Question about Nissan Cars & Trucks

Open Question

Where is the neutral safety switch on case ih 2388 combine

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

chryslertech
  • 115 Answers

SOURCE: Location of NSS(neutral safety switch) on 2002 Dodge Caravan

It is in side the trans on top of the valve body. Why do you think you need to replace it?

Posted on Mar 03, 2009

  • 1 Answer

SOURCE: 2004 Jeep Grand Chrokee Neutral Safety Switch Location

The switch is on the transmission..It is usually a dealer item but you can get one from Rockauto.com for about 1/4 of what the dealers charge.

Posted on May 25, 2009

emissionwiz
  • 75822 Answers

SOURCE: Neutral Safety Switch Location

on the transmission where the shift cable attaches.

Posted on Jun 15, 2009

  • 1129 Answers

SOURCE: neutral safety switch

It is located on the side of the transmission, follow the shift cable down to it you will recognize it because it has a electrical wire comming off it and either a shift lever or shift cable going to it.

Posted on Jul 14, 2009

ZJLimited
  • 17970 Answers

SOURCE: Looking for the neutral safety switch

Neutral Safety/Back-up Light Switch

This is a combination switch which controls both Neutral Safety and Back-up lamp circuits.

C6 Transmission


8290dff.jpg

C6 neutral start switch

  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle on jackstands.
  3. Remove the downshift linkage rod return spring at the low-reverse servo cover.
  4. Coat the outer lever attaching nut with penetrating oil. Remove the nut and lever.
  5. Remove the 2 switch attaching bolts, disconnect the wiring at the connectors and remove the switch.
  6. Installation is the reverse of removal. Adjust the switch and tighten the bolts to 55-75 inch lbs. (6.2-8.5 Nm).
  7. Remove the jackstands and lower the vehicle.
  8. Connect the negative battery cable.
AOD Transmission

e7f4231.jpg

Removing the AOD neutral start switch
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle on jackstands.
  3. Disconnect the wiring from the switch.
  4. Using a deep socket, unscrew the switch.
  5. Installation is the reverse of removal. Tighten the switch to 10 ft. lbs. (14 Nm).
  6. Remove the jackstands and lower the vehicle.
  7. Connect the negative battery cable.
4R70W Transmission

2f68dfc.jpg


Removing the Manual Lever Position (MLP) sensor

As of 1994, the neutral safety switch is referred to as a Manual Lever Position Sensor (MLP).
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle on jackstands.
  3. Disengage the harness connector from the MLP sensor.
  4. Remove the 2 sensor attaching bolts and remove the sensor.
To install:
  1. Install the MLP sensor and install retaining bolts. Do not tighten, the sensor requires adjustment.
  2. Adjust the MLP sensor then tighten attaching screws to 80-100 inch lbs. (9-11 Nm).
  3. Remove the jackstands and lower the vehicle.
  4. Connect the negative battery cable.


ADJUSTMENT

C6 Transmission
  1. Hold the steering column transmission selector lever against the Neutral stop.
  2. Move the sliding block assembly on the neutral switch to the Neutral position and insert a 0.091 in. (2.3mm) gauge pin in the alignment hole on the terminal side of the switch.
  3. Move the switch assembly housing so that the sliding block contacts the actuating pin lever. Secure the switch to the outer tube of the steering column and remove the gauge pin.
  4. Check the operation of the switch. The engine should only start in Neutral and Park .

4R70W Transmission


4cc4151.jpg


Adjusting the MLP sensor

Park is the last detent when the manual control lever is full forward. Return 2 detents toward the output shaft for Neutral.
  1. Position the manual control lever in Neutral .
  2. Insert Gear Position Sensor Adjuster tool T93P-700 10-A or equivalent, into the slots.
  3. Align all 3 slots on the MLP sensor with 3 tabs on the tool.
  4. Tighten the attaching screws to 80-100 inch lbs. (9-11 Nm).

I hope help you. Good luck (rated this help).

Posted on Sep 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is neutral safety switch on 05 GMc envoy Denali


The transmission range (TR) switch is part of the park/neutral position (PNP) and backup lamp switch assembly, which is externally mounted on the transmission manual shaft. The TR switch contains four internal switches that indicate the transmission gear range selector lever position. The powertrain control module (PCM) supplies ignition voltage to each switch circuit. As the gear range selector lever is moved, the state of each switch may change, causing the circuit to open or close. An open circuit or switch indicates a high voltage signal. A closed circuit or switch indicates a low voltage signal. The PCM detects the selected gear range by deciphering the combination of the voltage signals. The PCM compares the actual voltage combination of the switch signals to a TR switch combination chart stored in memory.

