Question about 1994 Chevrolet G20

1 Answer

How do you remove the back seat from a 1994 chevy g20 van?

I need to remove power folding rear seat from my 1994 Chevrolet G20 Conversion Van

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 186 Answers

I believe the seats are bolted to the floor of the van. Make sure you unplug all electrical connections before removing the seats.

Posted on Mar 11, 2014

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Shouldibuyit
  • 44 Answers

SOURCE: replace heater core 1994 chevy g20 conversion van

Here a are the instuctions to remove it. I did not know if you have A/C or not so I included both for you.

REMOVAL & INSTALLATION
Without Air Conditioning
ALL MODELS
See Figure 1

  1. Disconnect the negative battery cable.
  2. Remove the coolant recovery bottle.
  3. Place a pan under the van and disconnect the heater intake and outlet hoses. Quickly remove and plug the hoses and support them in an upright position. Drain the coolant from the heater core into the pan.
CAUTION When draining engine coolant, keep in mind that cats and dogs are attracted to ethylene glycol antifreeze and could drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantity. Always drain coolant into a sealable container. Coolant should be reused unless it is contaminated or is several years old.
  1. Remove the heater distributor duct-to-case attaching screws and the duct-to-engine cover screw. Remove the duct.
  2. Remove the engine cover.
  3. Remove all the instrument panel attaching screws.
  4. Carefully lower the steering column. Raise and support the right side of the instrument panel. Refer to for further details.
  5. Remove the defroster duct-to-case attaching screws and the two screws attaching the distributor to the heater case.
  6. Disconnect the temperature door cable. Carefully fold the cable back and out of the way.
  7. Remove the three nuts from the engine compartment side of the distributor case and the screw from the passenger compartment side.
  8. Remove the heater case and core assembly.
  9. Remove the core retaining straps and remove the core.
To install:
  1. Install the core.
  2. Install the core retaining straps.
  3. Install the heater case and core assembly.
  4. Fasten the three nuts on the engine compartment side of the distributor case and the screw on the passenger compartment side.
  5. Connect the temperature door cable.
  6. Install the defroster duct-to-case attaching screws and the two screws attaching the distributor to the heater case.
  7. Install the steering column.
  8. Fasten all the instrument panel attaching screws.
  9. Install the engine cover.
  10. Install the duct. Install the heater distributor duct-to-case attaching screws and the duct-to-engine cover screw.
  11. Connect the heater intake and outlet hoses.
  12. Fill the cooling system.
  13. Install the coolant recovery bottle.
  14. Connect the negative battery cable.
1990-95 MODELS With A/C

  1. Disconnect the battery ground cable.
  2. Remove the engine cover.
  3. Remove the steering column-to-instrument panel bolts. Lower the column carefully.
  4. Remove the upper and lower instrument panel attaching screws. Remove the radio support bracket screw.
  5. Raise and support the right side of the instrument panel.
  6. Remove the lower right instrument panel bracket.
  7. Remove the vacuum actuator from the kick panel.
  8. Disconnect the temperature cable and vacuum hoses at the case. Remove the heater distributor duct from over the engine hump.
  9. Remove the two defroster duct-to-firewall attaching screws below the windshield.
  10. Under the hood, disconnect and plug the heater hoses at the firewall.
  11. Remove the three nuts and one screw (inside) holding the heater case to the firewall.
  12. Remove the case from the van. Remove the gasket for access to the screws holding the case together. Remove the temperature cable support bracket. Remove the screws and separate the case. Remove the heater core.
To install:
  1. Install the heater core.
  2. Assemble the case and fasten the screws.
  3. Install the temperature cable support bracket.
  4. Position the gasket, then install the case in the van.
  5. Fasten the three nuts and one screw (inside) holding the heater case to the firewall.
  6. Connect and plug the heater hoses at the firewall.
  7. Fasten the two defroster duct-to-firewall attaching screws below the windshield.
  8. Install the heater distributor duct.
  9. Connect the temperature cable and vacuum hoses at the case.
  10. Install the vacuum actuator at the kick panel.
  11. Install the lower right instrument panel bracket.
  12. Fasten the radio support bracket screw.
  13. Fasten the upper and lower instrument panel attaching screws.
  14. Fasten the steering column-to-instrument panel bolts.
  15. Install the engine cover.
  16. Connect the battery ground cable.
  17. Refill the cooling system as necessary.

