Question about Pontiac Sunfire

Open Question

Location of oil sending unit 2.5 engine - Sunfire Pontiac Cars & Trucks

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 508 Answers

SOURCE: locate the oil sending unit on a 2003 6.0 2500HD silverado

You will find it down by the oil filter.

Posted on Feb 07, 2009

farroutideas
  • 78 Answers

SOURCE: oil pressure sending unit

Hi there;

Your looking foer the oil pressure sensor on the 2004 8.1L.
You will find it located directly behind the EGR valve threaded into the block just to the drivers side of the center bolt for the transmission to block connection.

Thanks
Farrout!

Posted on Mar 17, 2009

  • 1 Answer

SOURCE: where is the oil sending unit on a 93 chevy silverado 350 engine

the oil sending unit is located at the back of the motor right below the rotor cap it is about 3 inches long and has a 3 wire plug hooked t it

Posted on Apr 28, 2009

  • 126 Answers

SOURCE: Where is the oil sending unit located on a 2003 Chevy Tahoe 5.3 engine

its in the block behind intake manifold .

Posted on May 05, 2009

  • 400 Answers

SOURCE: where is the oil pressure sending unit located on

Take the passenger front wheel off. Look up under the car by the power steering pump, you'll see the sending unit, it's up and back from where the oil filter is. There is a special GM oil sending unit socket, I'm sure you will be able to buy or barrow one from your local parts store! Make sure to have a catch pan under it when you take it out, they can leak a good amount of oil out when you remove it.

Posted on Oct 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is oil sending unit located on a 2002 honda odyssee 3.5 vtech located


I have done this on a 2003 Odyssey EX. The oil pressure switch is located on the oil pump assembly, which is behind the passenger side front wheel. There are 2 sensors - the oil pressure switch is the furthest one and least accessable. You need to pull off the connector, which is very tight. I used a pair of pliars with a cloth to twist it off. Be carefull not to damage the connector. There are 2 different switches available for the 2003, each with different tread sizes. I used a regular wrench to remove/install the switch, and it stopped the leak that prompted the repair. Another TIP: watch how long your wrench is, because you can catch the power steering pressure switch wiring harness and break the thin wires, leading to a much more expensive repair.... Next time I will disconnect the power steering pressure switch first and pay more attention. Or buy a shorter wrench.... Good luck!After you remove take to Auto part store and match up with a new one.Adeep well socket may also work.here's another site I found on removing.
  1. Locate the oil pressure sending unit on the engine.
  2. Note the anti-theft code and radio presets for the radio.
  3. Disconnect the negative battery cable.
  4. Disconnect the sending unit electrical harness.
  5. Using a pressure switch socket, deep-well socket or wrench, loosen and remove the sending unit from the engine.
To install:
  1. Apply a liquid thread sealant to the sending unit and install the sending unit in the engine and tighten securely.
  2. Attach the electrical connector to the sending unit.
  3. Check the engine oil level and top off as necessary.
  4. Connect the negative battery cable.
  5. Enter the anti-theft code and radio presets for the radio.
  6. Start the engine, allow it to reach operating temperature and check for leaks.
  7. Check for proper sending unit operation.

Aug 12, 2015 | Honda Cars & Trucks

2 Answers

Change oil sending unit 04 tahoe


It is located on rear of engine back by the distributor use to be. see attached pic
25576498-orvua4poo00lqzajd5seke1u-5-0.gif

Mar 15, 2015 | 2004 Chevrolet Tahoe

1 Answer

Where is the oil pressure sending unit located in a '01 dodge dakota, 4.7 eng.?


go to CTC and buy a service manual for 2001 dodge Dakota 4.7 litre engine there will be 2 oil pressure sending units one that is for the gauges in the dash and the other for the oil pressure sending unit mounted on engine

Feb 12, 2015 | Dodge Cars & Trucks

1 Answer

Where is the oil pressure sending unit located on a 1999 oldsmobile alero


2.2L ENGINE OIL SENDING UNIT LOCATED FRONT CAMSHAFT HOUSING ON LEFT DRIVER SIDE OF ENGINE.FOR 3.1L ENGINE OIL PRESSURE SENDING UNIT LOCATED NEXT TO OIL FILTER.