Apr 14, 2017 | GMC Cars & Trucks

1 Answer

Why my99 honda accord wont shift to drive


bad neutral safety switch,here's a link to it, Repair Guides Instruments And Switches Back up Light Switch AutoZone com

Neutral Safety Switch

Print
DESCRIPTION

The neutral safety switch is a combination switch that also controls the backup lights and gear position indicators. The switch is located on the transaxle assembly.Here's a link to the part.
Duralast Neutral Safety Switch JA4308 1999 Honda Accord EX 6 Cylinders...

Sep 04, 2014 | Cars & Trucks

1 Answer

Netural safety switch


Daewoo cars have track record for dependability in addition to solid construction. The most important part of a car's design is the safety features. Circumvent excessive risk while motoring by insuring that your car has the safety gear that you want. A vehicle's Neutral Safety Switch is located on your clutch in the case that it's a manual transmission, and on the shifter in an automatic. A broken Neutral Safety Switch can cause your vehicle to suddenly start in gear, causing vehicle damage or personal injury.

If you don't have the Neutral Safety Switch, your vehicle will fail to work. The Neutral Safety Switch is typically situated below the clutch of trucks which have a stick-shift transmission. The primary function of a Neutral Safety Switch is to stop your truck from starting when in gear. The car's Neutral Safety Switch acts as a safety feature, keeping you from starting the engine if the car is in gear. The Neutral Safety Switch is an electronic part which is essential while starting your car.Here's a link to what it look's like.

Mar 22, 2013 | 2000 Daewoo Lanos

1 Answer

2003dodge caravan neutral safty switch


Test/Service/Replace Neutral Safety Switch
Most neutral safety switches are combinations of a neutral safety switch and a backup lamp switch. Others have separate units for these two distinct functions. When the reverse light switch is not part of the neutral safety switch, it seldom needs adjustment, as it is directly activated by the transmission or the gear selector linkage.
f_ttat_t3.20.jpg Typical location of a neutral safety switch on a transaxle. Reprinted with permission of Ford Motor Company. A neutral safety switch allows current to pass from the starter switch to the starter when the lever is placed in the P or N position. Some neutral safety switches are nonadjustable. If these prevent starting in the P or N position and the gear selector linkage is correctly adjusted, they should be replaced.
To adjust a typical neutral safety switch:
  • Place the shift lever in neutral.
  • Loosen the attaching bolts for the switch.
  • Using the angling pin, move the switch until the pin falls into the hole in its rotor.
  • Tighten the attaching bolts.
  • Recheck the switch for continuity. If no voltage is present, replace the switch.
  • The switch sometimes controls the operation of the back-up lights also. With the engine off and the key on, put the selector in reverse position. Check the back-up lights to see that they are on. Then, check in the drive position to see that they are out.

Aug 15, 2012 | Cars & Trucks

1 Answer

Is the neutral switch the same as the transaxle range switch?


Yes they are the same part just different names. The neutral safety is part of the transmission/transaxle range selector combination switch.

May 17, 2012 | 1993 Mazda Protege

1 Answer

Where is neutral switch on a 92 dodge caravan


Safety Switch Most neutral safety switches are combinations of a neutral safety switch and a backup lamp switch. Others have separate units for these two distinct functions. When the reverse light switch is not part of the neutral safety switch, it seldom needs adjustment, as it is directly activated by the transmission or the gear selector linkage.
f_ttat_t3.20.jpg Typical location of a neutral safety switch on a transaxle. Reprinted with permission of Ford Motor Company. A neutral safety switch allows current to pass from the starter switch to the starter when the lever is placed in the P or N position. Some neutral safety switches are nonadjustable. If these prevent starting in the P or N position and the gear selector linkage is correctly adjusted, they should be replaced.
To adjust a typical neutral safety switch:
  • Place the shift lever in neutral.
  • Loosen the attaching bolts for the switch.
  • Using the angling pin, move the switch until the pin falls into the hole in its rotor.
  • Tighten the attaching bolts.
  • Recheck the switch for continuity. If no voltage is present, replace the switch.
  • The switch sometimes controls the operation of the back-up lights also. With the engine off and the key on, put the selector in reverse position. Check the back-up lights to see that they are on. Then, check in the drive position to see that they are out.

May 10, 2012 | 1992 Dodge Caravan

1 Answer

Where is the neutral safty swith on a 2006 ford focus


There isnt a neutral safety switch. There is a manual lever position sensor(MLP). It combines all the fuctions of backup lights, neutral safety, and informing the PCM what gear you have selected into one unit. Follow the shift cable out to the transmission, and at the end, Follow the shift cable out to the transmission, and at the end, you will find the MLP.
Pendin if its auto or manual

Mar 20, 2011 | 2000 Ford Focus

1 Answer

1971 ford f100 pickup neutral safety switch wiring color code


Ford Neutral Safety Switch; Ford Reverse Light Switch; Backup Light Switch.

