Question about 2002 Ford Crown Victoria

Open Question

Diagram for dash removingfrom 1997 crown victoria

Heater core

Posted by on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 7 Answers

SOURCE: How to take out dash

I agree with 'jthall1', it is a major pain! Undo every bolt and screw visible to the eye. Then you have to find the ones that you can't easily see! (They are near the defroster vents and under the dash and also behind the glovebox.) Now that you have it lose and it still won't come down for you, you have to remove the, i believe its 2, bolts holding you steering column up. At this point you can now pull the dash down and gain access to the heater core, which you will probably have to ***pry*** off the firewall. As previously stated, IT IS A PAIN!!!!!!!!!! PS- Don't forget to take the lines and bolts off the heater core from under the hood!

Posted on Aug 16, 2008

Ad
  • 202 Answers

SOURCE: 1999 crown victoria

You don't.
The dash has to come out in order to remove the HVAC box to get to it.

Posted on Apr 29, 2009

c17hydro
  • 2984 Answers

SOURCE: heater core

No, you don't have to pull the whole dash board but you have to pull a few panels....here is the steps on how to get to it and remove and replace it:

  1. Disconnect the negative battery cable.
  2. Drain the cooling system and disconnect the heater hoses from the heater core tubes. Plug the hoses and the heater core tubes to prevent coolant leakage.

CAUTION NEVER open, service or drain the radiator or cooling system when hot; serious burns can occur from the steam and hot coolant. Also, when draining engine coolant, keep in mind that cats and dogs are attracted to ethylene glycol antifreeze and could drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantities. Always drain coolant into a sealable container. Coolant should be reused unless it is contaminated or is several years old.


  1. Remove the 3 nuts located below the windshield wiper motor attaching the left end of the plenum to the dash panel. Remove the 1 nut retaining the upper left corner of the evaporator case to the dash panel.

935a10f.gif
Plenum removal—1990-98 vehicles

  1. Disconnect the vacuum supply hose(s) from the vacuum source. Push the grommet and vacuum supply hose(s) into the passenger compartment.
  2. Remove the right and left lower instrument panel insulators.
  1. On 1989 vehicles:
  2. Remove the 3 glove compartment hinge screws, disconnect the check arms and remove the glove compartment.
  3. Loosen the right door sill plate and remove the right side cowl trim panel.
  4. Remove the bolt attaching the lower right end of the instrument panel to the side cowl.
  5. Remove the instrument panel pad as follows:
    • Remove the 2 screws attaching the pad to the instrument panel at each defroster opening. Be careful not to drop the screws into the defroster openings.
    • Remove the one screw attaching each outboard end of the pad to the instrument panel.
    • On Crown Victoria, remove one pad attaching screw near the upper right corner of the glove compartment door.
    • Remove the 5 screws attaching the lower edge of the pad to the instrument panel. Pull the instrument panel pad rearward and remove it from the vehicle.
  6. On 1990-98 vehicles:
  7. Remove all instrument panel mounting screws and pull the instrument panel back as far as it will go without disconnecting any wiring harnesses.
  8. Make sure the nuts attaching the instrument panel braces to the dash panel are removed.
  9. Loosen the right door sill plate and remove the right side cowl trim panel.
  10. If equipped with manual air conditioning, disengage the temperature control cable housing from the bracket on top of the plenum. Disconnect the cable from the temperature blend door crank arm.
  11. If equipped with Automatic Temperature Control (ATC), proceed as follows:
  12. On 1989 vehicles, disconnect the temperature control cable from the ATC sensor.
  13. Detach the vacuum harness line connector from the ATC sensor harness and detach the electrical connector from the ATC servo connector.
  14. On 1990-98 vehicles, remove the cross body brace and disconnect the wiring harness from the temperature blend door actuator. Detach the ATC sensor tube from the evaporator case connector.
  15. Detach the vacuum jumper harness at the multiple vacuum connector near the floor air distribution duct.
  16. Disconnect the white vacuum hose from the outside-recirculating door vacuum motor.

572e87e.gif
Floor air distribution duct removal—1990-98 vehicles
  1. Remove the 2 hush panels.
  2. Remove 1 plastic push fastener retaining the floor air distribution duct to the left end of the plenum.
  3. Remove the left screw and loosen the right screw on the rear face of the plenum and remove the floor air distribution duct.
  4. Remove the 2 nuts from the 2 studs along the lower flange of the plenum.

