Question about Volkswagen Jetta

Open Question

HOW TO REPLACE A LEFT REAR DOOR WINDOW GLASS - Jetta Volkswagen Cars & Trucks

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 56 Answers

SOURCE: I need to changeout a broken left rear door

remove the panel screws and the handle screws and clips usually behind window handle, if electric ok.
remove panel lift bottom out and panel up after clearing door base, be careful not to pull wires or break plastic. lower window so bolts of lower/mid
trac is visible. loosen but have someone hold the window from falling inside, it will break easily so don't torque or drop it inside. once trac is loose remove
through top but turning if necessary to clear the top of the door. not too easy

Posted on Feb 10, 2010

Testimonial: "great help,could not have done it without the info, Thanks"

vinniepow31
  • 45 Answers

SOURCE: Auto functioning of Left front door Glass failure

ok your electric window motor is broken ,..very easy to replace,if you buy second hand one

Posted on Jun 19, 2010

  • 7353 Answers

SOURCE: replace the left rear electric window cable.

you cant fix cable, you need the Window Regulator

Posted on Jul 24, 2010

  • 5470 Answers

SOURCE: I am replacing a driver’s side rear faulty power

Good question. The motor has a gear drive for the plastic cable which moves the window. When you loosen the bolts for the motor, there will be a separation of the gear from the plastic cable. Then you will be able to move the window without interference from the motor.

There can be several ways to brace the window. You may find metal braces inside the door. I use some "C" clamps about 3"long that I obtained from Big Lots. But you can also use small Vice grip pliers and wood. Just clamp the wood to a brace and rest the window on the wood.

There is not a lot of room to work with, but the motor is easy to change out. One word of advice- if you can unplug the wires from the old motor before you remove it, plug the new motor into the harness before you take even 1 nut off the old motor. Remember to have the Ignition Key in Run position or the vehicle running.

Then try the new motor. Your problem may just be a bad switch. I hope you have been helped by my solution.

Posted on Dec 01, 2010

Bradbury Phi
  • 3 Answers

SOURCE: rear door glass fell down, will not wind back up.

For a X reg (2000) Jaguar S- type: to remove the rear left winder mechanism do the following... Remove the door panel: remove two Philips Screws from under the small rubber mat in the door pull recess. Starting at top outer edge lever the panel away from door using something that does not damage the paint (I used a flat wooden spatula) - you will hear the poppers as they release the panel; work down and around the panel using your fingers. At some point the bezel around the door opening handle will become loosened and you need to carefully remove it - I found this awkward. Lift the panel upwards off the door and remove the cable that goes to the switches. Next remove the large access cover made of soft material stuck on with body putty and the circular sticky plastic disc covering a hole in the lower centre of the door. Remove the loudspeaker - four bolts into door metal and a cable. Remove the trim strip from the bottom edge of the window opening. Assuming the window can be moved slide it so the securing peg can be seen through the small hole uncovered when you removed the sticky plastic disk. It appears as two concentric circles of plastic, outside diameter about 1cm, with a hole through the middle. Knock out the middle peg with a punch of about 4mm dia. This will disappear into the door and will be needed later! Once the inner peg is removed the split outer peg can be pushed through releasing the window from the regulator mechanism. Pull the window all the way up and secure with duct tape to the side of the frame so it doesn't crash down. Remove three nuts securing the mechanism push it in to the door void and remove the electric plug. I did this through the speaker apperture and found it awkward to get out - patience is needed if yours is as difficult. Manoeuver the mechanism out through the access hole and survey the damage.

Posted on Mar 28, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the Power Windows Fuse in a 2005 Ford Taurus?