The Neutral Safety Switch wires in my 1971 Ford F100 are orange with a blue stripe.
The Reverse, or Backup Light Switch wires are black with a red stripe.

There are two sets of two wires across this combined neutral safety and backup light switch, for a total of 4 wires. Photos are at the end of this post.

The switch for the 1971 Ford F100 pickup truck is the same as in many other years and models. For details, including parts numbers, see the following quote from an expert at Ford Truck Enthusiasts:
http://www.ford-trucks.com/forums/287185-back-up-light-and-neutral-safety-switch-2.html#post5601846

The neutral switch also controls the backup lights, and is the same 1967/77.

C7TZ-7A247-A .. Neutral/Backup Switch (Motorcraft SW-600)

There is no separate backup light switch..except on 1967/68 F350's.

Neutral switch location 1967/77:

The plastic half moon shaped neutral safety switch mounts on the outside lower portion of the steering column (NOT on the transmission!).

It's activated by an inverted Y shaped lever that snaps on the shift tube

D0TZ-7B097-B .. Lever, Neutral Switch Actuator = From FTE sponsor DIRECT FORD PARTS: Ford suggested retail price: $18.72 / FTE member net: $13.23.

The switch is also still available from Ford, but the website is down so I can't post the list & net prices. .

1978 is the FIRST year the F100/350's have the neutral switch mounted on the transmission. __________________

Bill // Retired Ford Parts Manager // SoCal Chapter member // Part Number Research: 1928/2001 FoMoCo vehicles.

IMAGES
jim_pivonka.jpg
Driver side of the neutral / reverse switch showing the travel slot for the switch arm, the return tensioning spring, and the arm.

jim_pivonka_0.jpg
The front, steering wheel side of the neutral / reverse switch after removal from the steering column. The switch's two functions are actuated when the lever in the column moves the switch lever shown here to different positions as gears are selected.

jim_pivonka_1.jpg
The neutral switch is installed on the steering column near the firewall, with 5/8" bolts into the steering column (visible hole) and down column from a rectangular opening in the column housing. The actuating lever for the switch is attached to the gear shift shaft inside the housing; the lever is visibly protruding from the opening in this image.

jim_pivonka_2.jpg
Back of neutral / reverse switch, showing the wiring attachments. Black with red stripe is the backup light wiring, Orange with blue stripe is the neutral safety switch, it prevents starting in gears other than neutral & park.

Aug 03, 2010 | Ford F-100 Cars & Trucks

2 Answers

Bronco wont start 88 ford bronco just replaced tranny and now won't start. i've hooked everything back up but one of the wires to the transfer case bc i broke the plug in. any ideas why it wont start...


The neutral safety switch is located on the side of the transmission and it is usually attached behind the shifter linkage and it is secured with two small bolts that can be loosened up to allow for adjustment of the neutral safety switch.

To adjust the neutral safety switch place the transmission into neutral, (block the tires) there is a notch or and indent marker on the housing of the neutral safety switch that should be lined up with a line on the face of the collar that is around the shifter detent shaft, and if they are not in alignment then loosen the two bolts that secure the neutral safety switch and then turn the neutral safety switch until they are aligned and then tighten the securing bolts to the neutral safety switch, and then test the starter. If the starter fails to engage then either the neutral safety switch is faulty, the neutral safety switch has been by-passed all this time and the by-pass (I will usually find things like a paper clip shoved into the vehicles wire connector with electrical tape around it) has fallen out of the wire connector from the vehicle wiring harness, or the battery just went dead. if you have the neutral safety switch from the old transmission still available try using it to test the neutral safety circuit. I have provided you with an image to help assist you adjust the neutral safety switch.


0b4222e.jpg

Jun 20, 2010 | 1988 Ford Bronco

1 Answer

Where is the neutral safety switsh located? on a 95 dodge stratus


the neutral safety switch (Park/Neutral position switch) is located to the right of the transaxle range switch on the front of the transaxle, just above the fluid pan.
  1. Disconnect the negative battery cable.
  2. Safely raise and support the vehicle.
  3. Disengage the electrical connector from the switch.
  4. Unscrew the switch from the transaxle case.
To install:
  1. Position a new seal washer, then screw the switch into the transaxle case.
  2. Attach the electrical connector to the switch.
  3. Lower the vehicle.
  4. Connect the negative battery cable.

May 25, 2010 | 1995 Dodge Stratus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

73 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...