Question about Peugeot Cars & Trucks

Open Question

Idle speed control valve Peugeot 106

How do you clean idle speed control valve

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 133 Answers

SOURCE: IDLE SPEED CONTROL VALVE IN JAG XJ6

Hi the idler valve has a set up with jag equpment but there is a way round this,ifyou have had  O2 sensors changed, is the idler working what are the revs when hot. 650 is to low  850 is ok with a hot engine Mike do you know where the idle valve is and the allen key manual adjustment try a quarter turn but mark it so you can turn it back if need be. let me know how it goes   D    

Posted on Jan 11, 2009

  • 6982 Answers

SOURCE: Frozen Boot Lock Peugeot 106

You can spray solvent into the lock...Do it several times and use the nozzle extension to really get in there. If that does not work, you will need to remove rear seat and use long extensions to unbolt lock from lid.

Posted on Mar 18, 2009

  • 43 Answers

SOURCE: Idle around 1300rpm (X300 4.0L -95)

You can try this diagnostics for the xj6 -4.0L idle speed adjustment.
0c7fddc.png bfc8cff.png
c46737c.png

Posted on Apr 10, 2009

ghost4548
  • 776 Answers

SOURCE: idle speed control

Hmmmmmm.... seems to me you have a completely different problem since you've verified the idle control valve is working. What controls the idle control valve?... AH!... the ECU!... is the wiring between the ECU and the Idle Control Valve in good condition and making good connections? mmmmmmmmm... then I'd say you have a defective computer (ECU). Here's something you might try. Disconnect the battery connection cables from the battery... touch them together (cables + & -) for thirty seconds. Reconnect the cables to the battery and see what happens. Sometimes there's 'GARBAGE' stored in the ECU memory and interferes with the normal operation of components. If nothing changes, you'll need to start testing (bench testing) components (idle speed control actuator (make sure it's not 'sticking'). check for vacuum leaks.... thoroughly inspect intake air hoses & vacuum hoses... inspect all EMS (Engine Management System) connectors for any signs of corrosion or mal-connections (male & female pins). The problem may simply be electrical contacts/connections.. .then again, it could be mechanical.

Posted on Jun 26, 2009

ghost45
  • 1280 Answers

SOURCE: Replacing Idle Air Control Valve on '00 Sonata

No such code: P1520

Posted on Sep 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Engine speeds up and down peugeot 106 independance 2000/01


sounds like either ur iac /or ur tps more then likly ur tps, throtle positioning sensor it controls ur feul intake more feul harder the engine runns, but iac idle air control it tells car more air higher idle less air tells tps less gas lower idle there all linked together have it put on a scanner that will narrow ur possiblities right down to the problem

May 26, 2013 | Peugeot Cars & Trucks

2 Answers

I have replaced idle control valve and car is still over revving,its a 1999 peugeot 206 1.1, mostly sits at 3000rpm but is quite erratic, help plz


Check the fuel pressure regulator for to much pressure.Pull the vacuum hose off the map sensor and if fuel runs out then replace the regulator.

Oct 13, 2012 | 1999 Peugeot 206

1 Answer

My peugeot 406 1.8 XU revs up when started from cold. It then settles down but hunts up and down. It has done this for the past 2 winters. OK in the summer. Have changed the coolant temp probe. Not solved....


You need to clean the throttle valve and the automatic idle speed control valve, follow the procedure below.
Buy a can of spray throttle valve cleaner (it is made by CRC) from the local auto parts store, NEVER USE CARB CLEANING SPRAY, IT DESTROYS THE ANTI-STICK TEFLON COATING, spray it into the air intake through the throttle body of the engine until you have used about half the can, you will need to hold the idle up while you do this, it will try to stall, after this shut the engine down and disconnect the Negative (-) battery cable for 5 minutes. The intake is now clean, if you continue to have the idle speed control problems you may need to seek the help of a professional

Feb 15, 2012 | 1999 Peugeot 406

1 Answer

Diagnostics test says idle air control underspeed error? how do i fix 1999 ford explorer


change the idle air control valve.