It is located in the SJB smart junction box , it's a fuse / relay center / microprocessor ! Fuse # F2.10 30 amp . location -behind left side dash panel . Also check the accessory relay . Top relay left side , same location SJB .
Visual Inspection Chart Mechanical Electrical
  • Door window regulator and motor
  • Door glass top run
  • Door window glass
  • Loose, corroded connectors
  • Circuitry
  • Window control switch
  • Battery junction box (BJB) fuse(s):
    • 1 (60A)
    • 3 (60A)
    • 11 (50A)
  • Smart junction box (SJB) fuse(s):
    • 7 (20A)
    • 27 (10A)
    • 30 (10A)
  • SJB circuit breaker 10 (30A)
  • SJB rear window defrost relay 1
  • Relay center box 1 rear window defrost relay 2
  • Delayed accessory relay
  • Battery saver relay
  • Rear window defrost grid

Sep 23, 2015 | 2005 Ford Taurus

1 Answer

Does the window need to be up to replace the window regulator in the left rear door. If it is binding how do you fix it? Is there a track for the window both front and back? The back is in the track


Hi Lennie you need to detach and remove the glass altogether to replace the regulator. When you remove the door cover you can see the bolts holding the reg in place. At the bottom of the glass are two clamps with clips or bolts holding the glass to the reg. when you have the glass out then remove the reg bolts and the wiring harness. Refit all in reverse order. Regards Jim...

May 08, 2015 | Dodge Durango Cars & Trucks

1 Answer

The left rear door window fell off the track. How do I remove the door panel to access it.


This is the complete procedure you stop when you see the problem.



1. REMOVE REAR DOOR INSIDE HANDLE BEZEL


(a) Remove the screw.


(b) Using a screwdriver with its tip taped, disengage the 2 claws A.


(c) Pull out the the rear door inside handle bezel in the direction indicated by the arrow, disengage the claw B, and remove the rear door inside handle bezel.


2. REMOVE DOOR PULL HANDLE


(a) Using a screwdriver wrapped with the protective tape, disengage the 2 clips and remove the door pull handle.


3. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY


(a) Remove the screw.


(b) Disengage the 7 clips.


(c) Disconnect the connector and pull up on the rear door trim board sub-assembly to remove it.


4. REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY


(a) Remove the bolt.


(b) Disengage the 2 claws and separate the rear door inside handle sub-assembly.


(c) Disconnect the 2 cables and remove the rear door inside handle sub-assembly.


5. REMOVE REAR SPEAKER


6. REMOVE REAR DOOR SERVICE HOLE COVER


(a) Disconnect each connector and remove the rear door service hole cover.


HINT:


Remove the remaining tape on the door side.


7. REMOVE REAR DOOR GLASS RUN


(a) Connect the window regulator switch assembly.


(b) Fully lower the door glass.


(c) Remove the rear door glass run.


8. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY


(a) Remove the 2 bolts, the screw and rear door window division bar sub-assembly.


9. REMOVE REAR DOOR QUARTER WINDOW GLASS


(a) Pull out the direction indicated by the arrow, remove the rear door quarter window glass and rear door quarter window weatherstrip as a unit.


10. REMOVE REAR DOOR QUARTER WINDOW WEATHERSTRIP


11. REMOVE REAR DOOR GLASS SUB-ASSEMBLY


(a) Remove the rear door glass sub-assembly as shown in the illustration.


(b) Disconnect the window regulator switch assembly.


12. REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY


(a) Disconnect the connector.


(b) Loosen the temporary bolt.


NOTICE:


If the temporary bolt is removed, the rear door window regulator may fall and become deformed.


(c) Remove the 3 bolts and the rear door window regulator sub-assembly and the power window regulator motor assembly rear as a unit.


(d) Remove the temporary bolt from the regulator.


13. REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY REAR


(a) Using a "torx" driver (T25), remove the 3 screws and power window regulator motor assembly rear.


14. REMOVE REAR DOOR LOCK ASSEMBLY


(a) Disconnect the connector.


(b) Remove the bolt.


(c) Using a "torx" socket wrench (T30), remove the 3 screws.