a3c9f99.gif
Heater core removal—1990-98 vehicles

  1. Carefully move the plenum rearward to allow the heater core tubes and the stud at the top of the plenum to clear the holes in the dash panel. Remove the plenum from the vehicle by rotating the top of the plenum forward, down and out from under the instrument panel. Carefully pull the lower edge of the instrument panel rearward, as necessary, while rolling the plenum from behind the instrument panel.
  2. On 1989 vehicles with ATC, remove the ATC servo from the plenum.
  3. Remove the 4 retaining screws from the heater core cover and remove the cover from the plenum assembly.
  4. Pull the heater core and seal assembly from the plenum assembly.
To install:
  1. Carefully install the heater core and seal assembly into the plenum assembly. Visually check to ensure that the core seal is properly positioned. Position the heater core cover and install the 4 retaining screws.
  2. On 1989 vehicles with ATC, install the ATC servo on the plenum.
  3. Route the vacuum supply hose through the dash panel and seat the grommet in the opening.
  4. Position the plenum under the instrument panel with the register duct opening up and the heater core tubes down. Rotate the plenum up behind the instrument panel and position the plenum to the dash panel. Insert the heater core tubes and mounting studs through their respective holes in the dash panel and the evaporator case.
  5. Install the 3 nuts on the studs along the lower flange and one on the upper flange of the plenum. Install the 3 nuts below the windshield wiper motor to attach the left end of the plenum to the dash panel and the one nut to retain the upper left corner of the evaporator case to the dash panel.
  6. Position the floor air distribution duct on the plenum. Install the 2 screws and plastic push fastener. If removed, position the panel door vacuum motor to the mounting bracket and install the 2 attaching screws.
  7. Connect the white vacuum hose to the outside-recirculating door vacuum motor. Attach the vacuum jumper harness to the plenum harness at the multiple vacuum connector near the floor air distribution duct. Install the floor duct.
  8. If equipped with manual air conditioning, connect the temperature control cable housing to the bracket on top of the plenum and connect the temperature control cable to the temperature blend door crank arm. Adjust the temperature cable.
  9. If equipped with ATC, proceed as follows:
    1. On 1989 vehicles, connect the temperature control cable to the ATC sensor and adjust the cable. Route and attach the vacuum harness connector to the ATC sensor and attach the electrical connector to the ATC servo connector. Do not block the sensor aspirator exhaust port with the excess vacuum harness. Install the ATC sensor tube between the sensor and the evaporator connector.
    2. On 1990-98 vehicles, attach the ATC sensor tube to the evaporator case connector. Install the cross body brace and connect the wiring harness to the blend door actuator.
  10. Install the bolt to attach the lower right end of the instrument panel to the side cowl. Install the right side cowl trim panel and tighten the right door sill plate attaching screws.
  11. On 1989 vehicles, install the instrument panel pad and the glove compartment door. On 1990-98 vehicles, push the instrument panel back into position and install all instrument panel mounting screws. Install the right and left lower instrument panel insulators.
  12. Connect the vacuum supply hose(s) to the vacuum source.
  13. Install the right and left lower instrument panel insulators and install the 2 hush panels.
  14. Unplug the heater core tubes and the heater hoses and connect the heater hoses to the heater core tubes. Fill the cooling system.
  15. Connect the negative battery cable and check the system for proper operation.

Posted on Feb 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have 1998 crown Victoria and have replaced heater coreand now the car wont start... Any suggestions?


heater core means you had the dash all apart , yes?
that means the computer wiring is in that mess too.
run a computer test 1st

May 03, 2015 | 1998 Ford Crown Victoria

1 Answer

Instructions for replacing heater core in 1986 ford crown victoria LTD


Remove dash

disconnect heater core hoses in the engine compartment

open heater box, and remove the heater core.

Mar 01, 2014 | 1986 Ford Crown Victoria

1 Answer

Changing the heater core on a 1998 Crown Victoria


this job is not for the faint of heart! the dash board must be removed! if you would like to proceed email me and ill guide u the rest of the way

Mar 19, 2010 | 1998 Ford Crown Victoria

1 Answer

How do i get to my heater core 1995 ford crown vic


Your heater core is located behind the dash. You need to remove the dashboard and your heater core will be located on the passenger side along the firewall. It will look like a small radiator. Get yourself a haynes manual for good step by step instructions and pictures to remove your dash.

Jan 03, 2010 | 1995 Ford Crown Victoria

1 Answer

WHAT DO I REMOVE TO REPLACE HEATER CORE IN 1996 CROWN VICTORIA?


The dash has to be removed. The evaperator case has to be pulled forward to get to the clip or nut holding the heater case. It is a big job. If you are not comfortable removing the dash do not try it.

Dec 02, 2009 | 1994 Ford Crown Victoria

1 Answer

I have a 1995 crown victoria lx. heater core needs replacement. is it possible to access it by cutting the firewall instead of going through the process of removing the dash.


No you don't want to hack up your car like that. You are going to have to not completely remove the dashboard just loosen the bolts holding it and pull the right side section of it back enough to access the heater core you can use some wire to hold the right side of the dash in place.

Nov 30, 2009 | 1995 Ford Crown Victoria

1 Answer

My crown victoria is leaking radiator water inside the car. mainly on the passenger side beneath the glove compartment. It smells really bad, and I can't find the leak. Is there any way to get detailed...


Yes, it's the cars heater core leaking. The heater core is like a mini radiator under the dash-coolant circulates through it from the engine to provide the heat. To change the heater core is a very labor intensive job. You really need to get a repair manual, or go online to 'alldata' diy repair where you can sign up for 1 year or more access to your Crown Vics repair info. Excellent source for diagrams and instructions. I believe one year is $16.95, good for ONE car info for a year.

May 01, 2009 | 1996 Ford Crown Victoria

1 Answer

1999 crown victoria


You don't.
The dash has to come out in order to remove the HVAC box to get to it.

Apr 29, 2009 | 1999 Ford Crown Victoria

3 Answers

1999 Crown Victoria


the heater core is leaking.

Oct 24, 2008 | 1999 Ford Crown Victoria

2 Answers

How to take out dash on 1997 crown victoria to replace heater core


I agree with 'jthall1', it is a major pain! Undo every bolt and screw visible to the eye. Then you have to find the ones that you can't easily see! (They are near the defroster vents and under the dash and also behind the glovebox.) Now that you have it lose and it still won't come down for you, you have to remove the, i believe its 2, bolts holding you steering column up. At this point you can now pull the dash down and gain access to the heater core, which you will probably have to ***pry*** off the firewall. As previously stated, IT IS A PAIN!!!!!!!!!! PS- Don't forget to take the lines and bolts off the heater core from under the hood!

Aug 13, 2008 | 1994 Ford Crown Victoria

Not finding what you are looking for?
2002 Ford Crown Victoria Logo

Related Topics:

274 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...