Question about Honda Cars & Trucks

Open Question

Hi there i have a honda luxline 160i 92 model not reffinineg over 3500 refs engine light is on showing error code 4 and 7 replaced the parts twice already but it keeps on blowing i only drive for a week or so than it blows again checked out the computer box and its fine and also the car idles very low when its cold and the moment it warms up than it idles over 2000 refs can u help please been struggling for months already

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: this is the error message. Farmville error. Pls

this is the problem. error on farmville

Posted on Dec 06, 2009

Ad
webmaster21
  • 803 Answers

SOURCE: Farmville error. Pls help.

What web browser are you using. On thingyou can try is closing your web browser and opening it up again and reloading FarmVille. That should fix the problem. Thanks for using Fixya. ~WEBMASTER21

Posted on Dec 06, 2009

bandg963
  • 43 Answers

SOURCE: ac not blowing cold air, is is the thermostat?

Charge your a/c system.

Posted on Sep 07, 2012

  • 239 Answers

SOURCE: my air conditioner isnt blowing cold air

is the ac a manual one or automatic? if it's manual then it froze and will no longer work. it froze and is all done working. time for a new one. I bought one 12 years ago and apparently I was suppose to turn on and off. The ac couldn't do that. IF it works on it's own maybe the circuit isn't the higher amp for 220 ac units.

Posted on Sep 07, 2012

Hobbit_who
  • 2044 Answers

SOURCE: HONDA BALLADE 160I CUTTING OUT AT 3500 RPM

The Nippon-Denzo Distributor's are known to have problems. I had the same issue for 3 months where it would cut out and sometimes, actually kill my car. Finally I spend the $200 and put a new Distributor in the car and it fixed my problems. there are 2 different Distributors for your car, make sure you get the right one or it will not work.

Posted on Mar 03, 2014

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1996 honda 160i luxline remote imobilzer programing


reset immobiliser I HAVE A HONDA CIVIC 1.6 LUXLINE ...

www.fixya.com/cars/t23058317-reset_immobiliser
Jan 22, 2014 - reset immobiliser I HAVE A HONDA CIVIC 1.6 LUXLINE 1998. I NEED TO BYPASS THE IMMOBILSER TO START THE CAR WITHOUT IT ... Press any button on remote one time within 20 seconds. .... How can i fix my honda 160i luxline92 model starting difficulty? Jul 20 ... Jun 09, 2012 ' 1996 Honda Civic.

Sep 27, 2015 | Honda Cars & Trucks

1 Answer

My honda 160i 1992 luxline is cutting out when driving over 80 and when i release the pedal its driving orite


Could be the throttle position sensor or the pedal position semsor is playing up, might be that a diagnostic might show what the problem is.

Before you do that ensure that you engine is in good tune, this will save time and money in the long run

Jul 16, 2015 | Honda Cars & Trucks

1 Answer

I have a honda ballade 160i luxline '93 model with a over heating problem when i go on long continuous drives even though my cooling fan works on temperature. my idling of my car is also not s


Change the thermostat? Probably did, since you went after the computer. Does the car really over heat? Or does the gauge just go high(bad gauge). If the engine does over heat, then it could be the water pump, or to much sediment in the engine(Something blocked). I have seen both.

Jan 20, 2015 | Honda Cars & Trucks

1 Answer

How can i fix my honda 160i luxline 92 model starting difficulty?


Yes, you need to set your camshaft end distributor timing to TDC. (top dead centre). now you start vehicle, and adjust your distributor timing to 10% after tdc, on the coast or 8% inland

Jul 20, 2014 | Honda Accord Cars & Trucks

1 Answer

HONDA BALLADE 160I CUTTING OUT AT 3500 RPM


The Nippon-Denzo Distributor's are known to have problems. I had the same issue for 3 months where it would cut out and sometimes, actually kill my car. Finally I spend the $200 and put a new Distributor in the car and it fixed my problems. there are 2 different Distributors for your car, make sure you get the right one or it will not work.

Mar 03, 2014 | Cars & Trucks

2 Answers

Cutting out at 3500 rpm


Check if the air filter is clogged with oil and dirt. Check the timing, then check that the cam belt has not slipped. Could be plug wires, but this will usually cause rough running as well. Could be low fuel pressure.

Mar 01, 2014 | 1991 Honda Civic

1 Answer

I need the tappet setting for a Honda Ballarde 160i


If your not sure then do a me 12th inlet and 15 exhaust this will cover most cooking engines but not some GT older models .Yes iam aware what the so called bar room mechanics say about my advice but so long as it has a gap then it will run .All old british leyland engines were around this figure but some ford GT engine had wide gaps and clattered but ?? and some renaults had gaps as small as 4th and 8 th but this honda comes underthe catagory of what we call in the trade cooking engines .IE to go to the shops in and the school run

Oct 15, 2012 | Honda Ballade Cars & Trucks

1 Answer

Honda Luxline 1500 16v getting hot.


most common fault,have you bled ALL the air out of the water system?????

Jun 07, 2010 | 1993 Honda Civic 4 Door

1 Answer

I have a 92 chevy 3500 w/ throttle body 2wd. its showing me error code 12. the manual doesnt have a 12 code for this truck.


code 12 is the diagnostic code. its only purpose is to let you know that the system is in diagnostic mode. if this is the only code you are getting, your system is fine.

Jul 16, 2008 | 1988 Chevrolet C/K 3500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...