent hole in it to pull the fuse cover off. It's really hard to pull it off and it almost seems like your going to break it when your trying to get if off. Keep pulling, it will come off! On the fuse cover, fuse #7 is labeled " RFA MDLS" which is again different than what is in the manual. I followed the procedure to reprogram my "Key Fob" and within 45secs, I had reprogrammed my key FOB! I was so excited, because, I have been trying locate the BCM fuse for 4 weeks. I think GMC does not want us to know it’s location or name, so you would have to go into a dealership to get your Key Fobs reprogrammed costing about a $100 for a minute of work.
e65ae06.jpg


1. Keep the windows open as a safety measure, then,
2. Remove the ignition key from the ignition lock cylinder.
3. Remove the “RFA MDLS” (fuse #7 ,BCM PRGRM fuse, Keyless Entry fuse) from the fuse panel.
4. Close all of the doors.
5. Close the liftgate.
6. Turn the ignition lock cylinder to ACC.
7. Turn the ignition lock cylinder to OFF, and then back to ACC within 1 second.
8. Open and close any vehicle door. A chime will be heard when the system enters the BCM programming/diagnostic mode.
9. Press and hold the transmitter LOCK and UNLOCK buttons simultaneously for 14 seconds.
10. Important
After 7 seconds, a chime may be heard confirming successful programming.
11. Repeat the previous step on each additional transmitter to be programmed.
12. Remove the ignition key from the ignition lock cylinder
13. Install the “RFA MDLS” fuse ( fuse #7 ,BCM PRGRM fuse, Keyless Entry fuse) back into the fuse panel.
14. Press on the key fob functions (EG. Lock, Unlock) to verify correct operation.

Mar 17, 2009 | 2006 Pontiac Montana SV6

2 Answers

1999 pontiac montana keyless entry


If this is a Factory installed System You will have to get it from the Dealer. If not, You need to find out Who the Manufacturer is of the System and Contact them for a Replacement.

Jan 09, 2009 | 1999 Pontiac Montana

Not finding what you are looking for?
2006 Pontiac Montana SV6 Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8548 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...