Posted on Nov 28, 2008

  • 1 Answer

SOURCE: Electronic Control Module Installation 1994 G20 Chevy Van

I just had the same problem. If it is a regular van try under the driver seat in a plastic box. If it is a conversion van try in a pannel just behind driver seat on side of van wall behind a pannel that looks like a vent.

Posted on Apr 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1994 G20 conversion van. 6 cylinder. Engine running in park. When I apply brake. Engine quits then van will not restart.


Check vacuum lines.
There is a large one on the power brake booster that goes to the back on the fuel system. Make sure you have vacuum before you try anything else.
A vacuum leak will cause you to stall out.

Dec 28, 2016 | 1994 Chevrolet G20

1 Answer

1990 Chevy van fusebox location


Donald, You did not state the model, so I posted the link for the models I found for chevy van fuse box. Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
Interior Fuse Box Location 1990 1996 Chevrolet G20 1994 Chevrolet G20...
Blown Fuse Check 1990 1996 Chevrolet G20 1994 Chevrolet G20 Chevy Van 4 3L...
fuse box diagram 1990 chevy astro van pdf 1 Docs Engine com
1990 Chevy van fusebox location Google Search

Jul 27, 2016 | Cars & Trucks

1 Answer

Where can I find a fuse block diagram for a 1994 chevy g20 van?


google fuse block diagram for a 1994 chevy g20 van, should pop right up

Jan 07, 2015 | Chevrolet Cars & Trucks

1 Answer

Manual for 1994 chevy g20 custom conversion van


If you need a shop manual for the chassis you can get a used book from Ebay. If it involves lights or other accessories for the conversion part of the van you could try contacting the company that did the original conversion. I doubt they print books with diagrams for the public.

Jan 08, 2013 | Cars & Trucks

1 Answer

How to remove engine cover for 1994 van


Unscrew console bolts nr floor and screws behind ash tray push seats back as far as possible then flip the tension clamps on both sides to release then lift outward and upward

Jun 24, 2012 | 1994 Chevrolet G20

1 Answer

We have a 199 Chevy conversion van that has a full bench seat in the very back with a rear facing seat and we can't figure out how to lay the seat down now that we need to. The switch will click when...


I have the same problem. found out you like i have a power fold down seat. there should be a small motor mounted underneath the rear seat. attached to it are two cables. those cables are what move the seat up and down. check to see if the cables are broken or snapped apart. then check all the seat levers support bars to find out if any of them are bent or misaligned. that can cause your cables to break.

Aug 06, 2011 | 1995 Chevrolet G20

1 Answer

5 to 8 lug conversion


you may need to use the control arms, springs and knuckles, as the ball joints of the 93 g20 may not fit the 96 g3500.

Mar 07, 2010 | 1993 Chevrolet G20

2 Answers

Need a guide of where the fuses go on a 95 Chevy G20 Van


The fuses are located on a fuse block, they provide increased circuit protection and reliability. The fuse block is located under the left side of the instrument panel and steering column. The fuse block should be visible from underneath the steering column, near the pedal bracket. If the block is not visible, check for a removable compartment door or trim panel which may be used on later models to hide the block. On 1996-97 models, there is also a fuse/relay panel mounted underhood.

e5fef9f.jpg

Fig. 1: If the fuse panel has a concealed cover, unscrew or unclip the retainer and remove the cover:

18e20c4.jpg

Fig. 2: Some fuse panel covers contain a fuse puller, spare fuses and a diagram of the fuse locations:

Good luck (remember rated this help).

Mar 02, 2010 | 1995 Chevrolet G20

1 Answer

1990 G-20 Htr core frt bypassed, what is correct routing of


there should be 3 places where the hoses connect on the Tee, see what ones are looped -one into the other, the heater core goes on these 2 in & out, the other goes to the rear air if equipped, such as in a conversion van.

Oct 03, 2009 | 1994 Chevrolet G20

2 Answers

Electronic Control Module Installation 1994 G20 Chevy Van


I just had the same problem. If it is a regular van try under the driver seat in a plastic box. If it is a conversion van try in a pannel just behind driver seat on side of van wall behind a pannel that looks like a vent.

Dec 28, 2008 | 1987 Chevrolet G20

Not finding what you are looking for?
Cars & Trucks Logo

318 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...