Question about Cars & Trucks

Open Question

Gwm steed 2.8d

Took of my flywheel to change rear seal i put it back and now it wont start please can you help

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 2187 Answers

SOURCE: i took my Mazda 323 1.6 engine at the Auto repair

Try this if you have rge 323 BG

Valve clearance - inlet: 0.30 c mm (cold)
Valve clearance - exhaust: 0.30 c mm (cold)

Posted on Jun 04, 2009

Ad
  • 35 Answers

SOURCE: change rear whell seal 1997 f-150

replace the axle seal to replace pull the rear cover draining the gear oil then rotate the carrier around till the small bolt holding the carrier pin remove bolt pull pin out don"t turn carrier after pulling the pin push the axle in and remove the clip from the inside of the carrier that pin holds the axle clips in place after pulling out you can remove the axle then just pop the seal out and install new one use a socket or something that is the same size as the seal lube the axle and slide axle back in lift up when almost all the way in the tube putting it in the carrier once in replace clip and pullout on the axle thats it pretty much hope this helps you out

Posted on Mar 24, 2010

  • 1403 Answers

SOURCE: i have a 2002 1500

try one simple thing, reset the computer by disconnecting positive cable from battery for 10 mins.also make sure the crankshaft sensor is plugged back in,will not start without it.he may have missed it when removal of transmission.you may even have to reset the trucks computer,disconnect the positive cable from battery for 10mins.. this will accept any new products,i'm sure they had to unplug the 02 sensors to remove the transmission! this will help, is it getting fuel? if not,try fuel pump fuse,or relay. is it getting fire to plugs? if not, something is not plugged back in right. suggest you check under and on top of motor for a missed plug in. it was running when they replaced rear seal?go from there. hope this helps and thank you for choosing fixya.com chat support is available,phone support also.

Posted on Dec 23, 2010

  • 1 Answer

SOURCE: i have a gwm steed 2.8 tdi. my power dissapears

hi this is a turbo problem, i have the same issue if you remove the air filter pipe from the turbo and check the play on the axle you'll notice that it is way loose

Posted on Feb 04, 2011

  • 12 Answers

SOURCE: I have a GWM Wingle / Steed 2.8TC. After every

I have the same problem few days ago, and still didn't find any solution. Can any one please help?????19

Posted on Jul 28, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Gwm Steed 2.5D Cleaned crank sensor now it does not want to start what could be the problem.


How did you clean it? If submerged in parts washer, replace unit. I have no idea what a Gwm Steed might be, but why did you clean this part?

Jul 25, 2016 | Cars & Trucks

1 Answer

GWM Steed 2.8td not starting


Hi , this may sound funny but i found on other pickups that would not start the battery was ok the alt was ok it ended up the coolant sensor was duff replaced it and the car started ok.

Dec 18, 2015 | Cars & Trucks

1 Answer

Does the GWM Steed 5 2.2 Petrol D/Cab have a timing belt and if so, at how many kilometers should it be changed?


either a belt or a chain there is no set number when it needs changed some fail before 10,000 and many go over 200,000 without any problems

Feb 23, 2015 | Cars & Trucks

1 Answer

Replace crankshaft seal


Front one isn't bad. Remove the belt/s. Remove the harmonic balancer. pry the seal out and replace it using a hammer. be nice to it. The rear seal, pull the transmission. pull the flywheel. remove the seal and be nice to it putting it back in.

Oct 31, 2014 | 1989 Dodge Ram 50

1 Answer

GWM steed 5 2012 model. Does not start all


does it crank over to start , are you getting fuel , is the battery good , answer any one of these and it should start ,fuel ,spark and air is all it takes to start .

Sep 21, 2014 | Cars & Trucks

2 Answers

2003 dodge Intrepid 2.7l oil leak above rear main seal after running 20 minutes


rear main seal usually only leaks when the car is running. though oil will slowy drip off afterwards. now the best way to tell is to remove the heat sheild that covers the flywheel and look at it and at the flywheel . is the oil only on the engine side of the cover or is it inside the cover and on the fly wheel. the rear main seal will leak into the bellhousing and on the fly wheel the oil pan gasket will leak on the front of the heat sheild.

Source:

former chrysler mechanic

May 24, 2014 | 2003 Dodge Intrepid

1 Answer

Gwm steed


little plug u pull out at back then twist the bulb an pull out

May 07, 2014 | Cars & Trucks

2 Answers

Gwm steed repair manual


gap should be 0.8mm

Jan 14, 2014 | Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...