Question about 1998 Isuzu Rodeo

Open Question

Need to replace the starter on 1998 isuzu rodeo

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 84 Answers

SOURCE: replace the alternator on a 97 isuzu rodeo

from Yahoo answers
The alternator is located on the passenger side of the motor at the bottom. There is a bracket attached to the motor and the alternator. You need not take the bracket off to remove the alternator. Two bolts hold the alternator to the bracket. One bolt is on the front top of the alternator and one bolt is located on the bottom front of the alternator. The bottom front bolt is attached to the tension adjustment for the alternator. Loosen the tension screw then remove the bolt going through the tension adjustment. After you loosen the top, front bolt, the alternator should be loose enough to move side to side. Remove the top, front bolt. Now you must disconnect the alternator from the power supply. Behind the alternator is a screw with a wire attached via nut. Remove this wire. Nextly there is a series of wires with a plug on the end. It is plugged into the side of the alternator. Uplug this item. You can also access both of these from the passenger side front tire well. Something to consider is that remanufactured alternators in Rodeo's as well as the Honda Passport (which has the same engine as the Rodeo) do not work and the problem(s) associated with a bad alternator,ie; not charging, no fan blower, battery light and brake light on, still exsist after replacing alternator with reman. Use a factory original alternator if possible. It will cost a little more than a reman but will most likely save you a lot of time and headache!

Hope this helps you out!!
L

Posted on Sep 29, 2008

Ad
  • 1 Answer

SOURCE: need to replace the alternator in a 1998 isuzu rodeo

I have a 1998 Rodeo and just replaced the alternator. If I may make a suggestion, pay someone to do this. It took two of us 4 hours to replace. I am not a certified mechanic, but I know a few things about cars. I thought that I would replace it myself and save a little money! Big mistake. It is EXTREMELY hard to get too and there is NO room to work. Once you get it out, you would think that the new one would just slip back in place, not the case. I will take the car in and have it done next time. To answer your question though, yes you need to go at it from under the right side of the engine. you will need to go from the top to loosen some of the bolts. Hope this helped! Good luck!

Posted on Jan 19, 2009

  • 4 Answers

SOURCE: timing settings for a 1998 isuzu rodeo

You didn't say whether you had a V6 engine or a 4cyl. Here is the procedure for a V6.

It sounds like he moved the cam shaft independently of the crankshaft or other camshaft so you will need to do all these procedures:

1. Turn the crankshaft until the mark on the spocket is lined up with the mark on the oil pump housing (the mark is on the driver's side at 90 degrees to the sprocket itself).

2. Back off the crankshaft counterclockwise 1/8 turn to ensure the pistons aren't at top dead center. This gives the valves room to move without hitting the piston.

3. Turn the passenger's side camshaft until it "jumps" into place with the alignment mark on the camshaft pully is pretty close to being lined up with the mark on the engine head.

4. Turn the driver's side camshaft until it "jumps" into place but this won't be perfectly lined up with the mark but will be about an 1/8 turn off from the mark. Then line it up by hand.

5. The idler pulleys and tensioner pulleys should be installed on the engine but the tenioner pulley adjuster (it is a little cylinder with a rod coming out of it that is held in place by 2 bolts) should be removed.

6. Place the new belt on the crankshaft first. Be sure the arrows on the belt point in a clockwise direction. If you have a belt with lines and dots then the lines will line up with all markings that you have lined up together. The dots should line up at the 270 degree point on the crankshaft (opposite of the lines and the markings).

7. Loop the belt around the tensioner pulley, around the passenger's side cam, under the waterpump, around the driver's side cam, and finally around the idler pulley. Check all alignments.

8. Put the tesioner adjuster in a vise and squeeze it together until you can place a small drill bit or allen wrench through the holes to keep it compressed.

9. This is the tricky part. You will need to install the tensioner adjuster and that will require some moving of the belt to allow enough play to get the adjuster in place. This may move the passenger's side alignment. If so, you will need to try it again. I find that if you move passenger's side alignment mark clockwise by one tooth of the sprocket, then when you go to put the tensioner in place it lines up. You may find other tricks to overcome this challenge.

10. Once you think you have everything lined up. Use a wrench to turn the crankshaft sprocket 2 full turns. Listen closely and feel for any hard resistance as you do this to determine if the pistons are hitting the valves. If you believe they are hitting each other thenrepeat the adjustment procedure. Not doing this can ruin the valves or more.

11. If everything seems OK. remove the drill bit or allen wrench from the tension adjuster. Perform step 10 again for one final check.

I hope this helps.

