Question about Toyota Carina

1 Answer

Replacing door light switch which was damage/remove during body works repairs

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Toyota Master
  • 9,098 Answers
Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 3 Answers

SOURCE: Toyota matrix 2004 body door opening seal damaged

use silicone to rebuild it
or
go to auto salvage yard & buy a used one

Posted on Mar 03, 2009

rick_amick
  • 69 Answers

SOURCE: 1998 Chev Malibu. Had damage to passenger doors.

I doubt that shop did anythng wrong by just working on the doors.
I would first check and make sure you have a good ground for the sending unit in the tank. I guess it is possible though that the jolt from the accident could have messed up the sending unit.

Posted on Apr 09, 2009

pchambley
  • 334 Answers

SOURCE: 1997 f150 xl had front

Your not getting power to the s terminal on the starter..Usually the computer grounds a relay and sends the power from the switch to the starter...I would check see if you have a bad relay..Then check the wire from the starter and work backwards,,to the switch

Posted on Sep 19, 2011

emissionwiz
  • 76630 Answers

SOURCE: 2000 Toyota RAV4 side door emblems How do I remove, then replace [higher] RAV4 emblem on side doors to allow fitting of body protection mouldings.

Use an automotive heat gun set to low setting and gently pry the old molding off, then locate an automotive paint/body shop supply store and buy a roll of the special molding double sided tape to put it back on, you will have to buy a whole roll , it will be pricey.

Posted on May 18, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2005 envoy drivers door wont open from inside or outside


Linda, The door latch linkage is probably damaged or fallen off inside the door. Pop into a good body shop and have them check the door lock/latch mechanism for you. The body shop rates tend to be more reasonable then dealership for this type of repair. Links below are just to give you an idea of what may be involved in repair.
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
GMC Envoy door panels remove and install front and rear
How To Install Replace Broken Power Door Lock Front Chevy Trailblazer GMC...
Chevy Truck Door Latch
How chevy door latch works



Jun 22, 2016 | 2005 GMC Envoy

2 Answers

Problems with batteries & alternator 80 Series T/Diesel GXL Auto LandCruiser Would like a Engine wiring diagram if possible. Have had problems since Panel beaters replaced a door on drivers side


sound like you have a bad ground our pwr or short in you wireing sounds like some ine pinched a wire in the door and caused a direct short to ground or your alternator regulator went bad the wrong way supplying youcar with over 14.4 v max 12v reg when you dbl voltage you cut amperage in half and that will fry all electronics and no fuse will blow there for frying B.C.M ,E.C.M P.C.M MULTIFUNCTION SWITCH WIPERS TURN SIGNALS HEAD LIGHTS TAIOL LIGHTS ECT

Dec 04, 2014 | Cars & Trucks

1 Answer

Toyota alarm


wiring or module damaged in collision -- not detected during repair- need t check out wiring in door(s) and to module and the security module.

Apr 01, 2014 | 2007 Toyota Corolla

1 Answer

The door keeps saying it is open and i replaced the door sensers but its not that can you help


Hello melvin... When the light stays on it usually means a door is open or the switch on a door or liftgate/trunk is bad. If the door adjar button is seperate from the latch assembly I pull the switch from the body and jump it out. Go one by one and you will find the failed switch. If the switches check ok and the connector is jumped and the light is still on then there is an open in the wires for the door ajar switch
Here are more procedures for troubleshooting...

Possible causes are :
1. Door switches stuck in closed position. Remove the rubber cover and loosen the screw holding the door switch. Pull out switch and check if the light stays on....if light remains on, fault is not with switches.

2. Anti-theft system ECU shorted. One of the wire goes to the alarm control unit. Unplug the alarm unit, if equipped and test.

3. Shorted interior dome light. If dome light is not working in the door ajar mode, remove the dome light and unplug the connector. If indicator light does not go off, fault is not with dome light.

4. Shorted Red/White wire. This would be the most difficult to diagnose as the shorting can be anywhere between the door switches to the indicator light. If you had done any wiring repairs prior to this happening, backtrack to check if any part of the wire is exposed and grounding

Good luck...i hope this helps.

Jul 17, 2011 | Renault Sport Cars & Trucks

2 Answers

All doors are closed and it said a door is still open


It is probably due to a faulty "jab switch" (the button that the door pushes against when the door closes). Purchase one good jab switch and replace one switch at a time to determine which switch needs replacement. During your diagnosing, when everything works properly, leave that switch in place, it has been repaired. Hopefullly, this will help to FixYa problem!

Oct 13, 2010 | 1996 Ford Explorer

2 Answers

The driver's side outside door handle is loose, toyota celica '95


I assume that the entire handle unit is loose in the body work of the door.
The interior door trim will need to be removed to access the inside of the door to fix the loose handle.

Do not attempt his yourself unless you have some experience in this area.
Take the vehicle to the nearest reputable auto body repair shop and they can easily fix it for you. There could be a breakage on the retaining system on the handle or the retainers may just need tightening.

Typically door handles which have not been subject to damage or abuse will not usually loosen like this. It's possible the door was damaged and the panel repaired and repainted at some stage. If so the door handle may have been removed and refitted in a sloppy manner.

Dec 03, 2009 | 1997 Toyota Camry

1 Answer

1996 ford windstar interior lights stay on battery goes dead


One of the door "sensors" (Door light switches) are to blame - they are usually mounted in the body, and determine the door is open (door position) to supply the ground to the lighting circuit...You can either locate and replace the faulty one, (unplugging each from the back-side removes them individually from circuit)--(Remember to shut all doors, then open one door and remove the connector to each switch to eliminate it from the circuit - until the light goes off- when it goes off- you have found yor culprit) or just pop-out the dome light bulb if it is a high miles car that you aren't interested in repairing,,,,but want the battery to stay charged....Hope that helps - the switches are usually about $5 or $6 each I think,,,,so it's just a bit of effort and time.

Sep 12, 2009 | 1996 Ford Windstar

2 Answers

Car thinks door is open all the time


There is a small switch inside the door area, and it is obviously broken. The switch is usually held in place by 1 screw, and has a wire clip attached to the interior side. If you replace that switch. your issue should cease.

Simply remove the screw that retains that switch, pull it out of the body, remove the wire clip. and install the new switch in reverse.

I hope this information helps you, and I wish you luck on your repair.

May 07, 2009 | 2003 Mercury Mountaineer

1 Answer

INSTALL THE DRIVERS SIDE TAIL LIGHT ASSEMBLY


Save yourself some money and look for a replacement light on ebay or a junk yard. To remove the light open the back hatch and there should be two bolts or screws holding the light in. Remove those screws and slide the light out (may take a little effort to get out). If the body damage is not too bad call a paintless dent repair specialist and see if they can take care of it for a fraction of the cost a body shop would charge........Good Luck

Apr 23, 2009 | 1999 Chrysler Town & Country

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

49 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...