Idle Air Control (IAC) Valve OPERATION The Idle Air Control (IAC) valve controls the engine idle speed and dashpot functions. The valve is located on the side of the throttle body. This valve allows air, determined by the Powertrain Control Module (PCM) and controlled by a duty cycle signal, to bypass the throttle plate in order to maintain the proper idle speed. Fig. 1: Typical Idle Air Control (IAC) valve which is mounted to the throttle body - cutaway view shows air bypass direction 89684g16.gif
--- REMOVAL & INSTALLATION
  1. Disconnect the negative battery cable. To remove the IAC valve, first disconnect the negative battery cable, then the IAC wire harness plug 89684p03.jpg
    Next, remove the two IAC valve attaching bolts . . . 89684p04.jpg
    . . . and pull the valve from the intake manifold 89684p05.jpg

  2. Disengage the wiring harness connector from the IAC valve.
  3. Remove the two retaining screws, then remove the IAC valve and discard the old gasket. To install: When installing the valve, always discard the old gasket and install it using a new one 89684p06.jpg

  4. Clean the IAC valve mounting surface on the throttle body of old gasket material.
  5. Using a new gasket, position the IAC valve on the throttle body. Install and tighten the retaining screws to 71-106 inch lbs. (8-12 Nm).
  6. Attach the wiring harness connector to the IAC valve.
  7. Connect the negative battery cable.
prev.gif next.gif

Oct 15, 2010 | 1999 Ford Explorer

1 Answer

Broken Timing belt on peugeot 106 1100 cc will valves & pistons


i presume its a tu engine!? these are very good engines and have been known to survive a broken cam belt. i would try one on it before replacing any valves mate

if this helps let me know
cheers
big mike

Mar 12, 2010 | 1991 Peugeot 405

1 Answer

3.2 liter yamaha engine manual IAC valve How do I replace the IAC valve on this engine? Steps? I just bought a new one and I need to get it replaced. FORD 1994 Taurus SHO 3.2 liter engine YAMAHA


may just need cleaning with carb cleaner.

here is 1996, oldest I have:

Section 03-14: Engine Controls, Electronic 1996 Taurus, Sable Workshop Manual
REMOVAL AND INSTALLATION Idle Air Control (IAC) Valve Removal
  1. Disconnect battery ground cable (14301). Refer to Section 14-01 .
  1. Disconnect the engine control sensor wiring (12A581) from the idle air control valve (IAC valve) (9F715) at the idle air control valve electrical connector.
  1. Remove the two idle air control valve retaining bolts.
  1. Remove the idle air control valve and idle air control valve gasket.
Installation
  1. NOTE: If scraping is necessary, be careful not to damage idle air control valve gasket surfaces, or drop material into intake manifold (9424) or throttle body (9E926) (depending upon application).

    Clean idle air control valve gasket mating surfaces.
  1. To install idle air control valve, reverse Removal procedure.
  1. Tighten the idle air control valve retaining bolts to 8-12 Nm (71-106 lb-in).
33b4417.gif

Jan 14, 2010 | 1994 Ford Taurus

1 Answer

When i started my Peugeot 1.1 this mornig, the


check your idle air control valve.

Dec 20, 2009 | 2005 Peugeot 405

1 Answer

Peugeot 106 when i turn it on it goes into very high revs but nothing seems to be stuck


remove and clean idle speed control valve
if that doesnt cure it replace the idle speed control valve

Aug 28, 2009 | 1991 Peugeot 405

1 Answer

Oil and handbrake lights flashing peugeot 106 s2


Hi, If you solve engine idle speed fault this will stop warning lights.
Oil preasure falls when engine not at norm rpm because oil pump is not turning fast enough.
Put car on diagnostics to check for any fault codes

Aug 04, 2009 | Peugeot 405 Cars & Trucks

1 Answer

Peugeot 206 lx revs up no reason


try cleaning the idle speed control valve this may be sticking

Jun 19, 2009 | Peugeot 504 Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top Peugeot Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Wahs Team

Level 2 Expert

205 Answers

yadayada
yadayada

Level 3 Expert

74896 Answers

Are you a Peugeot Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...