Posted on Feb 22, 2009

  • 1 Answer

SOURCE: can not get starter out of my 1998 isuzu rodeo

The best way to do it is to unbolt the engine mounts and lightly lift the engine from below with your floor jack and a piece of wood. Trust me, that the only way I could get it out. 3 Hours to get it out, 10 minutes to get the new one in place.

Posted on Mar 27, 2009

  • 22 Answers

SOURCE: replacing the power steering pump on a 1998 isuzu rodeo

Remove low pressure and high pressure hoses (this one could be hard to break loose). You might want to have an oil pan handy, to capture the oil. Disconnect electrical sensor. Remove the bolt that holds belt tension adjustment plate. And finally remove the bolt that holds the pump in place. It is bolted from the back and located at the right lower corner of the pump if you are facing the front of the car. Remove the pump assy. I could not remove belt pulley at home, no matter how hard I tried. Ended up taking it to an automotive shop and they removed it in no time, using one of those "pneumatic impact guns". Assemble new pump. Fill the reservoir with PS oil. Make sure both of the front wheels are off the ground, start the engine and slowly spin the steering wheel back and forth for about 5 minutes or untill screeching sound stops and the liquid in the reservoir stops foaming. That will bleed any air that is in the system. Don't go all the way to the end of stroke. Good luck.

Posted on May 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What does the starter relay fuse for a 1998 Isuzu rodeo look like and where is is located in the fuse box


Crystal, this is what I found on the Rodeo starter fuse/relay.
Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
99 Isuzu Rodeo LS Underhood Fuse Box Diagram Circuit Wiring Diagrams
1997 Isuzu Rodeo Question Fuse Box Diagram Electrical Problem
1999 Isuzu Rodeo Main Fuse Box Diagram Circuit Wiring Diagrams
1998 Trooper Relay Solenoid Starter 1998 Isuzu Trooper All of

Jul 06, 2016 | Isuzu Cars & Trucks

1 Answer

1998 Isuzu rodeo headlights not working. changed fuses, and bulbs , still not working


What does tried mean ?

You could not figure out if a fuse had failed?

You tested no fuses & replaced perfectly good ones?

You replaced head light lamps & did not test the old ones?

If the cable from the battery to the starter was an issue
Would you not have checked that?

If it was an issue, then the vehicle most likely wouldn't start

Not really telling us anything that was tested

Your asking for a guess to what?




Oct 21, 2014 | 1998 Isuzu Rodeo

1 Answer

COST OF STARTER REPLACEMENT ON ISUZU RODEO 1998


costs vary by a zillion factors.
country
city.
shop
taxes, rent, labor costs, insurance.
and if the parts are rusty. or related parts are destroy'd.
and if old parts have core value.
why ask here, we know NONE of this,
ask your mech. ask them, in your town.

Jul 14, 2014 | 2003 Isuzu Rodeo

1 Answer

198 isuzu rodeo starter clicks but doesn't engage and lights do not dim. alarm chirped unlocking. why wont it start?


Your battery has enough amps and voltage to power up the accessories, but does not have enough amps to engage the starter motor. The click you here at the starter is the solenoid trying to allow the starter motor to turn. Either replace the battery and/or check the battery connections for corroded terminals.

Jan 01, 2011 | 1998 Isuzu Rodeo

1 Answer

WHERE IS THE STARTER AT IN A 1998 RODEO


Bottom Left side of engine
Let me know if this help you....

57579d2.jpg

Oct 04, 2009 | 1998 Isuzu Rodeo

2 Answers

I want to know where is the starter located in a izuzuz rodeo 1998


The starter is no the driver side, right above the exaust pipe. Just a hint if you have to replace the starter you have to remove the pipe to get it out and back in.

Jul 13, 2009 | 1998 Isuzu Rodeo

1 Answer

Interchangeable any other model ?


1994-2002 Passport
1998-2000 Amigo
1993-2004 Rodeo
2001-2003 Rodeo Sport
2002-2004 Axiom

Jun 19, 2009 | 1998 Isuzu Rodeo

2 Answers

How to remove starter from 1998 isuzu rodeo 4 whl drive 6 cyl?


disconnect the battery first. remove the 3 bolts connecting the starter the the bellhouseing, the remove the wires. install in reverse order

Jun 04, 2009 | 1998 Isuzu Rodeo

2 Answers

Siezed engine or not?


If it was Running good Prior to this it is the Starter.

Jan 22, 2009 | 1998 Isuzu Rodeo

Not finding what you are looking for?
1998 Isuzu Rodeo Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14384 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...