Question about Cars & Trucks
I WOULD LIKE TO REPLACE THE SET OF 225/65R16 TIRES WITH 235/65R16 TIRES ON A 2008 DODGE GRAND CARAVAN
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
JUST COMPLETED THIS JOB TODAY. MAKE SURE THE ENGINE HAS COOLED DOWN . IT TOOK APPROX 2 1/2 HRS. DISCONNECT THE NEGATIVE POST ON THE BATTERY. JACK UP PASSENGER SIDE FRONT AND SUPPORT ON JACK STANDS. REMOVE PASS. FROUNT TIRE. DRAIN RADIATOR INTO CONTAINER FOR PROPER DISPOSAL OR REUSE. USING FLOOR JACK PROVIDE SLIGHT TENSION ON OIL PAN WITH A SHORT 2 X 4 WOOD PIECE TO PROTECT OIL PAN. LOOSEN 3 ENGINE MOUNT BOLTS ON PASS. SIDE OF ENGINE COMPARTMENT. ALLOW APPROX 1" BETWEEN SHOULDER OF BOLTS AND MOUNT. LOWER ENGINE UNTILL BOLTS ARE SET ONTO MOUNT. REMOVE ENGINE SPLASH SHIELD INSIDE WHEEL WELL OF REMOVED TIRE. LOCATE WATER PUMP AND LOOSEN 3 PULLEY MOUNTING BOLTS (THIS IS WHILE BELT IS ON PULLEY) REMOVE SURPENTINE BELT AND CONTINUE TO FULLY REMOVE THE PUMP PULLEY. IT WONT COME OUT AS THE PUMP & PULLEY HAVE TO COME OUT TOGEATHER. REMOVE 5 WATER PUMP BOLTS AND CAREFULLY WORK WATER PUMP OUT BETWEEN THE ENGINE AND VEHICLE FRAME. CLEAN ALL MATING/GASKET SURFACES AND BOLTS. USING A SMALL AMOUNT OF TACKY SEALENT TO INSURE THE NEW WATER PUMP SEAL STAYS IN PLACE, THE INSTALL IS PRITTY MUCH THE REVERSAL OF REMOVAL.
GOOD LUCK, REMEMBER TO TIGHTEN ALL BOLTS TO MFR SPECS AND BLEED THE AIR OUT OF THE COOLANT AS REQUIRED.
Posted on Apr 29, 2009
SOURCE: Spare tire location?
With the new 2008 models, the spare tire was moved from the rear of the van to a spot below the front seats. The lug for the tire winch is located under a round cover in the floor just in front of and between the two front seats. If you look under the van, you will see the black tire-shaped cover for the spare.
Posted on May 22, 2009
On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can access the bolts that secure the mirror onto the door
Posted on Sep 29, 2009
Remove the cover plate on the passenger side of the heater box, 3-4 screws.
Unplug the motor assembly, remove 3-4 more screws that hold the motor in place and pull it down from its position. Get an aftermarket motor and installed it in the original housing with the original squirrel cage.
Installation is the reverse of removal.
Posted on Nov 23, 2009
Tips for a great answer:
Dec 25, 2015 | 2010 Dodge Grand Caravan
Dec 05, 2015 | 2005 Dodge Grand Caravan
Nov 26, 2011 | 2008 Dodge Grand Caravan
Jul 06, 2011 | 2008 Dodge Grand Caravan
Jun 06, 2010 | 2008 Dodge Grand Caravan
Jul 19, 2009 | 2008 Dodge Grand Caravan
May 10, 2009 | 2008 Dodge Grand Caravan
18 people viewed this question
Usually answered in minutes!