Question about 2001 Chevrolet Silverado 2500

1 Answer

SPRINGSBROKE NEED A USED OR NEW DRIVER SEAT

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 3,961 Answers

You won't want to get a new one, it isn't economic. Try a motor wreckers which specializes in this model, and swap springs if needed. You could also try a motor trimmer, but I think he will send you to the motor wreckers again.

Now a trick. If you have all the pieces, it is possible to tack weld them together again. Any competent stick welder can do this. The springs may again break in a while, but it is worth a try.

Posted on Feb 11, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Removing front driver seat


Hi Edward, if you are only changing the drivers seat with a new one, here's how its done. You'll need to move the seat reward all the way, then remove the 2 bolts holding the seat to the floor, then move the seat all the way forward and remove the 2 bolts holding the seat to the floor. NEXT, tilt the seat up and unplug all connectors that run from the floor to the seat. Thats it, reinstall your new seat in reverse procedure. Hope this helps, have an awesome day Edward.

Apr 21, 2014 | 2005 Dodge Neon SXT

1 Answer

I have a 2002 gmc envoy xl. the heat and seat and mirrors work fine, however every time i turn the car on or off the seat shifts all the way forward and the mirrors tilt in. to solve some of the...


Memory Seat System Components
The memory seat system consists of the following components:
• Power Seat Switch
• Seat Horizontal Motor
• Seat Front Vertical Motor
• Seat Rear Vertical Motor
• Seat Recliner Motor
• Driver Seat Module
• Memory Seat Switch

It's not the module , probably sensor supplying bad info to the module.

Memory Set/Recall Operation
The driver seat adjuster motors are equipped with potentiometer type position sensors used by the driver seat module to determine the seat position. The position sensors are supplied with 5-volt reference and ground circuits from the driver seat module. The position sensor signal circuits are referenced from ground within the driver seat module. The signal circuit voltage levels monitored by the driver seat module range from 0.39 - 4.58 volts and are determined by the wiper locations on the resistors within the motor position sensors. The position sensor circuit voltage levels are used by the driver seat module to determine the seat position when storing or recalling memory position settings.
The memory recall switch assembly on the driver's door provides inputs to the driver door module. Battery voltage is supplied to the memory recall switch assembly from the driver door module. When a memory recall 1, 2, or EXIT switch is pressed, the switch contacts close the appropriate switch signal circuit to the battery voltage supply circuit within the memory recall switch assembly. When the driver door module receives active switch signals from the memory recall switch assembly, the appropriate commands are sent to the driver seat module using the Class 2 Serial Data circuit.
Memory seat recall operation is allowed only with the transmission selector lever in the PARK position while the ignition is on. The transmission selector lever position data is provided to the driver seat module by a message through the Class 2 Serial Data circuit.

Your best bet , take it to a qualified repair shop and have it checked for DTC'S - diagnostic trouble codes .
Install a scan tool.
Observe the switch parameter for which the DTC has set in the seat module Inputs/Outputs data list.
Does the scan tool display Inactive?
DTC B1735, B1740, B1745, B1750, B1755, B1760, B1815, or B1820
DTC B1825, B1850, B1860, B2355, B2365, or B2375
The driver seat adjuster motors are equipped with potentiometer type position sensors used by the driver seat module to determine the seat position. The position sensors are supplied with 5-volt reference and ground circuits from the driver seat module. The position sensor signal circuits are referenced from ground within the driver seat module. The signal circuit voltage levels monitored by the driver seat module range from 0.39-4.58 volts and are determined by the wiper locations on the resistors within the motor position sensors. The position sensor circuit voltage levels are used by the driver seat module to determine the seat position when storing or recalling memory position settings.

$316.00 from doorman

Aug 15, 2017 | GMC Cars & Trucks

1 Answer

What bolt do I need to fix the reclining driver seat for a 98 Toyota Camry?


Remove the same bolt off the other seat and take it to Autozone and get a new one.

Feb 16, 2013 | 1998 Toyota Corolla

1 Answer

2002 ford escape airbags replaced , light still on


You need to replace the airbag control module, it is a one time use device.

Jun 21, 2017 | Cars & Trucks

1 Answer

1998 Blazer: power seat quit working on driver side....


Power seat quit working on driver side.

ITs the power seat motor itself. unplug the harness conected below the seat switch and check if it reciving and current when the switch in on if it does then reconnect it and chech the current on the other wires when u move the switch if it doed then bro u need a new motor .There are four bolts located below the seat.open them and check for a new motor...

May 17, 2010 | 1998 Chevrolet Blazer

1 Answer

Power mirrors, driver power seat, adjustable pedals all don't work... checked fuses and all ok... Any suggestions?


it sounds like the driver seat module. It controls all of these items.
buy used at car-part.com. look on page with * for lowest price.
buy new at discount at tascafordparts.com

  • The memory mirror is inoperative
  • Driver seat module (DSM).
  • Circuitry.
  • CJB fuse 3 (7.5A).
  • Exterior mirror motor.
  • Mirror control switch.


  • The memory seat is inoperative
  • Circuitry.
  • Seat control switch.
  • Seat track.
  • DSM.
  • PDJB Fuse 109 (30A).
  • Power seat motor.


  • Adjustable brake pedal does not operate correctly — does not operate using the adjustable pedal switch
  • Battery junction box (BJB) fuses:
    • 109 (30A).
  • Circuitry.
  • Switch.
  • Adjustable pedal motor.
  • Driver Seat Module (DSM

Oct 02, 2009 | 2003 Ford Expedition

2 Answers

I am having a problem with my srs, dealer told me its the drivers seat sensor and they have to replace the seat for 3K+ I was wondering if I could just go to a pick and pull and find a seat thats...


It will not recognize the new seat and it is against the law for a used airbag sensor to be used so a dealer will not reset it for you. It is a tough place to be in. I would call a few body shops. They might night charge as much, but are set up to reprogram airbag systems.

Hope this helps.

Aug 28, 2009 | 2004 Toyota Camry

1 Answer

The rear wind shield wipers wont work and the driver seat


for the rear wiper check fuses # 7 and #12 in the fuse box inside the vehicle.....as far as the seat one of the seat motors are bad and the only way to repair it is get a used seat or order a new seat tack from the dealer...the motors are not offered separate

Nov 15, 2008 | 1999 Dodge Durango

1 Answer

Explorer seat


You need a new or used passenger seat tilt lever. Mine broke also. There are a couple on sale on EBay for $30.00. See link, otherwise you can buy new from Ford for about $75.00.
http://cgi.ebay.com/ebaymotors/FORD-EXPLORER-DRIVER-SEAT-TILT-LEVER-ASSEMBLY-91-94-OEM_W0QQcmdZViewItemQQcategoryZ33701QQihZ023QQitemZ360071362943QQrdZ1QQsspagenameZWDVW

Jun 28, 2008 | 1997 Ford Explorer AWD

1 Answer

1998 MITSUBISHI MONTERO POWER SEAT MOTOR


I FOUND AFTER SEVERAL TEST THAT THE PROBLEM WAS THE SWITCH CONTROL ATTACHED TO THE SIDE OF THE DRIVER SEAT NOT THE COMPUTER UNDER THE DRIVER (THAT COST A LOT OF MONEY) SEAT. MY BEST RECOMMENDATION CALL PITSTOP AUTO WRECKING AT (818)899-0226 THEY ARE SPECIALIST IN USED MITSUBISHI PARTS IN SUN VALLEY CALIFORNIA. IT MAYBE COST NO MORE THAN $150 AND IT IS EASY TO INSTALL

Jun 05, 2008 | 1998 Mitsubishi Montero

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...