Sep 16, 2011 | 1999 Oldsmobile Alero

1 Answer

Where is the oil sending unit located on a 2002 chevrolet malibu


V6 ENGINE OIL PRESSURE SENDING UNIT LOCATION NEXT TO OIL FILTER. THE 4 CYLINDER ENGINE OIL PRESSURE SENDING UNIT LOCATION IS FRONT CAMSHAFT HOUSING ON THE LEFT DRIVER SIDE OF THE ENGINE COMPARTMENT.

Mar 20, 2011 | 2002 Chevrolet Malibu

1 Answer

My 2003 4x4 1/2 ton oil gauge will go to 80 then to 0 when you are driving is it the sending unit? where is the sending unite ta ? bzibert@hotmail.com


you are on the right track, the first thing would be the sending unit, thats the most common reason for this type of problem,the oil sending unit is located on the top rear of the engine , heres a diagram picture to help you this is of a 6.6 engine as there are 5 engines that come in the truck but all have the oil sensor in the same location, have a good day and hope this helps.johnjohn2_77.gif

Mar 05, 2011 | 2003 Chevrolet Silverado 1500

1 Answer

I need to know where the oli sending unit is and how to replace it?


zjlimited_305.jpg

Fig. 1: Location of the oil pressure switch-3.3L and 3.8L engines


zjlimited_306.jpg

Fig. 2: Location of the oil pressure switch-3.0L engine


zjlimited_307.jpg

Fig.: Oil pressure switch (sending unit) schematic


The low oil pressure warning lamp will illuminate when the ignition switch is turned to the ON position without the engine running. The lamp also illuminates if the engine oil pressure drops below a safe oil pressure level. To test the system, perform the following:

  1. Turn the ignition switch to the ON position.
  2. If the lamp does not light, check for a broken or disconnected wire around the engine and oil pressure sending unit switch.
  3. If the wire at the connector checks out OK, pull the connector loose from the switch and, with a jumper wire, ground the connector to the engine.
  4. With the ignition switch turned to the ON position, check the warning lamp. If the lamp still fails to light, check for a burned out lamp or disconnected socket in the instrument cluster.

REMOVAL & INSTALLATION
On the 2.4L engine, the oil pressure switch is located on the side of the engine block facing the firewall. On the 3.0L engine, the oil pressure switch is located on the oil filter adapter housing, next to the starter motor. On the 3.3L and 3.8L engines, the oil pressure switch is located next to the oil filter.
  1. Locate the oil pressure sending unit on the engine.
  2. Disconnect the negative battery cable.
  3. Disconnect the pressure switch electrical harness.
  4. Using a pressure switch socket, deep-well socket or wrench, loosen and remove the pressure switch from the engine.
To install:
  1. Install the pressure switch into the engine and tighten securely.
  2. Attach the electrical connector to the switch.
  3. Connect the negative battery cable.
  4. Start the engine, allow it to reach operating temperature and check for leaks.
  5. Check for proper oil pressure switch operation.

Hope this helps (remember to rate this answerr).



Dec 22, 2010 | 1999 Plymouth Voyager

1 Answer

Oil pressure gauge is reading 80 psi. I had the


The oil sending unit is located on the engine block behind the drivers cylinder head area.You have to climb up on the motor to see it cause it is hard to see behind the wiring harness.You may also want to purchase a new sending unit because it is very long and you might need to buy the sending unit socket to replace it.Hope this helps.Good luck.

Jul 20, 2010 | 2003 Chevrolet Silverado 1500

2 Answers

Oil pressure sending unit


On all 2.0L and 2.4L engines, the oil pressure sending unit switch is located on the engine block, below the exhaust manifold, on the firewall side. On all 2.5L engines, the oil pressure sending unit switch is located on the engine block, below the front exhaust manifold on the radiator side.

May 24, 2009 | 1996 Plymouth Breeze

5 Answers

Where is the oil pressure sending unit on 2004 dodge stratus?


per the Haynes manual for the 95-05 Dodge Stratus on the 2.0L & 2.4L DOHC 4 cyl engines, the oil pressure sending unit is located at the left end of the rear side of the block. On 2.4L SOHC 4 cyl engines, the sending unit is located at the left end of the rear side of the block. On 2.5L & 3.0L V6 engines, the sending unit is located on the oil filter housing, on the front side of the block. On 2.7L V6 engines, the sending unit is located at the left end of the rear side of the block. To access it, remove the heat shield.

Jan 23, 2009 | 2004 Dodge Stratus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

11 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...