(d) Slide the rear door lock assembly downward, pull out the link from the outside handle frame, and remove the rear door lock assembly and cables as a unit.


(e) Remove the door wire harness packing.


(a) Using a "torx" socket wrench (T30), loosen the screw.


(b) Disengage the 2 claws and remove the rear door outside handle cover.


(a) Disengage the 2 claws and remove the rear door outside handle pad rear.

Jan 03, 2011 | 2006 Toyota Highlander

1 Answer

My rear power window will not rise


One thing that makes the repair easier is to move the glass back up into door. Then use a small block of wood and a small C clamp to press the wood against the vertical structure inside the door frame. This will provide a soft brace for the glass.
You may be able to get the plastic window regulator to disengage the gear and allow you to move the glass up and out of the way.

There is a difference between the 2 rear sides of the doors and you need a left to go on the left and so on. In earlier models the motors would criss-cross and the right front matched the left rear.

Feb 22, 2010 | 2003 Ford Crown Victoria

1 Answer

How do i replace left door mirior


remove trim panel, remove mirror fasteners.

Glass, Outside Mirror—Town Car

Removal and Installation
  1. Push upper edge of outside rear view mirror glass (17K707) into the outside rear view mirror to expose latch release.
  1. Using a small flat-bladed screw driver or equivalent, move latch release to released position.
  1. Remove outside rear view mirror glass mounting back and outside rear view mirror glass from outside rear view mirror.
  1. Disconnect heater wire connectors and auto dimmer connector, if equipped.
  1. To install reverse Removal procedure.
------------------------------------------------------------
Mirror, Power—Outside Rear View
Town Car

Removal and Installation
  1. Disconnect battery ground cable (14301). Refer to Section 14-01 .
  1. Remove front door trim panel (23942). Refer to Section 01-05 .
Trim Panels, Door Front—Town Car
Removal
  1. Snap out two door pull strap retaining screw covers. Remove screws.
  1. Remove three screws on front and rear side and center of front door trim panel (23942).
  1. NOTE: The following procedure must be used during removal and installation of the door armrest and trim panel. Refer to the appropriate illustrations for component and vehicle model identification.

    Using the Trim Pad Removing Tool from Rotunda Windshield and Moulding/Trim Removal Kit 107-R0401 or equivalent, pry the trim panel retaining clips from the door inner panel.
  1. NOTE: Do not use front door trim panel to remove trim clips from door inner panel. Replace any bent, damaged or missing push pins.

    Remove window regulator control switch housing from front door trim panel. Lift up housing in front and disconnect all connectors.
  1. Disconnect wiring harness and heated seat switch electrical connectors if equipped.
  1. Remove the door trim panel.
  1. Disconnect two electrical connectors.
  1. Remove nut from outside rear view mirror mounting base.
  1. Swing outside rear view mirror (17682) toward driver door window glass to expose screw in mount base.
  1. Remove screw from outside rear view mirror base.
  1. Remove outside rear view mirror from front door (20124). Guide wiring and connectors through hole in front door.
  1. To install, reverse Removal procedure. Tighten nuts to 8-10 Nm (71-88 lb-

Nov 05, 2009 | 1996 Lincoln Town Car

2 Answers

Need to replace a broken window on rear passenger 1999 jeep chero


This information can help you to fix it:
- Section-08s-Power-Window-Systems-Ewj8s
- Section-23-Body-ewj23S (Rear Door, page 41 and next).

Good luck (remember rated this help).

Sep 09, 2009 | 1999 Jeep Grand Cherokee

1 Answer

How to remove rear window in 1992 Jetta


there is difference but you did'nt mentioned the rear window but which one sir the rear main windshield glass or the rear door left or right door glass . 1. the rear windshield glass comes with a fixing silicon compond or silicate material which hold the glass firmly fixed attached to the body untill it break up then in this you need to consult to your nearest authorised dealer or authorised service centre for changing or removal of this sort's of glass  2. the rear door glass weather it is left side or right side the auto mechanic can do the job for you it's simple you your self can do for youself but some precaution measure has to be taken or either the glass will get break up so better consult the authorised service station 1st so for more soultion do write to us & till then drive safe drive carefully...!

