Question about 2000 Ford Windstar

Open Question

Ford Windstar mirror turn signal will not stop blinking

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 7 Answers

SOURCE: Turn signals 2003 Ford F-150

Sounds like the turn blinker is shorted internally. Suggest you change it out, to test this.

My next check is that no wiring is melted and burned, such as can happen with any connection to tow a trailer. U-Haul has fine print that indemnify them of any problems they cause! have you towed anything recently?


Posted on Dec 25, 2008

  • 1596 Answers

SOURCE: help replacing mirror

You Must Remove the Door Trim Opposite the Mirror And There are 3 10mm Bolts there remove them and Disconnect the Plug (FOR Electric) Reverse Procedure For Install.
MOUNTING BOLTS MAY HAVE RUBBER PLUGS HIDING THEM

Posted on Feb 09, 2009

sscullys
  • 984 Answers

SOURCE: change mirror turn signal light in ford 2001

You will need to remove the glass to get to it.

Muth Co signal mirrors have some good directions for getting the door panel off, and removing the glass, available for download on their site.

I prefer to do this with the mirror head off the truck, but you might feel other wise on this part.

Once you have the glass from the mirror removed you will see where the bulb is inserted from the back ( inside ) of the mirror head.

Posted on Nov 13, 2009

  • 85 Answers

SOURCE: looking for fuse box on 1998 ford windstar

Fuse 25 and fuse 27 in the fuse box, under the dash on the driver side, powers the electronic flasher relay that powers the turn sinal switch and turns on the turn signals

Posted on Apr 11, 2010

gandergmm
  • 145 Answers

SOURCE: 1998 Windstar: 1998 ford windstar van overdrive indicator blinkin...

replace TRS (transmission range sensor) and or VSS (in the back of the engine behind the catalytic converter) its a pain to replace. hard to get at and theres an annoying steel cover to deal with
use DTC reader to confirm

Posted on May 26, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Our brake lights tail lights and the turn signals on the mirrors and the gas guage work sometimes and sometimes they don't . Headlights and turn signals in front work all the time .


All of these devices run through a computer control module generally referred to as the GEM (Generic Electronic Module) module, you need the dealer to test this control module with a special scan tool.

Apr 01, 2016 | 2001 Ford Windstar

1 Answer

I have a 2002 ford windstar Es: wen the van is turn of, some times the lights inside stays on and the turning signal on the mirror, I go to drive the van and the doors signal stays on at all times and the...


the ecu runs every thing on the motor and transmission. you have a common problem with the multifunction control module . depends which model windstar . most of them are on the right hand kick panel1_27_2013_8_52_09_pm.png

Jan 27, 2013 | Cars & Trucks

1 Answer

I Need wiring diagram for turn signal on a 1996 ford windstar


The turn signals on your Windstar are controlled by the front electronic module and the rear electronic module. If you are having problems with the turn signals, you should BEGIN diagnosis by scanning these modules for fault codes.

Wjth all that said, If you are having problems with the rear lights, failure of the rear electronic module is pretty common for Windstars.

Jan 31, 2012 | Ford Windstar Cars & Trucks

1 Answer

Turn signals won't work. I changed the fuse under the steering wheel. Still no luck.


Welcome to FixYa.com Does the turn signal light on but no blink?
Thank you for Using FixYa.com Kind Regards, Lee Your FixYa Expert and Master Technician

Feb 11, 2011 | 1998 Ford Windstar

3 Answers

Looking for fuse box on 1998 ford windstar


Fuse panel is located behind the instrument panel to the left of the steering column. There is also a fuse panel located on the left side of the engine compartment. Fuses #25 and #27 on the interior fuse panel are both associated with the turn signals.
I hope this helps you!

Apr 10, 2010 | 1998 Ford Windstar

1 Answer

Flashing ligth not working at all


Hi!!!

If your hazard lights turn on but do not blink, replace flasher.

If your hazard lights don't turn on, check hazard/stop/turn fuse(s).

Let me know how it worked out, good luck.

Mar 26, 2010 | 1998 Ford Windstar

1 Answer

Brake light, reverse light and turn signal issues


Hello. The symptoms you are describing are likely due to a poor ground. Temporarily install a new ground wire by securing a piece of copper wire to the frame with a self tapping screw. Use this ground wire along with the hot wire to see if each of these lights works. If it does, trace the ground wire back to the frame, unscrew it and clean up the metal with emery cloth so you reestablish a good ground.

Jan 28, 2010 | 2003 Ford Windstar

1 Answer

Why do the turn signal lights come on the mirrors when doors open


dont worry is factory sefty so anibady in trafick will see yu,nuver vans hawe same.sefty laike dodge caravan emergenci flasher com on wen doors is open

Mar 13, 2009 | 2001 Ford Windstar

1 Answer

2000 ford windstar, directionals both not working, hazards work f


turn signal flasher module or turn signal switch. I usuall try to wiggle teh column switch or move it slowly up and down, back and forth to help determine if it has a bad contact. if i cant get a failure (or turn signal) that way I begin the testing at the base of the column. the flasher module is a common failure on those and isnt unreasonably priced. if i had no diagnostic procedure i would try that first. oh yea, try turning the hazards on and off rapidly several times. the signal goes through the four way switch.

Dec 31, 2008 | 2000 Ford Windstar

Not finding what you are looking for?
2000 Ford Windstar Logo

Related Topics:

137 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5471 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...