May 24, 2009 | 1992 Volkswagen Jetta

1 Answer

Rear Window- Drivers side- won't work


Removal and Installation
  1. Remove the rear door trim panel. For additional information, refer to Section 501-05 .
  1. Remove the watershield.
  1. Remove the interior weatherstrip.
  1. Remove the exterior-weatherstrip.
  1. Remove the nut and the rear window stabilizer.
  1. syh~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Prior to removing the rivet center pins, place suitable support between the door outer panel and the glass to stabilize the glass.
    NOTE: Lower the window to access the rivets.
    Remove the two rivets retaining the rear door window glass to the rear door window glass run and bracket.
9eaea6b.gif
  1. Remove the rear door window glass.
  1. To install, reverse the removal procedure.

Apr 09, 2009 | 2000 Ford Taurus

3 Answers

Hey when i push the power botton for the rear window it doesn't go down,I checked the power button,and its good ! Can i replace the power motor in the rear window,and where is it located,i would like to...


  1. Raise and support the rear door window glass to the full up position.
  2. Remove the interior door handle.
  3. Remove the rear door speaker.
  4. Remove the water shield.
  5. Disconnect the rear door window regulator motor electrical connector.
  6. Remove the rear door window regulator rivets.
  7. Remove the rear door window regulator by sliding the regulator arms off of the window glass track.
  8. Installation is the reverse of the removal procedure, noting the following:
    • Cycle the door glass to make sure of engagement of the drive mechanism.
    • Remove the rear door window glass-to-regulator bolt or rivet.
    • Position the rear door window glass as necessary to access the rear door window glass-to-regulator rivet.
    • Secure the rear door window glass in the full UP position with tape.
    • Disconnect the window regulator motor electrical connector.
    • Remove the 2 window regulator nuts.
    • Remove the 3 window regulator motor bracket nuts.
    • Install the window regulator assembly. Tighten the 3 motor bracket nuts to 89 inch lbs. (10 Nm).
    • Install the 2 window regulator nuts. Tighten the nuts to 89 inch lbs. (10 Nm).
    • Connect the window regulator motor electrical connector.
    • Remove the tape securing the rear door window glass in the full UP position.
    • Position the rear door window glass as necessary to access the rear door window glass-to-regulator rivet. Tighten the bolt to 62 inch lbs. (7 Nm), or install a new rivet.
    • Install the window regulator motor
    • Remove the window regulator assembly.
Remove the window regulator motor

Feb 23, 2009 | 2001 Ford Explorer

1 Answer

'88 toyota camry rear window stuck in down position


To get to the Window:

Remove Door Inside Handle:
remove screw, slide the handle forward.
Disconnect the control link and remove the handle.

Remove Door Trim with Inner WeatherStrip:
Remove the two screws from the armrest.
Insert a screwdriver between the trim retainers and the door panel to pry it loose.  Eight hidden fasteners. 1 top left side of door.
1 right side about same height as top of armrest. 1 (each side) about same height as bottom of armrest. 1 on each corner bottom. 1 bottom in middle.  1 on left side between bottom corner and the previous at about lower armrest height...

Remove Service Hole cover.
Remove Door Glass Run.

Remove Division Bar (upper window section divider):
Remove the two screws under the weatherstrip
Remove the bolt.
Pull out the division bar.

Remove the Window Glass:
Place the glass in the door cavity.
Remove the two glass channel mounting bolts.
Remove the window glass by pulling it upwards.

You now have access to the Power Window Regulator; possible replacement of motor etc.

What type of 'things' have you tried for fixing the window and restoring operation?

Jan 22, 2009 | 1988 Toyota Camry

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75066 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...